National Instruments SCXI-1362 Bedienungsanleitung
National Instruments™,NI
™,ni.com
™, and SCXI™are trademarks of National Instruments Corporation. Product and company names mentioned herein
are trademarks or trade names of their respective companies.
372735C-01 ©2000,2001 National Instruments Corp. All rights reserved. October 2001
INSTALLATION GUIDE
SCXI-1362 ADAPTER KIT
This guide explains how to unpack, install, and clean the SCXI-1362
adapter kit. With the SCXI-1362 adapter kit, you can connect the NI 4021
or NI 4060 to the following switch modules: SCXI-1160, SCXI-1161,
SCXI-1163R, SCXI-1190, SCXI-1191, or SCXI-1192.
The following connections are possible using the SCXI-1362 kit:
• Use the SH9MD-AUX cable to connect the digital communication
signals from the NI 4021 or NI 4060 to the AUX IN connector of the
SCXI-1362.
• In SCXI multichassis configurations, use a SH9MD-AUX cable to
extend the digital communication signals to the next SCXI chassis.
Note The maximum total cable length from the NI 4021 or NI 4060 to the farthest chassis
should not exceed 10 meters.
Checking The SCXI-1362 Adapter Kit Contents
Make sure the SCXI-1362 kit includes the following components:
❑One SCXI-1362 adapter
❑One SH9MD-AUX cable (round, 9-pin DIN connector)
❑Two small screws
Note If you ordered only the SCXI-1362 adapter, the kit should include the backplane
adapter but no cables.
You must provide the following:
❑SCXI chassis
❑SCXI-1160, SCXI-1161, SCXI-1163R, SCXI-1190, SCXI-1191,
and/or SCXI-1192
SCXI-1362 Adapter Kit Installation Guide 2 ni.com
❑SCXI controller (NI 4021 or NI 4060)
❑1/8 in. Phillips screwdriver
Unpacking
The SCXI-1362 is shipped in an antistatic package to prevent electrostatic
damage to the device. Electrostatic discharge can damage several
components on the device.
Caution Never touch the exposed pins of connectors.
To avoid such damage in handling the device, take the following
precautions:
•Ground yourself using a grounding strap or by holding a grounded
object.
•Touch the antistatic package to a metal part of your computer chassis
before removing the device from the package.
Remove the device from the package and inspect the device for loose
components or any sign of damage. Notify National Instruments if the
device appears damaged in any way. Do not install a damaged device
into your computer.
Store the SCXI-1362 in the antistatic envelope when not in use.
Safety Information
Cautions To meet EMC/EMI cooling and safety compliance requirements, the SCXI-1362
device must be installed in a chassis with the covers and chassis filler panels properly
installed.
Do not operate the device in an explosive atmosphere or where there may be flammable
gases or fumes.
Do not operate damaged equipment. The safety protection features built into this device
can become impaired if the device becomes damaged in any way. If the device is damaged,
turn the device off and do not use it until service-trained personnel can check its safety.
If necessary, return the device to National Instruments for service and repair to ensure that
its safety is not compromised.
Do not operate this equipment in a manner that contradicts the information specified in this
document. Misuse of this equipment could result in a shock hazard.
©National Instruments Corporation 3 SCXI-1362 Adapter Kit Installation Guide
Do not substitute parts or modify equipment. Because of the danger of introducing
additional hazards, do not install unauthorized parts or modify the device. Return the
device to National Instruments for service and repair to ensure that its safety features
are not compromised.
Yo u must insulate all of the signal connections to the highest voltage with which the
SCXI-1362 can come in contact.
Connections, including power signals to ground and vice versa, that exceed any of the
maximum signal ratings on the SCXI device can create a shock or fire hazard, or can
damage any or all of the boards connected to the SCXI chassis, the host computer, and the
SCXI device. National Instruments is not liable for any damages or injuries resulting from
incorrect signal connections.
Clean the module and accessories by brushing off light dust with a soft non-metallic brush.
Remove other contaminants with a stiff non-metallic brush. The unit must be completely
dry and free from contaminants before returning it to service.
The adapter must be used with a UL-listed SCXI chassis.
Installing the SCXI-1362 Adapter Kit
Refer to Figure 1 when installing the SCXI-1362 adapter kit. To install the
SCXI-1362 kit, complete the following:
1. Power off the computer and SCXI chassis.
2. Install the SCXI modules in the SCXI chassis following the
instructions in the module user manuals. When installed, the back
of the SCXI module is not flush with the back of the SCXI chassis.
3. Install the SCXI-1362 adapter through the chassis into the rear of the
SCXI module. When installed, the SCXI-1362 adapter is flush with the
back of the SCXI chassis. Refer to Figure 1.
4. Using the two screws included in the kit, secure the SCXI-1362
adapter into the threaded strips in the rear of the SCXI chassis.
5. Connect one end of the SH9MD-AUX cable to the AUX IN connector
of the SCXI-1362 adapter.
6. Connect the other end of the cable to the AUX I/O connector of the
switch controller.
SCXI-1362 Adapter Kit Installation Guide 4 ni.com
Figure 1. Installing the SCXI-1362 Kit
1 SCXI Chassis
2 SCXI-1362 Adapter
3SmallScrew
4 AUX IN Connector
5 AUX OUT Connector
6 SH9MD-AUX Cable
FUSE
PULL
1
6
2
3
3
LV ANALOG
FROM
DMM
OR
PREVIOUS
CHASSIS
TO NEXT
CHASSIS
AUX
IN
AUX
OUT
4
5
©National Instruments Corporation 5 SCXI-1362 Adapter Kit Installation Guide
Installing the SCXI-1362 in a Multichassis System
Refer to Figure 2 when installing the SCXI-1362 adapter kit in a
multichassis system. To install the SCXI-1362 adapter kit in a
multichassis system, complete the following:
1. Repeat steps 1 through 5 of the Installing the SCXI-1362 Adapter Kit
section.
2. Connect the other end of the SH9MD-AUX cable to the AUX OUT
connector of the previously installed SCXI-1362 adapter.
3. Repeat steps 1 and 2 for any additional SCXI-1362 adapter kits.
Figure 2. Installing SCXI-1362s in a Multichassis System
1 Chassis 1
2 SCXI-1362 Adapter
3 SH9MD-AUX Cables
4 Chassis 3
5 NI 4021 or NI 4060
6 Chassis 2
5
1
TO NEXT
CHASSIS
FROM
DMM
OR
PREVIOUS
CHASSIS
AUX
IN
AUX
OUT
LVANALOG
FROM
DMM
OR
PREVIOUS
CHASSIS
TO NEXT
CHASSIS
AUX
IN
AUX
OUT
LVANALOG
FROM
DMM
OR
PREVIOUS
CHASSIS
TO NEXT
CHASSIS
AUX
IN
AUX
OUT
6
4
3
2
2
2
SCXI-1362 Adapter Kit Installation Guide 6 ni.com
Safety
Designed in accordance with IEC 61010-1, EN 61010-1, UL 3111-1, and
CAN/CSA C22.2 No. 1010.1 for electrical measuring and test equipment.
For use at altitudes up to 2000 meters.
Installation category II1
Pollution degree 2
Electromagnetic Compatibility
EMC/EMI ...............................................CE, C-Tick, and FCC Part 15
(Class A) Compliant
Electrical emissions ................................EN 55011 Class A at 10 m
FCC Part 15A above 1 GHz
Electrical immunity ................................Evaluated to EN 61326-1:1997
A1:1998, Table 1
Note For full EMC and EMI compliance, you must operate this device with shielded
cabling. See the Declaration of Conformity (DoC) for this product for any additional
regulatory compliance information. To obtain the DoC for this product, click
Declaration of Conformity at ni.com/hardref.nsf/. This Web site lists the DoCs by
product family. Select the appropriate product family, followed by your product, and a link
to the DoC (in Adobe Acrobat format) appears. Click the Acrobat icon to download or read
the DoC.
1Category II refers to local level distribution, such as that provided by a standard wall outlet.
Inhaltsverzeichnis
Andere National Instruments Adapter Handbücher
National Instruments
National Instruments PCI/PXI ETHERNET ADAPTERS Bedienungsanleitung
National Instruments
National Instruments NI 9149 Bedienungsanleitung
National Instruments
National Instruments NI-6589 Bedienungsanleitung
National Instruments
National Instruments NI 653x Bedienungsanleitung
National Instruments
National Instruments VXI-1000 Bedienungsanleitung
National Instruments
National Instruments SC-2072 Bedienungsanleitung
National Instruments
National Instruments NI 1483 Bedienungsanleitung
National Instruments
National Instruments 5783 Bedienungsanleitung
National Instruments
National Instruments NI 6535 Bedienungsanleitung
National Instruments
National Instruments SC-2042-RTD Bedienungsanleitung
National Instruments
National Instruments BNC-2142 Bedienungsanleitung
National Instruments
National Instruments NI-5752B Bedienungsanleitung
National Instruments
National Instruments 6584R Bedienungsanleitung
National Instruments
National Instruments SC-205 Series Bedienungsanleitung
National Instruments
National Instruments NI 9147 Bedienungsanleitung
National Instruments
National Instruments REM-11180 Bedienungsanleitung
National Instruments
National Instruments NI 5791R Bedienungsanleitung
National Instruments
National Instruments USB-6001 Bedienungsanleitung
National Instruments
National Instruments 68M-50F STEP Bedienungsanleitung
National Instruments
National Instruments 653 Series Bedienungsanleitung
