National Instruments 9923 Bedienungsanleitung

USER GUIDE AND SPECIFICATIONS

NI 9923

37-Pin DSUB to Screw-Terminal Connector Block

ni.com/manuals

DeutschFrançais

2|ni.com |NI 9923 User Guide and Specifications

This user guide describes the features of the National

Instruments 9923 DSUB to Screw-Terminal Connector Block. You

can use the NI 9923 to create custom cables for C Series modules

that use 37-pin DSUB connectors.

Note The NI 9923 is compatible with NI Compact

FieldPoint devices.

Caution Do not remove the NI 9923 circuit board from

the enclosure.

Caution Do not supply hazardous voltages

(>30 Vrms/42 Vpk/60 VDC) to the NI 9923.

Caution Before using the NI 9923, read the Operating

Instructions and Specifications for the C Series module to

ensure compliance with safety, EMC, and environmental

regulations.

NI 9923 User Guide and Specifications |© National Instruments |3

Connecting the NI 9923

The NI 9923 provides connections for C Series 37-pin DSUB

modules.

Figure 1. NI 9923 Terminal Assignments

Pin 20

Pin 19 Pin 37

Pin 1

4|ni.com |NI 9923 User Guide and Specifications

Connecting the Signals

To wire the NI 9923, complete the following steps while referring

to Figure 2.

Note When using shielded wires or cable, use the

SH terminal on the NI 9923 to terminate the shields.

1. Loosen the captive screws and remove the top cover.

2. Prepare the screw-terminal wire by stripping the insulation.

Refer to the Specifications section for more information on

screw-terminal wiring.

3. Insert the stripped end of the wire fully into the appropriate

terminal. Make sure no exposed wire extends past the screw

terminal.

4. Secure the connection by tightening the screw for the terminal.

Refer to the Specifications section for information on

screw-terminal torque.

5. Route the wire to the NI 9923 opening.

6. Remove slack in the NI 9923 wiring and secure the wires or

cable by threading a zip tie through the two strain relief holes

on the NI 9923 opening.

NI 9923 User Guide and Specifications |© National Instruments |5

7. Reinstall the top cover on the NI 9923 and tighten the

four captive screws.

Figure 2. NI 9923 Parts Locator Diagram

1 Captive Screws

2 Top Cover

3 Terminals

4 Strain Relief Holes

5 Jackscrews

6|ni.com |NI 9923 User Guide and Specifications

Installing the NI 9923

Connect the NI 9923 to the 37-pin DSUB connector on the module

as shown in Figure 3. Tighten the two jackscrews on the NI 9923

to hold it securely in place. Do not overtighten the jackscrews.

Refer to Figure 2 for the location of the jackscrews.

Figure 3. Installing the NI 9923

NI 9923 User Guide and Specifications |© National Instruments |7

Specifications

The following specifications are typical unless otherwise noted.

Maximum voltage ............................. 30 Vrms/42 Vpk/60 VDC

Operating temperature ...................... –40 °C to 70 °C

Maximum current rating by temperature

Pins 9, 10, 19, 28, & 29

–40 °C to 55 °C.................... ≤5 A

56 °C to 70 °C...................... ≤4 A

Pins 1–8, 11–18, 20–27, & 30–37

–40 °C to 55 °C.................... ≤1 A

56 °C to 70 °C...................... ≤1 A per channel,

≤16 A aggregate

Screw-terminal wiring ...................... 16 AWG to 26 AWG copper

conductor wire with 4.5 mm

(0.18 in.) of insulation

stripped from the end

Torque for screw terminals ............... 0.4 N · m max

(3.4 lb · in. max)

Weight............................................... 82 g (2.9 oz)

375923C-01 Apr12

LabVIEW, National Instruments, NI, ni.com, the National Instruments corporate logo, and the Eagle logo are

trademarks of National Instruments Corporation. Refer to the Trademark Information at ni.com/trademarks

for other National Instruments trademarks. Other product and company names mentioned herein are trademarks or

trade names of their respective companies. For patents covering National Instruments products/technology, refer

to the appropriate location: Help»Patents in your software, the patents.txt file on your media, or the

National Instruments Patent Notice at ni.com/patents. Refer to the Export Compliance Information at

ni.com/legal/export-compliance for the National Instruments global trade compliance policy and

how to obtain relevant HTS codes, ECCNs, and other import/export data.

Where to Go for Support

The National Instruments Web site is your complete resource for

technical support. At ni.com/support you have access to

everything from troubleshooting and application development

self-help resources to email and phone assistance from

NI Application Engineers.

National Instruments corporate headquarters is located at

11500 North Mopac Expressway, Austin, Texas, 78759-3504.

National Instruments also has offices located around the world to

help address your support needs. For telephone support in the

United States, create your service request at ni.com/support and

follow the calling instructions or dial 512 795 8248. For telephone

support outside the United States, visit the Worldwide Offices

section of ni.com/niglobal to access the branch office Web

sites, which provide up-to-date contact information, support phone

numbers, email addresses, and current events.

Inhaltsverzeichnis

Andere National Instruments Kabel und Steckverbinder Handbücher

National Instruments

National Instruments IMAQ SCB-100 Bedienungsanleitung

National Instruments

National Instruments NI SCB-68A Bedienungsanleitung

National Instruments

National Instruments IMAQ SCB-100 Bedienungsanleitung

National Instruments

National Instruments BNC-2120 Bedienungsanleitung

National Instruments

National Instruments IMAQ D6826 Bedienungsanleitung

National Instruments

National Instruments SCXI-1348 Bedienungsanleitung

National Instruments

National Instruments SCXI-1342 PC-LPM-16 Bedienungsanleitung

National Instruments

National Instruments PXI-1042HVDC Bedienungsanleitung

National Instruments

National Instruments SCB-68 Bedienungsanleitung

National Instruments

National Instruments IMAQ SCB-100 Bedienungsanleitung

National Instruments

National Instruments CB-27 Bedienungsanleitung

National Instruments

National Instruments NI 9924 Bedienungsanleitung

National Instruments

National Instruments SCXI-1345 Bedienungsanleitung

National Instruments

National Instruments SCXI-1353 Bedienungsanleitung

National Instruments

National Instruments SCXI-1356 Bedienungsanleitung

National Instruments

National Instruments PXI-1031DC Bedienungsanleitung

National Instruments

National Instruments SH160DIN-4XDB50F-2A Bedienungsanleitung

National Instruments

National Instruments BNC-9920 Bedienungsanleitung

National Instruments

National Instruments IMAQ D100 Bedienungsanleitung

National Instruments

National Instruments SH6850 Bedienungsanleitung

National Instruments

National Instruments SCXI-1355 Bedienungsanleitung

National Instruments

National Instruments IMAQ D100DAL Bedienungsanleitung

National Instruments

National Instruments GMCT20 Bedienungsanleitung

National Instruments

National Instruments SH160DIN-3XDB50F Bedienungsanleitung

Beliebte Kabel und Steckverbinder Handbücher anderer Marken

Philips

Philips SWA6310 Bedienungsanleitung

StarTech.com

StarTech.com CRJ4550PK Bedienungsanleitung

Nohau

Nohau EMUL-IP2K-PC Bedienungsanleitung

Foxun

Foxun SX-SP144E-HD4K2K Bedienungsanleitung

Philips

Philips SWA3305W Bedienungsanleitung

opticis

opticis Stretch DVIM1-1P0x Bedienungsanleitung

Volkswagen

Volkswagen VAS 6558A Bedienungsanleitung

NEXIBO

NEXIBO N-13 Bedienungsanleitung

CYP

CYP PU-1H3HBTL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1784-u2dhp Bedienungsanleitung

Global Caché

Global Caché Flex Link Blaster Bedienungsanleitung

Hauppauge

Hauppauge USB-Live2 Bedienungsanleitung

Fenix

Fenix MPSV 15 Bedienungsanleitung

BEGA

BEGA 71 085 Bedienungsanleitung

Tesla

Tesla HPWC Bedienungsanleitung

GAMERON

GAMERON LUXURY TV CABLE Bedienungsanleitung

molex

molex Milli-Grid Dual row 87568 Series Bedienungsanleitung

Burndy

Burndy Continental Industries thermOweld CRE-7 Bedienungsanleitung