National Instruments NI 9264 Bedienungsanleitung

NI-9264

GETTING STARTED GUIDE

NI 9264

16 AO, ±10 V, 16 Bit, 25 kS/s/ch Simultaneous

This document explains how to connect to the NI 9264. In this

document, the NI 9264 with spring terminal and the NI 9264 with

DSUB are referred to inclusively as the NI 9264.

Note Before you begin, complete the software and

hardware installation procedures in your chassis

documentation.

Note The guidelines in this document are specific to

the NI 9264. The other components in the system might

not meet the same safety ratings. Refer to the

documentation for each component in the system to

determine the safety and EMC ratings for the entire

system.

Caution Electrostatic Discharge (ESD) can damage

the NI 9264 with spring terminal. To prevent damage,

use industry-standard ESD prevention measures during

installation, maintenance, and operation.

Safety Guidelines

Operate the NI 9264 only as described in this document.

2| ni.com | NI 9264 Getting Started Guide

Caution Do not operate the NI 9264 in a manner not

specified in this document. Product misuse can result in

a hazard. You can compromise the safety protection

built into the product if the product is damaged in any

way. If the product is damaged, return it to NI for

repair.

Hazardous Voltage This icon denotes a warning

advising you to take precautions to avoid electrical

shock.

Safety Guidelines for Hazardous Voltages

You can connect hazardous voltages only to the

NI 9264 with spring terminal. Do not connect hazardous voltages

to the NI 9264 with DSUB.

If hazardous voltages are connected to the device, take the

following precautions. A hazardous voltage is a voltage greater

than 42.4 Vpk voltage or 60 VDC to earth ground.

Caution Ensure that hazardous voltage wiring is

performed only by qualified personnel adhering to local

electrical standards.

NI 9264 Getting Started Guide | © National Instruments | 3

Caution Do not mix hazardous voltage circuits and

human-accessible circuits on the same module.

Caution Ensure that devices and circuits connected to

the module are properly insulated from human contact.

Note When module terminals are hazardous voltage

LIVE (>42.4 Vpk/60 VDC), you must ensure that

devices and circuits connected to the module are

properly insulated from human contact. You must use

the NI 9940 connector backshell kit with the

NI 9264 with spring terminal to ensure that the

terminals are not accessible.

Safety Voltages

Connect only voltages that are within the following limits:

NI 9264 with Spring Terminal Isolation Voltages

Channel-to-channel None

4| ni.com | NI 9264 Getting Started Guide

Channel-to-earth ground

Continuous 250 Vrms,

Measurement Category II

Withstand up to

4,000 m

3,000 Vrms, verified by a 5 s

dielectric withstand test

Measurement Category II is for measurements performed on

circuits directly connected to the electrical distribution system.

This category refers to local-level electrical distribution, such as

that provided by a standard wall outlet, for example, 115 V for

U.S. or 230 V for Europe.

Caution Do not connect the

NI 9264 with spring terminal to signals or use for

measurements within Measurement Categories III or

IV.

NI 9264 with DSUB Isolation Voltages

Isolation

Channel-to-channel None

NI 9264 Getting Started Guide | © National Instruments | 5

Channel-to-earth ground

Continuous 60 VDC, Measurement

Category I

Withstand up to

2,000 m

1,000 Vrms, verified by a 5 s

dielectric withstand test

Measurement Category I is for measurements performed on

circuits not directly connected to the electrical distribution system

referred to as MAINS voltage. MAINS is a hazardous live

electrical supply system that powers equipment. This category is

for measurements of voltages from specially protected secondary

circuits. Such voltage measurements include signal levels, special

equipment, limited-energy parts of equipment, circuits powered

by regulated low-voltage sources, and electronics.

Caution Do not connect the NI 9264 with DSUB to

signals or use for measurements within Measurement

Categories II, III, or IV.

Note Measurement Categories CAT I and CAT O are

equivalent. These test and measurement circuits are not

intended for direct connection to the MAINS building

6| ni.com | NI 9264 Getting Started Guide

installations of Measurement Categories CAT II,

CAT III, or CAT IV.

Safety Guidelines for Hazardous Locations

The NI 9264 is suitable for use in Class I, Division 2, Groups A,

B, C, D, T4 hazardous locations; Class I, Zone 2, AEx nA IIC T4

and Ex nA IIC T4 hazardous locations; and nonhazardous

locations only. Follow these guidelines if you are installing the

NI 9264 in a potentially explosive environment. Not following

these guidelines may result in serious injury or death.

Caution Do not disconnect I/O-side wires or

connectors unless power has been switched off or the

area is known to be nonhazardous.

Caution Do not remove modules unless power has

been switched off or the area is known to be

nonhazardous.

Caution Substitution of components may impair

suitability for Class I, Division 2.

Caution For Division 2 and Zone 2 applications,

install the system in an enclosure rated to at least IP54

as defined by IEC/EN 60079-15.

NI 9264 Getting Started Guide | © National Instruments | 7

Caution For Division 2 and Zone 2 applications,

connected signals must be within the following limits.

Capacitance 0.2 µF maximum

Special Conditions for Hazardous Locations Use in

Europe and Internationally

The NI 9264 has been evaluated as Ex nA IIC T4 Gc equipment

under DEMKO 07 ATEX 0626664X and is IECEx UL 14.0089X

certified. Each NI 9264 is marked II 3G and is suitable for use

in Zone 2 hazardous locations, in ambient temperatures of -40 °C

≤ Ta ≤ 70 °C. If you are using the NI 9264 in Gas Group IIC

hazardous locations, you must use the device in an NI chassis that

has been evaluated as Ex nC IIC T4, Ex IIC T4, Ex nA IIC T4, or

Ex nL IIC T4 equipment.

Caution You must make sure that transient

disturbances do not exceed 140% of the rated voltage.

Caution The system shall only be used in an area of

not more than Pollution Degree 2, as defined in

IEC/EN 60664-1.

8| ni.com | NI 9264 Getting Started Guide

Caution The system shall be mounted in an

ATEX/IECEx-certified enclosure with a minimum

ingress protection rating of at least IP54 as defined in

IEC/EN 60079-15.

Caution The enclosure must have a door or cover

accessible only by the use of a tool.

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory

requirements and limits for electromagnetic compatibility (EMC)

stated in the product specifications. These requirements and

limits provide reasonable protection against harmful interference

when the product is operated in the intended operational

electromagnetic environment.

This product is intended for use in industrial locations. However,

harmful interference may occur in some installations, when the

product is connected to a peripheral device or test object, or if the

product is used in residential or commercial areas. To minimize

interference with radio and television reception and prevent

unacceptable performance degradation, install and use this

NI 9264 Getting Started Guide | © National Instruments | 9

Andere Handbücher für NI 9264

Inhaltsverzeichnis

Andere National Instruments E/A-System Handbücher

National Instruments

National Instruments NI-9230 Bedienungsanleitung

National Instruments

National Instruments PCI-6154 Kurzanleitung

National Instruments

National Instruments SCC-68 Bedienungsanleitung

National Instruments

National Instruments FieldPoint FP-AI-112 Bedienungsanleitung

National Instruments

National Instruments NI 653 Series Bedienungsanleitung

National Instruments

National Instruments USB-9211A Bedienungsanleitung

National Instruments

National Instruments 9753 Bedienungsanleitung

National Instruments

National Instruments DAQPad-1200 Bedienungsanleitung

National Instruments

National Instruments Data Acquisition Device E Series Bedienungsanleitung

National Instruments

National Instruments BNC-2090A Bedienungsanleitung

National Instruments

National Instruments PXIe-4322 Handbuch

National Instruments

National Instruments PXI-7854 Bedienungsanleitung

National Instruments

National Instruments PXIe-7846R Bedienungsanleitung

National Instruments

National Instruments Isolated Analog Input Modules SCC-AI01 Bedienungsanleitung

National Instruments

National Instruments NI 6238 Bedienungsanleitung

National Instruments

National Instruments PCI-6251 Bedienungsanleitung

National Instruments

National Instruments NI PXI-7851 Bedienungsanleitung

National Instruments

National Instruments NI 9231 Handbuch

National Instruments

National Instruments SCXI-1121 Handbuch

National Instruments

National Instruments NI-9207 Bedienungsanleitung

National Instruments

National Instruments USB-6221 OEM Bedienungsanleitung

National Instruments

National Instruments NI USB-7845R Bedienungsanleitung

National Instruments

National Instruments PCIe-7846 Bedienungsanleitung

National Instruments

National Instruments NI-9228 Handbuch

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung