NCR 7610-K452 Handbuch

Inhaltsverzeichnis

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung

7610-K452

Customer Display Base

Kit Instructions

Issue A

Revision Record

Issue

Date

Remarks

A

Feb 2011

First issue

1

Introduction

This kit provides a display base which attaches to the back of the Table Top Stand

(7610-K320). It supports the 5975 2x20 VFD Display Pole (5975-K834/K836) and the LCD

Customer Display Tilt Mount (7610-K453).

Components

2

Installing a 2x20 Display

1. Install the Customer Display Base on the back of the 7610 Table Top Stand

(7610-K320). Secure it with screws (2).

2. Connect the Display Cable to the Display Module.

Note: The RS-232 (or USB) cable can be connected to the Display Module

without disassembling the Display Assembly by extending the end of the cable

into the post opening and connecting it to the proper connector, or if you find this

difficult you can disassemble the Display Assembly as follows.

a. Remove the screws (2) from the Display Back.

b. Remove the Display Back.

c. Route the Interface Cable though the opening in the Display Back.

d. Connect the cable to the proper connector on the Display Module.

e. Reassemble the Display Assembly.

3

3. Route the cable through the Customer Display Pole.

4. Assemble the components as shown below. Note that the raised extension of the

Display Swivel is oriented toward the front of the unit, which permits the Display

to be tilted to the rear.

5. Insert the Display Pole into the Customer Display Base.

6. Connect the Display Cable to the terminal.

Note: The Display Cable should be routed up through the Table Top Stand to the

host terminal.

4

RS-232 Interface (Powered)

Connect the I/F cable to a powered RS-232 connector on the terminal.

Note: The factory default settings for the COM1 and COM2 ports are powered by

default. To change a port to non-powered see the Circuit Boards chapter in the

Hardware Service Guide.

Configure the terminal serial port as follows:

9600 baud, 8 data bits, 1 start bit, 1 stop bit, No parity

USB Interface (Powered)

Connect the I/F cable to a powered 12V Powered USB connector on the terminal.

Installing an LCD Display

For installation procedures for mounting an LCD display see the LCD Customer Display

Tilt Mount Kit Instructions (7610-K453).