National Instruments IMAQ SCB-100 Bedienungsanleitung

IMAQ

™

is a trademark of National Instruments Corporation. Product and company names mentioned herein are trademarks or trade names of their

respective companies.

321950B-01

INSTALLATION GUIDE

IMAQ SCB-100 CONNECTOR BLOCK AND

IMAQ D100100 CABLE

This guide describes how to connect and use the IMAQ SCB-100 100-pin

shielded connector block with 100-pin digital image acquisition (IMAQ)

products and the IMAQ D100100 cable.

Warning Use the D100100 cable with IMAQ digital devices only. Also, do not use data

acquisition (DAQ) cables with IMAQ digital devices. Using the D100100 cable

withotherdevicesor DAQcableswithIMAQ digital devicesmayresult indamages

to your device or your computer. National Instruments is NOT liable for any

damages or injuries resulting from improper use or connection.

Introduction

The IMAQ SCB-100 100-pin shielded connector block is a shielded board

with 100 screw terminals that connects to the IMAQ PCI-1424 or other

products using a 0.050 series shielded D-type I/O connector.

The terminal block has 100 screw terminals for easy connection to signal

wires.When youuse theIMAQSCB-100 100-pinshielded connectorblock

with the IMAQ PCI-1424, set the switches as shown in the Switch Settings

section to obtain a generic 100-screw terminal connector block. The IMAQ

SCB-100 also has a strain-relief bar for securing signal wires or cables.

What You Need to Get Started

To install your IMAQ D100100 cable, you will need the following:

❑IMAQ SCB-100 100-pin shielded connector block

❑IMAQ D100100 cable

❑IMAQ SCB-100 Connector Block and IMAQ D100100 Cable

Installation Guide

IMAQ SCB-100 and D100100 Installation Guide 2

National Instruments Corporation

❑IMAQ SCB-100 quick reference label (included with your IMAQ

SCB-100 kit)

❑Your IMAQ device and documentation

❑Your computer

❑Your digital camera

❑No. 1 and 2 Phillips-head screwdrivers

❑0.125 in. flathead screwdriver

❑Long-nose pliers

❑Wire cutters

❑Wire insulation strippers

❑Soldering iron and solder

❑Resistors and capacitors (specific to your application)

Switch Settings

Before you connect your IMAQ D100100 cable to the IMAQ SCB-100

connector block, you must change the IMAQ SCB-100 switch settings to

the generic screw terminals switch configuration, as shown in Figure 1.

This setting change disconnects the IMAQ SCB-100 temperature sensor

and accessory grounds.

Figure 1. IMAQ SCB-100 Switch Settings for IMAQ

S6S5S4

National Instruments Corporation 3 IMAQ SCB-100 and D100100 Installation Guide

IMAQ Quick Reference Label

A quick reference label is included to show switch configuration and define

screw terminal pinouts for your IMAQ digital device. Attach the quick

reference label to the connector block’s inside cover for quick reference.

Installation

As shown in Figure 2, attach one end of the D100100 cable to your IMAQ

deviceand attach theotherto theIMAQ SCB-100 connectorblock. Tighten

thumbscrews as necessary.

Figure 2. Connecting the D100100 Cable to Your IMAQ Device and IMAQ SCB-100

1 IMAQ Device 2Thumbscrews 3 IMAQ D100100 Cable 4 IMAQ SCB-100

232

IMAQ SCB-100 and D100100 Installation Guide 4

National Instruments Corporation

Signal Connections

The following warnings contain important safety information concerning

hazardous voltages and terminal blocks.

Warning Avoid live circuits. To avoid electrical shock, do not remove equipment covers or

shieldsunless youare qualifiedto doso. Ifsignal wires areconnected tothe IMAQ

SCB-100, dangerous voltages may exist even when the equipment is turned off.

Before removing the cover, disconnect the AC power or any live circuit from the

terminal block.

Warning The chassis ground terminals on your IMAQ SCB-100 are for grounding

high-impedance sources such as a floating source (1 mA maximum). Do not use

these terminals as safety earth grounds.

Warning Do not connect high voltages (

≥≥

42 Vrms). National Instruments is NOT liable for

any damages or injuries resulting from improper use or connection.

To connect the signal to the IMAQ SCB-100, perform the following steps:

1. Disconnect the 100-pin cable from the IMAQ SCB-100, if connected.

2. Remove the grounding screws on either side of the top cover with a

No. 1 Phillips-head screwdriver. Open the top cover.

3. Configure switches, as explained in the Switch Settings section in this

guide.

4. Adjust the strain-relief hardware.

• Loosen the strain-relief screws with a No. 2 Phillips-head

screwdriver and slide the signal wires through the front panel

strain-relief opening.

• If you are connecting multiple signals, removethe top strain-relief

bar.

5. Add insulation or padding if necessary.

6. Connect the wires to the screw terminals by stripping 1/4 in. of

insulation, inserting the wires into the green terminals, and tightening

the screws.

7. Reinstall strain-relief (if removed) and tighten the strain-relief screws.

8. Close the top cover.

9. Reinsert the grounding screws to ensure proper shielding.

10. Connect the terminal block to the 100-pin connector.

National Instruments Corporation 5 IMAQ SCB-100 and D100100 Installation Guide

Removing the Board

You can remove the board from its housing to solder components into

place. To remove the board, perform the following steps:

1. Disconnect the 100-pin cable from the IMAQ SCB-100, if connected.

2. Remove the grounding screws on either side of the top cover with a

No. 1 Phillips-head screwdriver.

3. Open the top cover.

4. Loosen the strain-relief screws with a No. 2 Phillips-head screwdriver.

5. Remove the signal wires from the screw terminals.

6. Remove the board mount screws and 100-pin connector screws.

7. Tilt the board up and pull it out of the enclosure.

Figure 3 shows the IMAQ SCB-100 terminal block parts locator diagram.

IMAQ SCB-100 and D100100 Installation Guide 6

National Instruments Corporation

Figure 3. IMAQ SCB-100 Terminal Block Parts Locator Diagram

1 Cold-Junction Compensation

Temperature Sensor (Not Used)

2 Product Name

3 Switches S4, S5, and S6

4 100-Pin I/O Connector

5 Signal Accessory Power LED

(Not Used)

6 Switches S1, S2, and S3

7 Serial Number

8 Assembly Number

9 Screw Terminals

10 Breadboard Area

11 Board Mount Screws

12 Jumper Trace (cut to disconnect)

National Instruments Corporation 7 IMAQ SCB-100 and D100100 Installation Guide

Adding Components to the IMAQ SCB-100

Printed Circuit Board

Some applications may require you to make modifications to the printed

circuit board, usually in the form of adding components or cutting jumpers.

Follow these guidelines when modifying the IMAQ SCB-100 printed

circuit board:

• Use a low-wattage soldering iron (20 to 30 W) when soldering to the

board.

• Use vacuum-type tools to desolder on the IMAQ SCB-100. Use care

when desoldering to avoid damaging component pads.

• Use only rosin-core, electronic-grade solder. Acid-core solder can

damage the printed circuit board and components.

To make signal modifications easier, jumper traces are located next to each

analog screw terminal. These jumper traces can be cut to disconnect the

signal from the screw terminal. Refer to Figure 3 for more detail.

Specifications

This section lists the IMAQ SCB-100 specifications. These ratings are

typical at 25 °C unless otherwise stated.

General

Number of screw terminals.....................101 (includes one no-connect).

All I/O signals are available at

screw terminals

Physical

Box dimensions (including feet).............19.6 by 15.2 by 4.6 cm

(7.7 by 6.0 by 1.8 in.)

I/O connectors.........................................One 100-pin male 0.050 series

shielded D type connector

Operating Environment

Component temperature .........................0 to 70 °C

Relative humidity ...................................5% to 90% noncondensing

Storage Environment

Temperature............................................–55 to 125 °C

Relative humidity ...................................5% to 90% noncondensing

Andere Handbücher für IMAQ SCB-100

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere National Instruments Kabel und Steckverbinder Handbücher

National Instruments

National Instruments PXI-2530B Bedienungsanleitung

National Instruments

National Instruments SCXI-1355 Bedienungsanleitung

National Instruments

National Instruments NI-XNET LIN Bedienungsanleitung

National Instruments

National Instruments CB-27 Bedienungsanleitung

National Instruments

National Instruments BNC-2121 Bedienungsanleitung

National Instruments

National Instruments SCXI-1348 Bedienungsanleitung

National Instruments

National Instruments SH160DIN-4XDB50F-2A Bedienungsanleitung

National Instruments

National Instruments 9923 Bedienungsanleitung

National Instruments

National Instruments IMAQ A8014 Bedienungsanleitung

National Instruments

National Instruments SCXI-1356 Bedienungsanleitung

National Instruments

National Instruments FIELDPOINT CFP-CB-1 Bedienungsanleitung

National Instruments

National Instruments IMAQ SCB-100 Bedienungsanleitung

National Instruments

National Instruments SCB-68 Bedienungsanleitung

National Instruments

National Instruments LFH200 Bedienungsanleitung

National Instruments

National Instruments NI 9924 Bedienungsanleitung

National Instruments

National Instruments SCXI-1345 Bedienungsanleitung

National Instruments

National Instruments GMCT20 Bedienungsanleitung

National Instruments

National Instruments IMAQ A8020 Bedienungsanleitung

National Instruments

National Instruments IMAQ A2514 Bedienungsanleitung

National Instruments

National Instruments 9212 Handbuch

National Instruments

National Instruments CB-50 Bedienungsanleitung

National Instruments

National Instruments IMAQ D100 Bedienungsanleitung

National Instruments

National Instruments PXI-1042HVDC Bedienungsanleitung

National Instruments

National Instruments SCXI-1342 PC-LPM-16 Bedienungsanleitung

Beliebte Kabel und Steckverbinder Handbücher anderer Marken

Philips

Philips SWA6310 Bedienungsanleitung

StarTech.com

StarTech.com CRJ4550PK Bedienungsanleitung

Nohau

Nohau EMUL-IP2K-PC Bedienungsanleitung

Foxun

Foxun SX-SP144E-HD4K2K Bedienungsanleitung

Philips

Philips SWA3305W Bedienungsanleitung

opticis

opticis Stretch DVIM1-1P0x Bedienungsanleitung

Volkswagen

Volkswagen VAS 6558A Bedienungsanleitung

NEXIBO

NEXIBO N-13 Bedienungsanleitung

CYP

CYP PU-1H3HBTL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1784-u2dhp Bedienungsanleitung

Global Caché

Global Caché Flex Link Blaster Bedienungsanleitung

Hauppauge

Hauppauge USB-Live2 Bedienungsanleitung

Fenix

Fenix MPSV 15 Bedienungsanleitung

BEGA

BEGA 71 085 Bedienungsanleitung

Tesla

Tesla HPWC Bedienungsanleitung

GAMERON

GAMERON LUXURY TV CABLE Bedienungsanleitung

molex

molex Milli-Grid Dual row 87568 Series Bedienungsanleitung

Burndy

Burndy Continental Industries thermOweld CRE-7 Bedienungsanleitung