National Instruments 5783 Bedienungsanleitung

GETTING STARTED GUIDE

NI 5783

Four Channel Transceiver Adapter Module

Note Before you begin, complete the software and hardware installation

instructions in the getting started guide for your FlexRIO FPGA module or

Controller for FlexRIO.

The NI 5783 is a FlexRIO adapter module designed to work in conjunction with FlexRIO

FPGA modules and Controllers for FlexRIO.

The NI 5783 is available in two variants. The NI 5783-01 variant is a 40 MHz Elliptic Filter

(Frequency Domain). The NI 5783-02 variant is a 40 MHz Butterworth Filter (Time Domain).

Unless otherwise specified, all descriptions in this document refer to both variants.

The NI 5783 features 4 analog input channels with 16-bit resolution and sample rates up to

100 MS/s, and 4 analog output channels with 16-bit resolution and sample rates up to

100 MS/s or 200 MS/s.

Note The NI 5783 is compatible only with NI PXIe-797xR and NI-793xR devices.

This document explains how to install and configure the NI 5783.

Contents

Electromagnetic Compatibility Guidelines...............................................................................2

FlexRIO Documentation........................................................................................................... 2

Verifying the System Requirements..........................................................................................4

Unpacking................................................................................................................................. 4

Preparing the Environment....................................................................................................... 4

Installing the NI 5783............................................................................................................... 5

Confirming that Measurement & Automation Explorer (MAX) Recognizes the Device........ 5

Recommended Cables...............................................................................................................6

Accessories................................................................................................................................6

Front Panel and Connector Pinouts...........................................................................................6

AUX I/O Connector.......................................................................................................... 8

Block Diagram.......................................................................................................................... 9

Logic Diagram.......................................................................................................................... 9

Component-Level Intellectual Property (CLIP)..................................................................... 10

NI 5783 CLIP..................................................................................................................10

NI 5783 400 MSPS AO CLIP.........................................................................................11

Clocking.................................................................................................................................. 11

Worldwide Support and Services............................................................................................ 12

Where to Go Next................................................................................................................... 12

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory requirements and limits for

electromagnetic compatibility (EMC) stated in the product specifications. These requirements

and limits are designed to provide reasonable protection against harmful interference when the

product is operated in the intended operational electromagnetic environment.

This product is intended for use in industrial locations. However, harmful interference may

occur in some installations, when the product is connected to a peripheral device or test object,

or if the product is used in residential or commercial areas. To minimize interference with

radio and television reception and prevent unacceptable performance degradation, install and

use this product in strict accordance with the instructions in the product documentation.

Furthermore, any modifications to the product not expressly approved by National Instruments

could void your authority to operate it under your local regulatory rules.

Caution To ensure the specified EMC performance, operate this product only with

shielded cables and accessories.

Caution To ensure the specified EMC performance, the length of all I/O cables

must be no longer than 3 m (10 ft).

FlexRIO Documentation

Table 1. FlexRIO Documentation Locations and Descriptions

Document Location Description

Getting started guide

for your FlexRIO

FPGA module or

Controller for

FlexRIO

Available from the Start menu

and at ni.com/manuals.

Contains installation instructions

for your FlexRIO system.

Specifications

document for your

FlexRIO FPGA

module or Controller

for FlexRIO

Available from the Start menu

and at ni.com/manuals.

Contains specifications for your

FlexRIO FPGA module or

Controller for FlexRIO.

Getting started guide

for your adapter

module

Available from the Start menu

and at ni.com/manuals.

Contains signal information,

examples, and CLIP details for

your adapter module.

2| ni.com | NI 5783 Getting Started Guide

Table 1. FlexRIO Documentation Locations and Descriptions (Continued)

Document Location Description

Specifications

document for your

adapter module

Available from the Start menu

and at ni.com/manuals.

Contains specifications for your

adapter module.

LabVIEW FPGA

Module Help

Embedded in LabVIEW Help

and at ni.com/manuals.

Contains information about the

basic functionality of the

LabVIEW FPGA Module.

Real-Time Module

Help

Embedded in LabVIEW Help

and at ni.com/manuals.

Contains information about real-

time programming concepts, step-

by-step instructions for using

LabVIEW with the Real-Time

Module, reference information

about Real-Time Module VIs and

functions, and information about

LabVIEW features on real-time

operating systems.

FlexRIO Help Available from the Start menu

and at ni.com/manuals.

Contains information about the

FPGA module front panel

connectors and I/O, controller for

FlexRIO front panel connectors

and I/O, programming

instructions, and adapter module

component-level IP (CLIP).

FlexRIO Adapter

Module Development

Kit User Manual

Available from the Start menu

at Start»All Programs»

National Instruments»NI

FlexRIO»NI FlexRIO

Adapter Module Development

Kit»Documentation.

Contains information about how

to create custom adapter modules

for use with FlexRIO FPGA

modules.

LabVIEW Examples Available in NI Example

Finder. In LabVIEW, click

Help»Find Examples»

Hardware Input and Output»

FlexRIO.

Contains examples of how to run

FPGA VIs and Host VIs on your

device.

NI 5783 Getting Started Guide | © National Instruments | 3

Table 1. FlexRIO Documentation Locations and Descriptions (Continued)

Document Location Description

IPNet Located at ni.com/ipnet. Contains LabVIEW FPGA

functions and intellectual property

to share.

FlexRIO product page Located at ni.com/flexrio. Contains product information and

data sheets for FlexRIO devices.

Verifying the System Requirements

To use the NI 5783, your system must meet certain requirements. For more information about

minimum system requirements, recommended system, and supported application development

environments (ADEs), refer to the readme, which is available on the software media or online

at ni.com/updates.

Unpacking

Caution To prevent ESD from damaging the devices, ground yourself using a

grounding strap or by holding a grounded object, such as your computer chassis.

1. Touch the antistatic package to a metal part of the computer chassis.

2. Remove each module from the package and inspect it for loose components or any other

sign of damage.

Caution Never touch the exposed pins of connectors.

Note Do not install a device if it appears damaged in any way.

3. Unpack any other items and documentation from the kit.

Store the devices in the antistatic package when they are not in use.

Preparing the Environment

Ensure that the environment you are using the NI 5783 in meets the following specifications.

Operating temperature (IEC 60068-2-1,

IEC 60068-2-2)

0 °C to 55 °C

Operating humidity (IEC 60068-2-56) 10% to 90% RH, noncondensing

4| ni.com | NI 5783 Getting Started Guide

Pollution Degree 2

Maximum altitude 2,000 m at 25 °C ambient temperature

Indoor use only.

Note Refer to the NI 5783 Specifications at ni.com/manuals for complete

specifications.

Caution Clean the hardware with a soft, nonmetallic brush. Make sure that the

hardware is completely dry and free from contaminants before returning it to

service.

Installing the NI 5783

Refer to the getting started guide for your FlexRIO FPGA module or Controller for FlexRIO

for instructions about how to install your FlexRIO system, including the NI 5783.

Confirming that Measurement & Automation

Explorer (MAX) Recognizes the Device

Use Measurement & Automation Explorer (MAX) to configure your NI hardware. MAX

informs other programs about which devices reside in the system and how they are configured.

MAX is automatically installed with FlexRIO Support.

1. Launch MAX by navigating to Start»All Programs»National Instruments»NI MAX or

by clicking the NI MAX desktop icon.

2. In the Configuration pane, double-click Devices and Interfaces to see the list of installed

devices. Installed devices appear under the name of their associated chassis.

3. (PXI and PXI Express devices only) Expand your Chassis tree item. MAX lists all

devices installed in the chassis. Your default device names may vary.

Note If you do not see your hardware listed, press <F5> to refresh the list of

installed devices. If the device is still not listed, power off the system, ensure

the device is correctly installed, and restart.

4. (Controllers for FlexRIO only) Your device appears under the Remote Devices section.

NI 5783 Getting Started Guide | © National Instruments | 5

Recommended Cables

NI recommends using the following cables to connect signals to the NI 5783.

Cable NI Part Number

HDBNC to SMA 769177-01

HDBNC to BNC 769028-01

Accessories

The NI 5783 can be used with the SCB-19 shielded desktop connector block.

Refer to the SCB-19 User Guide for information about how to connect and use the SCB-19

with the AUX I/O front panel connector on your NI 5783.

Related Information

AUX I/O Connector on page 8

Front Panel and Connector Pinouts

The following figure shows the front panel connectors for the NI 5783.

6| ni.com | NI 5783 Getting Started Guide

Device Front Panel Connector Signal Description

200 MS/s AO

100 MS/s AI

16-Bit AO-AI

NI 5783

INSTRUMENTS

NATIONAL

AUX

I/O

TRIG

CLK/

REF

AI 3

AI 2

AI 1

AI 0

AO 3

AO 2

AO 1

AO 0

AO 0 Analog input channel, 50 Ω, single-ended, DC-coupled

AO 1

AO 2

AO 3

AI 0 Analog output channel, 50 Ω, single-ended, DC-

coupled

AI 1

AI 2

AI 3

CLK/REF IN External Reference Clock or Sample Clock input

TRIG Trigger input and output channel

AUX I/O Digital I/O and PFI connector

Caution To avoid permanent damage to the NI 5783, disconnect all signals

connected to the NI 5783 before powering down the module, and connect signals

only after the adapter module has been powered on by the FlexRIO FPGA module or

Controller for FlexRIO.

Caution Connections that exceed any of the maximum ratings of any connector on

the NI 5783 can damage the device and the chassis. NI is not liable for any damage

resulting from such connections.

NI 5783 Getting Started Guide | © National Instruments | 7

AUX I/O Connector

Table 2. NI 5783 AUX I/O Connector Pin Assignments

AUX I/O Connector Pin Signal Signal Description

1 DIO Port 0 (0) Bidirectional single-ended (SE) digital I/O (DIO)

data channel.

2 GND Ground reference for signals.

3 DIO Port 0 (1) Bidirectional SE DIO data channel.

4 DIO Port 0 (2) Bidirectional SE DIO data channel.

5 GND Ground reference for signals.

6 DIO Port 0 (3) Bidirectional SE DIO data channel.

7 DIO Port 1 (0) Bidirectional SE DIO data channel.

8 GND Ground reference for signals.

9 DIO Port 1 (1) Bidirectional SE DIO data channel.

10 DIO Port 1 (2) Bidirectional SE DIO data channel.

11 GND Ground reference for signals.

12 DIO Port 1 (3) Bidirectional SE DIO data channel.

13 PFI 0 Bidirectional SE DIO data channel.

14 NC No connect.

15 PFI 1 Bidirectional SE DIO data channel.

16 PFI 2 Bidirectional SE DIO data channel.

17 GND Ground reference for signals.

18 +5 V +5 V power (10 mA maximum).

19 PFI 3 Bidirectional SE DIO data channel.

Caution The AUX I/O connector accepts a standard, third-party HDMI cable, but

the AUX I/O port is not an HDMI interface. Do not connect the AUX I/O port on the

8| ni.com | NI 5783 Getting Started Guide

NI 5783 to the HDMI port of another device. NI is not liable for any damage

resulting from such signal connections.

Related Information

Accessories on page 6

The NI 5783 can be used with the SCB-19 shielded desktop connector block.

Block Diagram

The following figure shows the NI 5783 block diagram and signal flow.

Figure 1. NI 5783 Block Diagram

CH0 AI

CH1 AI

40 MHz

Anti-Alias

ADA4932

Analog Input

85 MHz

Noise Filter

CH2 AI

CH3 AI

TRIG IN/OUT

CLOCK_REF IN

Buffered Trigger I/O To FPGA Interface

10/100 MHz CMOS Clock

CH0 A0 MCX

CH1 A0 MCX

CH2 A0 MCX

CH3 A0 MCX

–

40 MHz

Anti-Alias

ADA4932 85 MHz

Noise Filter

–

40 MHz

Anti-Alias

ADA4932 85 MHz

Noise Filter

–

40 MHz

Anti-Alias

ADA4932 85 MHz

Noise Filter

–

40 MHz AA LMH6702

–

40 MHz AA LMH6702

–

40 MHz AA LMH6702

–

40 MHz AA LMH6702

Analog Input

Clocking

100 MHz LVPECL CLK

100 MHz LVDS CLK

DACCLK/8 OSTR LVPECL 100 MHz

VCXO

Loop-Filter

(PLL)

Phase/Freq

Adjust DAC

Ch A+

DACCLK

DATACLK =

2”DACCLK

Ch A Ch B Ch C Ch D

Ch B+

Ch B+ DAC3484

QUAD 16-bit

1.25 GSPS DAC

AD9511

Clock Distribution

& PLL

1 W Max

Power Supplies

(100 MS/s Data Rate

Interpolate x8 for

Fixed Fdac of 800 MS/S

with Internal PLL)

Ch C+

Ch D+

Ch A+

HDMI DIO

Ch A+

DATACLK =

4”SAMPLECLK

SAMPLECLK

Ch B+

Ch B+ AD9653

QUAD 16-bit

125 MSPS ADC

(Clock at 100 MS/S)

Ch C+

Ch D+

Ch A1

Ch B0

Ch B1

Ch C0

Ch C1

Ch D0

Ch D1

A(15) A(13) A(11) A(9) Ch A0

A(14) A(12) A(10) A(8)

Typ: 4.6 W

Abs Max: 5.5 W

RSS Max: 5.3 W

+/– 4.5 V

+ 1.8 AVDD

+ 1.2 V

+ 3.8 V

+ 3.3 AVDD+ 1.8 DVDD

Inrush Limiter

400 MHz DDR (800 Mb/S)

DIO

16 BIT LVDS 400 MHz DDR (800 Mb/S)

400 MHz DDR (800 Mb/S)

FLEXRIO

SIGNAL REQ

ADC = 25

DAC = 50

PLL = 10

DIO? = 16

TOTAL = 103

+ 12 V

+ 3.3 V

OR + Vcco

+ VccoB

+ VccoA

TB_Ref_CLK/PXI_10

GPIO

VccoA = VccoB = Vcco = 2.5 V

Logic Diagram

The following diagram shows the NI 5783 logic layout.

Figure 2. NI 5783 Logic Layout

SPI Reg Report

Microblaze

User

Command

Interface

FAM

Status

Registers

I2C

Data ClockSample Clock

Data Clock 2x

1 Sample Per Channel

1/2 Samples Per Channel

Iserdes ADC

Capture

EEPROM

Phase

DAC

PLL

DAC

User Diagram

Oserdes

Iserdes

Oserdes DPA

Output

ADC

Clocking

Component-Level Intellectual Property (CLIP)

The LabVIEW FPGA Module includes component-level intellectual property (CLIP) for HDL

IP integration. FlexRIO devices support two types of CLIP: user-defined and socketed.

•User-defined CLIP allows you to insert HDL IP into an FPGA target, enabling VHDL

code to communicate directly with an FPGA VI.

•Socketed CLIP provides the same IP integration of the user-defined CLIP, but it also

allows the CLIP to communicate directly with circuitry external to the FPGA. Adapter

module socketed CLIP allows your IP to communicate directly with both the FPGA VI

and the external adapter module connector interface.

The FlexRIO adapter module ships with socketed CLIP items that add module I/O to the

LabVIEW project.

NI 5783 CLIP

This CLIP provides access to four 16-bit 100 MS/s analog input channels, four 16-bit analog

output channels (selectable between 100 MS/s and 200 MS/s), eight bidirectional DIO

channels, four bidirectional PFI channels, and the front panel trigger.

The analog output channels can be written two samples at a time in the Data Clock domain

with 4x interpolation, one sample at a time in the Data Clock domain with 8x interpolation, or

one sample at a time in the Data Clock 2x domain with 4x interpolation, according to the clock

mode selected.

10 | ni.com | NI 5783 Getting Started Guide

Inhaltsverzeichnis

Andere National Instruments Adapter Handbücher

National Instruments

National Instruments NI 6584R Bedienungsanleitung

National Instruments

National Instruments BNC-2110 Bedienungsanleitung

National Instruments

National Instruments 653 Series Bedienungsanleitung

National Instruments

National Instruments NI 9949 RJ-50 Bedienungsanleitung

National Instruments

National Instruments 1483R Bedienungsanleitung

National Instruments

National Instruments SC-205 Series Bedienungsanleitung

National Instruments

National Instruments 6584R Bedienungsanleitung

National Instruments

National Instruments NI 5762 Bedienungsanleitung

National Instruments

National Instruments BNC-2110 Bedienungsanleitung

National Instruments

National Instruments NI 1483 Bedienungsanleitung

National Instruments

National Instruments BNC-2115 Bedienungsanleitung

National Instruments

National Instruments NI 6535 Bedienungsanleitung

National Instruments

National Instruments NI 5791R Bedienungsanleitung

National Instruments

National Instruments NI 9147 Bedienungsanleitung

National Instruments

National Instruments NI-6589 Bedienungsanleitung

National Instruments

National Instruments SC-2072 Bedienungsanleitung

National Instruments

National Instruments SCXI-1349 Bedienungsanleitung

National Instruments

National Instruments BNC-2144 Bedienungsanleitung

National Instruments

National Instruments 68VHDCI-50F SSR 8 Bedienungsanleitung

National Instruments

National Instruments VXI-1000 Bedienungsanleitung

National Instruments

National Instruments PCI/PXI GIGABIT ETHERNET ADAPTERS Bedienungsanleitung

National Instruments

National Instruments NI-5752B Bedienungsanleitung

National Instruments

National Instruments DAQ SC-205X Series Bedienungsanleitung

National Instruments

National Instruments TC-2095 Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung