NEC Express5800/120Rg-2 Bedienungsanleitung
System Release Notes
Express5800/120Rg-2
System Release Notes
PN: 455-01716-000
Proprietary Notice and Liability Disclaimer
The information disclosed in this document, including all designs and related materials, is
the valuable property of NEC Solutions (America), Inc. and/or its licensors. NEC Solutions
(America), Inc. and/or its licensors, as appropriate, reserve all patent, copyright and other
proprietary rights to this document, including all design, manufacturing, reproduction, use,
and sales rights thereto, except to the extent said rights are expressly granted to others.
The NEC Solutions (America), Inc. product(s) discussed in this document are warranted in
accordance with the terms of the Warranty Statement accompanying each product.
However, actual performance of each product is dependent upon factors such as system
configuration, customer data, and operator control. Since implementation by customers of
each product may vary, the suitability of specific product configurations and applications
must be determined by the customer and is not warranted by NEC Solutions (America), Inc.
To allow for design and specification improvements, the information in this document is
subject to change at any time, without notice. Reproduction of this document or portions
thereof without prior written approval of NEC Solutions (America), Inc. is prohibited.
Trademarks
Windows 2003 and Windows NT are registered trademarks of Microsoft Corporation.
SCO OpenServer is a trademark of Caldera Systems, Inc.
All other product, brand, or trade names used in this publication are the trademarks or registered trademarks
of their respective trademark owners.
September 2004
Copyright 2004
NEC Solutions (America), Inc
10850 Gold Center Drive, Suite 200,
Rancho Cordova, CA 95670
All Rights Reserved
Express5800/120Rg-2
System Release Notes
The Express5800/120Rg-2 System Release Notes provide up-to-date information
on your system. These notes also provide additional valuable information about
your system that was not included in the user’s guide.
Please read these notes in their entirety.
CONTENTS
Introduction ............................................................................................................................................3
General Comments.................................................................................................................................3
Advisories...............................................................................................................................................3
EXPRESSBUILDER.........................................................................................................................3
Notices and Restrictions.........................................................................................................................4
nec
Introduction
These System Release Notes cover the following topics:
General Comments
Advisories
Notices and Restrictions
General Comments
The following general comments apply to this server.
Versions of the Network Operating Systems tested and recommended are:
⎯Windows®2003
Microsoft Windows® 2000 and NT© 4.0 are not supported.
SCO OpenServer™5.06 is not supported.
Advisories
EXPRESSBUILDER
The following advisories apply to EXPRESSBUILDER.
Windows 2003 must be installed using EXPRESSBUILDER Express Setup
to take full advantage of NEC specific software for your server.
Note: This advisory does not apply if your operating
system was preloaded at the factory.
If you already have an operating system installed when creating a
maintenance partition, EXPRESSBUILDER will warn you of the existing
partition. If you want to preserve the installed operating system, do not
create the maintenance partition or the existing operating system will be
overlaid by the maintenance partition.
The Administrator Menu in the System Information Management segment
of the Offline Maintenance Utility is accessible only by NEC authorized
service representatives.
EXPRESSBUILDER operates in floppy emulation mode. The emulated
floppy drive portion of your system CD-ROM is designated Drive A and the
remaining portion(s) of the CD-ROM is designated Drive Q. Your system
diskette drive is Drive B. After creating the Off-line Maintenance Utility
diskette, EXPRESSBUILDER prompts you to remove the diskette from
Drive B. At this prompt, remove the diskette from your diskette drive.
Express5800/120Rg-2 System Release Notes 3
Notices and Restrictions
Express5800/120Rg-2
Notices and Restrictions
This document describes the restrictions on Express5800/120Rg-2. Please read the list of notices
below carefully to ensure that they are followed.
List of Notices
Notices Models
1 Note when using Remote Management Card (N8115-01, N8115-02)
When using modem for Express Report Service, use serial port A.
<supplement>
When using serial port B (for example UPS), do the setting as below;
In EXPRESSBUILDER menu, ”System Management Function” ->”System
Management Setting” ->”Configuration” ->”Change”->”Common”
Set “Alert” and “Remote Control (WAN/Direct)” as “Disable”.
(Default setting is “Disable”.)
2 Note for Seamless set up with SCSI HostRAID (On-Board RAID)
Configuration
Installation procedure is as follows
(1) When SCSI back up device is connected, take off cable connection.
(2) Start “SCSI Select™ Utility” menu in POST, set the HostRAID function on
both of SCSI A/B as “Enable”, and do the installation.
* Refer to the User’s Guide for how to set the HostRAID function.
(3) After finishing installation, connect back up device with cable.
(4) Start “SCSI Select™ Utility” menu in POST, set the HostRAID function on the
channel which is connected to the SCSI back up device as “disable”.
* Refer to the User’s Guide for HostRAID setting.
3 Note when using HostRAID configuration on Windows 2000 Advanced Server
+ SP4 (if procured, installed, and supported by customer)
Memory capacity should be 6GB or less. (6GB is supported.)
120Rg-2
4 Note when using LAN for Management
When using LAN for Management, for example Wake On LAN or the alert
function via LAN using Remote Management Card, use LAN#1 port. LAN#2
port should not be used as LAN for management.
120Rg-2
If you have any questions about this document, please contact your sales representative.
4Express5800/120Rg-2 System Release Notes
Andere Handbücher für Express5800/120Rg-2
2
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere NEC Server Handbücher
NEC
NEC Express5800/320Ma Bedienungsanleitung
NEC
NEC Express5800/R310e-E4 Bedienungsanleitung
NEC
NEC N8100-1422F Bedienungsanleitung
NEC
NEC Express5800/T110g-S Bedienungsanleitung
NEC
NEC Express 5800 Bedienungsanleitung
NEC
NEC Express5800/T110g-S Bedienungsanleitung
NEC
NEC Univerge SV9100 Bedienungsanleitung
NEC
NEC Express5800/320Ma Bedienungsanleitung
NEC
NEC Express 5800 Bedienungsanleitung
NEC
NEC NE3108-007 Bedienungsanleitung
NEC
NEC NEC Express5800 Series Bedienungsanleitung
NEC
NEC NEC Express5800 Series Bedienungsanleitung
NEC
NEC Express 5800 TM700 Bedienungsanleitung
NEC
NEC N8400-230F Bedienungsanleitung
NEC
NEC LC1400 Bedienungsanleitung
NEC
NEC ES1200 Bedienungsanleitung
NEC
NEC SX-Aurora TSUBASA A300-4 Bedienungsanleitung
NEC
NEC NEC Express5800 Series Bedienungsanleitung
NEC
NEC Express5800/320Fd-LR Bedienungsanleitung
NEC
NEC INTEL 5800/1000 Bedienungsanleitung
Beliebte Server Handbücher anderer Marken
Nortel
Nortel 1000 Con?guration guide Bedienungsanleitung
Asus
Asus AP7500 Bedienungs- und Wartungshandbuch
Avid Technology
Avid Technology AirSpeed 5000 Bedienungsanleitung
HP
HP Integrity rx2600 Installationsanleitung
Milestone
Milestone Husky IVO 350T Bedienungsanleitung
Planet
Planet NAS-7410 Bedienungsanleitung