National Instruments FieldPoint FP-1300 Bedienungsanleitung

FieldPoint

1FP-1300 Quick Start Guide

National Instruments Corporation

FP-1300 FieldPoint Quick Start Guide

What You Need

to Get Set Up

• FP-1300 network module

• DIN rail mounting hardware

• Terminal base(s) and I/O module(s)

• 10–30 VDC power supply to power

the CAN bus

• 11–30 VDC power supply to power

the FieldPoint bus

• Accessories: shielded twisted-pair

cable, Combicon-style connector,

flathead screwdriver

• Optional accessories: two 120 Ω

resistors

• Installed and configured NI-CAN

card

IIIInn

nnss

ssttttaa

aallllllll tttthh

hhee

ee NN

NNee

eettttww

wwoo

oorr

rrkk

kk MM

MMoo

oodd

dduu

uullllee

Mount the module on a DIN rail.

A. Unlock rail clip.

FP-1300 Quick Start Guide ni.com

B. Hook lip on back of module onto top of DIN rail, press down, and snap into place.

C. Slide module into position and lock rail clip.

NNOO

OOTT

TTEE

EE Do not use spliced DIN rails. Use only a single DIN rail.

3FP-1300 Quick Start Guide

National Instruments Corporation

IIIInn

nnss

ssttttaa

aallllllll tttthh

hhee

ee TT

TTee

eerr

rrmm

mmiiiinn

nnaa

aallll BB

BBaa

aass

ssee

ee((((ss

ss))))

CCAA

AAUU

UUTT

TTIIIIOO

OONN

NN Connect the terminal bases to the network module before applying power

to the module. Do not connect or disconnect terminal bases while power is applied to

the network module.

A. Unlock rail clip.

B. Press base onto rail.

FP-1300 Quick Start Guide ni.com

C. Slide into position and lock the rail clip. Be careful not to bend any pins.

D. Repeat for each terminal base, up to nine for each network module in most cases. You can

use one or two extender cables (which you can order separately) if the FieldPoint bank is too

long for the available space.

E. Place protective cover on last base, and install rail locks at each end.

5FP-1300 Quick Start Guide

National Instruments Corporation

IIIInn

nnss

ssttttaa

aallllllll tttthh

hhee

ee IIII////OO

OO MM

MMoo

oodd

dduu

uullllee

ee((((ss

ss))))

It does not matter where you install each I/O module, except in the following cases:

• If you plan to cascade power between any I/O modules using the V and C terminals, those

modules should be grouped together.

• For more accurate measurements, place thermocouple modules away from heat sources,

including network modules or relay modules.

A. Align slots on the module with the guide rails on the base, and press the module onto base

until the terminal base latch locks the module in place.

B. Repeat for each I/O module.

CCAA

AAUU

UUTT

TTIIIIOO

OONN

NN Cascading power defeats isolation.

FP-1300 Quick Start Guide ni.com

CCoo

oonn

nnffffiiiigg

gguu

uurr

rree

ee tttthh

hhee

ee AA

AArr

rrbb

bbiiiittttrr

rraa

aattttiiiioo

oonn

nn IIIIDD

The FP-1300 ships with the standard base arbitration ID 0x0. The FP-1300 sequentially allocates

the I/O channel arbitration IDs from the base arbitration ID of the FP-1300. If you are not using

the FP-1300 software and need to configure a different base arbitration ID, use the DIP switches

on the FP-1300 module. For more information about using DIP switches to configure the

arbitration ID, refer to the

FP-1300 User Manual.

CCoo

oonn

nnnn

nnee

eecc

cctttt tttthh

hhee

ee FF

FFPP

PP--

--11

1133

3300

0000

00 ttttoo

oo tttthh

hhee

ee CC

CCAA

AANN

NN NN

NNee

eettttww

wwoo

oorr

rrkk

CCAA

AAUU

UUTT

TTIIIIOO

OONN

NN Before you connect the FP-1300 to a CAN network, make sure the baud

rates of the FP-1300 and the CAN network are the same. The default baud rate of the

FP-1300 is 500 Kbps. If you are configuring the FP-1300 for the first time and the CAN

network is operating at a baud rate other than 500 Kbps, configure the FP-1300 to

operate at the appropriate baud rate before you install it on the CAN network. If you do

not, CAN network errors can occur, and other CAN devices on the network can go into

an error state. For more information, refer to the

Configuring the Baud Rate

section of

the

FP-1300 Configuration Utility Help.

7FP-1300 Quick Start Guide

National Instruments Corporation

Connecting the CAN Cable to the FP-1300

To connect an FP-1300 bank to the CAN network, complete the following steps.

A. Plug the Combicon-style connector into the CAN port.

B. Connect a shielded twisted-pair cable to the C_H and C_L terminals. Connect the shield of

this cable to the SH terminal. Refer to ISO 11898-2 for the maximum cable length between

the FP-1300 and the CAN network. C_H and C_L carry the data on the CAN network. For

noise immunity, solidly ground the shield of the cable as closely as possible to the FP-1300.

C. Connect a 10–30 VDC power supply to the V+ and V– terminals. V+ and V– supply power to

the CAN transceivers on the FP-1300.

D. Connect the other end of the CAN cable to a connector on the CAN network.

FP-1300 Quick Start Guide ni.com

Terminating the CAN Network

If you connect the FP-1300 to a multiple-device CAN network that is already terminated, go to

the

Wire Power to the FieldPoint System

section next. If you connect the FP-1300 to a single-

device CAN network, you need to terminate the network. To terminate the CAN network, follow

these steps:

A. Install a 120 Ωresistor between the C_H and C_L terminals on the FP-1300. The typical

resistance is 120 Ω. The maximum resistance is 130 Ω. The minimum allowable resistance

is 100 Ω.

B. Install another 120 Ωresistor at the other end of the CAN cable between the C_H and C_L

terminals.

When you terminate the CAN network, the effective resistance between C_H and C_L is 60 Ω.

NNOO

OOTT

TTEE

EE The Combicon-style connector and the CAN cable must have a nominal

impedance of 120 Ω. For more information, refer to ISO 11898-2.

9FP-1300 Quick Start Guide

National Instruments Corporation

WWiiiirr

rree

ee PP

PPoo

ooww

wwee

eerr

rr ttttoo

oo tttthh

hhee

ee FF

FFiiiiee

eelllldd

ddPP

PPoo

ooiiiinn

nntttt SS

SSyy

yyss

ssttttee

eemm

A. Connect 11–30 VDC power supply leads to either set of the V and C terminals on the

network module. If you want to verify that the power supply is sufficient for the modules

and devices, refer to the FieldPoint hardware documents for instructions on calculating

power requirements.

B. Connect power to the FieldPoint modules that require external power for outputs (output

modules, counter modules, PWM, PG, QUAD). Refer to the I/O module operating instructions

for power consumption details. You can power a module by connecting the V and C inputs on

its terminal base to a separate power supply, connecting the V and C outputs of a

neighboring terminal base or network module, or using a combination of both methods.

CCAA

AAUU

UUTT

TTIIIIOO

OONN

NN Cascading power defeats isolation between the cascaded modules.

FP-1300 Quick Start Guide ni.com

FP-1300 FP-AI-110 FP-AO-200 FP-RLY-420 FP-TC-120

15 16 V

31 32 C

V132

C17 18

Shades of gray indicate different

voltage potentials.

Separate Power Supply

(Recommended)

Cascaded Power

(Eliminates Isolation)

No External

Power Required

CCAA

AAUU

UUTT

TTIIIIOO

OONN

NN Cascading power from neighboring bases or network modules defeats

isolation between cascaded modules.

CCAA

AAUU

UUTT

TTIIIIOO

OONN

NN Cascading

power defeats isolation.

Andere Handbücher für FieldPoint FP-1300

Inhaltsverzeichnis

Andere National Instruments E/A-System Handbücher

National Instruments

National Instruments Quadrature Input Module FP-QUAD-510 Bedienungsanleitung

National Instruments

National Instruments PXIe-7867R Bedienungsanleitung

National Instruments

National Instruments 9219 Bedienungsanleitung

National Instruments

National Instruments FieldPoint FP-AI-112 Bedienungsanleitung

National Instruments

National Instruments 6527 Bedienungs- und Wartungshandbuch

National Instruments

National Instruments NI PCI-6510 Bedienungsanleitung

National Instruments

National Instruments 9225E Bedienungsanleitung

National Instruments

National Instruments NI 9437 Bedienungsanleitung

National Instruments

National Instruments 9220 Handbuch

National Instruments

National Instruments NI-5761 Bedienungsanleitung

National Instruments

National Instruments NI 9264 Bedienungsanleitung

National Instruments

National Instruments R Series Bedienungsanleitung

National Instruments

National Instruments NI 9236 Bedienungsanleitung

National Instruments

National Instruments BNC-2090A Bedienungsanleitung

National Instruments

National Instruments NI 9211E Bedienungsanleitung

National Instruments

National Instruments SC Express Series Bedienungsanleitung

National Instruments

National Instruments NI PXI-7851 Bedienungsanleitung

National Instruments

National Instruments PXIe-4357 Bedienungsanleitung

National Instruments

National Instruments FieldPoint cFP-1808 Bedienungsanleitung

National Instruments

National Instruments REM-11120 Bedienungsanleitung

National Instruments

National Instruments NI-9232 Bedienungsanleitung

National Instruments

National Instruments 9232 Handbuch

National Instruments

National Instruments USB-9213 Bedienungsanleitung

National Instruments

National Instruments 9401 Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung