National Instruments SCXI-1348 Bedienungsanleitung

NATIONAL

INSTRUMENTS @

The Sofrware k the Instrument @

SCXI-1348 DIO-32F

Cable Assembly

Installation Guide

Part Number 320620-01

This guide describes how to install the SCXI-1348 cable assembly between an SCXI module and I

an AT-DIO-32F, MC-DIO-32F, or NB-DIO-32F data acquisition board. In addition to the

SCXI-1348 kit contents, you will also need an SCXI chassis, an SCXI module, a computer, a

DIO-32F data acquisition board, and a small flathead screwdriver.

Introduction

With the SCXI-1348 cable assembly, you can connect a digital I/O SCXI module to your

DIO-32F data acquisition board. The DIO-32F works with the SCXI-1160, SCXI-1161,

SCXI- 1162, and SCXI- 1163 modules.

If you have a newly released module or a data acquisition board other than a DIO-32F, contact

National Instruments for information on your cable needs.

The SCXI-1348 cable assembly consists of an adapter board and an NB4 50-conductor shielded

ribbon cable that connects the adapter board to a DIO-32F data acquisition board. The adapter

board converts the signals from the DIO-32F I/O connector to the pinout that a digital SCXI

module rear signal connector uses. To extend the unconverted signals of the DIO-32F to another

module or to an SCXI-1180 feedthrough panel, you can use the male breakout connector that is

on the center of the adapter board.

What Your Kit Should Contain

The contents of the SCXI-1348 cable assembly kit are as follows:

Kit Name and

Part Number Component I Component

Part Number I

SCXI- 1348 Cable

Assembly (776574-48) Cable adapter

Two small screws

1 m NB4 shielded 50-pin ribbon cable.

SCXI-1348 DIO-32F Cable Assembly

Installation Guide

182252-01

742413-01

180554-10

320620-01

If your kit is missing any of the components, contact National Instruments.

0 1993 National Instruments

Corporation.

Installation Procedure

Figure 1illustrates thecomponents of your SCXI system.

SCXI-1348SCXI-1348

Cable AdapterCable Adapter

erer

~~~~~~-~~~~~~~-~

77 (optional connection)(optional connection)

77 DIO-32F Data Acquisition BoardDIO-32F Data Acquisition Board

gr SCXI Modulegr SCXI Module

Figure 1. Connecting the SCXI-1348 to Your DIO-32F Data Acquisition Board

andSCXI Module

Perform thefollowing stepsto install theSCXI-1348 cableadapter:

1. Turn off the power to your computer andtheSCXI chassis.

2. Install your SCXI module in the SCXI chassis,following the instructions in your module

usermanual.

3. Plug thefront connector of theSCXI-1348 into therearsignal connector of the SCXI

module. A comer of the adapterboardwill entertheupperboard guide of the chassis.

4. Securethe SCXI-1348 adapterboardby screwing the two screws through therearpanel of

theadapterboard andinto the threadedstrips in therearof the SCXI chassis.

5. Connect oneendof the 50-pin shielded ribbon cable to the adapterboard rearconnector.

6. Install your dataacquisition boardin aslot in your computer, following theinstructions in

your dataacquisition boardusermanual.

7. Connect the looseend of theshielded ribbon cable to theI/O connector onthe data

acquisition board asshown in Figure 2.

XXI-1348 Cable Assembly Installation Guide 2 0 National Instruments Corporation

~-~

Shielded Ribbon Cable

DIO-32F Data Acquisition Board

Figure 2. Cable to I/O Connector Connection

Thefinished installation should look like Figure 3.

Figure 3. Installed Cable

The following table lists the way that theSCXI-1348 translatespins from aDIO-32F board to the

SCXI module.

0 National Instruments Corporation XXI-1348 Cable Assembly Znstallation Guide

SCXI- 1348”Pin Translations

DIO-32F Rear

Connector Pin

;

1011

1516

17,19*

21,23*

25,26*

28,30*

32,34*

iti

z7”

DIO-32F Signal

Name

DIODl

DIOD4

DIOD3

DIODO

DIOD6

DIOD7

DIOD2

DIODSDIOCS

DIOC7DIOC3

DIOC 1

DIOC2

DIOCO

DIOC6bIOC4

DIGGND

ACK2

IN2

OUT2

REQ2

ACKl

IN1

OUT1

REQl

DIOA4

DIOA6

DIOAO

DIOA2DIOAl

DIOA3

DIOA7

DIOAS

DIOBS

DIOB2

DIOB7

DIOB6

DIOBO

DIOB3

DIOB4

DIOB 1

Module

Connector Pin

385

;

yy;tr

10: 12*

14,16*

50*

;;

4345

z7’

;;

*All DIG GND pins are connected to each other on the SCXI-1348 adapter board.

SCXI-1348 Cable Assembly Installation Guide 4 0 National Znstrumnts Corporation

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere National Instruments Kabel und Steckverbinder Handbücher

National Instruments

National Instruments SH160DIN-4XDB50F-2A Bedienungsanleitung

National Instruments

National Instruments CB-50 Bedienungsanleitung

National Instruments

National Instruments IMAQ A2514 Bedienungsanleitung

National Instruments

National Instruments LFH200 Bedienungsanleitung

National Instruments

National Instruments IMAQ D100 Bedienungsanleitung

National Instruments

National Instruments IMAQ A8014 Bedienungsanleitung

National Instruments

National Instruments IMAQ SCB-100 Bedienungsanleitung

National Instruments

National Instruments 9212 Handbuch

National Instruments

National Instruments NI-XNET CAN HS/FD Bedienungsanleitung

National Instruments

National Instruments IMAQ D6826 Bedienungsanleitung

National Instruments

National Instruments NI-XNET LIN Bedienungsanleitung

National Instruments

National Instruments PXI-2530B Bedienungsanleitung

National Instruments

National Instruments GMCT20 Bedienungsanleitung

National Instruments

National Instruments TB-2676 Bedienungsanleitung

National Instruments

National Instruments BNC-2121 Bedienungsanleitung

National Instruments

National Instruments NI SCB-68A Bedienungsanleitung

National Instruments

National Instruments BNC-9920 Bedienungsanleitung

National Instruments

National Instruments SCXI-1355 Bedienungsanleitung

National Instruments

National Instruments PXI-1031DC Bedienungsanleitung

National Instruments

National Instruments IMAQ A8020 Bedienungsanleitung

National Instruments

National Instruments IMAQ D100DAL Bedienungsanleitung

National Instruments

National Instruments SCXI-1356 Bedienungsanleitung

National Instruments

National Instruments SCXI-1353 Bedienungsanleitung

National Instruments

National Instruments SH160DIN-3XDB50F Bedienungsanleitung

Beliebte Kabel und Steckverbinder Handbücher anderer Marken

Philips

Philips SWA6310 Bedienungsanleitung

StarTech.com

StarTech.com CRJ4550PK Bedienungsanleitung

Nohau

Nohau EMUL-IP2K-PC Bedienungsanleitung

Foxun

Foxun SX-SP144E-HD4K2K Bedienungsanleitung

Philips

Philips SWA3305W Bedienungsanleitung

opticis

opticis Stretch DVIM1-1P0x Bedienungsanleitung

Volkswagen

Volkswagen VAS 6558A Bedienungsanleitung

NEXIBO

NEXIBO N-13 Bedienungsanleitung

CYP

CYP PU-1H3HBTL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1784-u2dhp Bedienungsanleitung

Global Caché

Global Caché Flex Link Blaster Bedienungsanleitung

Hauppauge

Hauppauge USB-Live2 Bedienungsanleitung

Fenix

Fenix MPSV 15 Bedienungsanleitung

BEGA

BEGA 71 085 Bedienungsanleitung

Tesla

Tesla HPWC Bedienungsanleitung

GAMERON

GAMERON LUXURY TV CABLE Bedienungsanleitung

molex

molex Milli-Grid Dual row 87568 Series Bedienungsanleitung

Burndy

Burndy Continental Industries thermOweld CRE-7 Bedienungsanleitung