NETGEAR ReadyNAS NV+ Bedienungsanleitung

Installation Guide

)NSTALLATION'UIDE

NETGEAR ReadyNAS NV+

Start Here

Follow these instructions to install your NETGEAR® ReadyNAS™ NV+. Then, consult

the ReadyNAS Setup Manual on your Installation CD for instructions on installing the

RAIDar utility and using the FrontView Setup Wizard to configure ReadyNAS. Access

the ReadyNAS User Guide on the Installation CD to configure any advanced features. The

ReadyNAS User Guide is also on the NETGEAR support site at

http://kbserver.netgear.com.

Warning: If you purchased a diskless unit, please read the optional disk installation

section before installing the RAIDar™ utility or connecting ReadyNAS to the network.

First, check your package contents

Before starting installation, check your package contents:

• ReadyNAS NV+

• Four hard disk trays

• Installation Guide

• Warranty Card

• Power cable

• Ethernet cable

• ReadyNAS Installation CD

• 16 screws for hard disk installation (included only with diskless units)

Then, take a moment to identify the features of your

ReadyNAS NV+

A. USB port (1)

B. Programmable backup button

C. Disk LEDs. Green for disk online.

D. Activity LED. Blinks for disk access.

E. Power button with indication LED

F. Disk tray door.

G. LCD display panel

H. Disk tray door access

I. Unit handle

J. System reset switch pin

K. USB port (2) and (3)

L. Ethernet port (RJ45)

M. Cooling fan

N. Power connector (100-

240VAC, 50/60HZ)

O. Label (includes serial

number and MAC address)

P. Kensington security lock

Install the hard disks (optional)

This is an optional step, required only if you purchased a diskless unit.

1. Remove the disk tray from the unit:

a. Open the door.

b. Press to release the latch.

c. Pull out the tray.

2. Insert a hard drive into the tray. Position

the drive with the bottom facing out from

the tray, and the connectors facing away.

Use the four screws provided with the

unit to secure the drive to the tray.

3. With the latch in the open position (1), slide the disk tray into the unit completely,

securing the latch and closing the door (2).

Note: If you want to prevent easy removal of the disk from the drive bay, set the lock

(3): to the right is unlocked; to the left is locked.

Finally, install the RAIDar utility

Your Installation CD contains the RAIDar utility for Windows, MAC and Linux. See the

ReadyNAS Setup Manual for installation instructions. When you complete installation of

the RAIDar utility, you are ready to power on ReadyNAS.

Initialize hard disks (if disks installed separately)

If you purchased a diskless ReadyNAS, after you install the hard disks and perform the

RAID Configuration, you must wait until the volume creation has completed before

accessing the FrontView™ Setup Wizard (see theReadyNAS Setup Manual and ReadyNAS

User Guide for complete instructions). It will take up to 2 hours, depending on disk

capacity.

An additional 2 to 10 hours are required before the RAID synchronization has completed

and the system is fully redundant. During the background RAID synchronization, access

to the NAS will be slower than normal. The RAIDar column, shown in the following

table, will indicate progress.

Installation Guide

)NSTALLATION'UIDE

NETGEAR ReadyNAS NV+

Start Here

Follow these instructions to install your NETGEAR® ReadyNAS™ NV+. Then, consult

the ReadyNAS Setup Manual on your Installation CD for instructions on installing the

RAIDar utility and using the FrontView Setup Wizard to configure ReadyNAS. Access

the ReadyNAS User Guide on the Installation CD to configure any advanced features. The

ReadyNAS User Guide is also on the NETGEAR support site at

http://kbserver.netgear.com.

Warning: If you purchased a diskless unit, please read the optional disk installation

section before installing the RAIDar™ utility or connecting ReadyNAS to the network.

First, check your package contents

Before starting installation, check your package contents:

• ReadyNAS NV+

• Four hard disk trays

• Installation Guide

• Warranty Card

• Power cable

• Ethernet cable

• ReadyNAS Installation CD

• 16 screws for hard disk installation (included only with diskless units)

Then, take a moment to identify the features of your

ReadyNAS NV+

A. USB port (1)

B. Programmable backup button

C. Disk LEDs. Green for disk online.

D. Activity LED. Blinks for disk access.

E. Power button with indication LED

F. Disk tray door.

G. LCD display panel

H. Disk tray door access

I. Unit handle

J. System reset switch pin

K. USB port (2) and (3)

L. Ethernet port (RJ45)

M. Cooling fan

N. Power connector (100-

240VAC, 50/60HZ)

O. Label (includes serial

number and MAC address)

P. Kensington security lock

Install the hard disks (optional)

This is an optional step, required only if you purchased a diskless unit.

1. Remove the disk tray from the unit:

a. Open the door.

b. Press to release the latch.

c. Pull out the tray.

2. Insert a hard drive into the tray. Position

the drive with the bottom facing out from

the tray, and the connectors facing away.

Use the four screws provided with the

unit to secure the drive to the tray.

3. With the latch in the open position (1), slide the disk tray into the unit completely,

securing the latch and closing the door (2).

Note: If you want to prevent easy removal of the disk from the drive bay, set the lock

(3): to the right is unlocked; to the left is locked.

Finally, install the RAIDar utility

Your Installation CD contains the RAIDar utility for Windows, MAC and Linux. See the

ReadyNAS Setup Manual for installation instructions. When you complete installation of

the RAIDar utility, you are ready to power on ReadyNAS.

Initialize hard disks (if disks installed separately)

If you purchased a diskless ReadyNAS, after you install the hard disks and perform the

RAID Configuration, you must wait until the volume creation has completed before

accessing the FrontView™ Setup Wizard (see theReadyNAS Setup Manual and ReadyNAS

User Guide for complete instructions). It will take up to 2 hours, depending on disk

capacity.

An additional 2 to 10 hours are required before the RAID synchronization has completed

and the system is fully redundant. During the background RAID synchronization, access

to the NAS will be slower than normal. The RAIDar column, shown in the following

table, will indicate progress.

Installation Guide

)NSTALLATION'UIDE

NETGEAR ReadyNAS NV+

Start Here

Follow these instructions to install your NETGEAR® ReadyNAS™ NV+. Then, consult

the ReadyNAS Setup Manual on your Installation CD for instructions on installing the

RAIDar utility and using the FrontView Setup Wizard to configure ReadyNAS. Access

the ReadyNAS User Guide on the Installation CD to configure any advanced features. The

ReadyNAS User Guide is also on the NETGEAR support site at

http://kbserver.netgear.com.

Warning: If you purchased a diskless unit, please read the optional disk installation

section before installing the RAIDar™ utility or connecting ReadyNAS to the network.

First, check your package contents

Before starting installation, check your package contents:

• ReadyNAS NV+

• Four hard disk trays

• Installation Guide

• Warranty Card

• Power cable

• Ethernet cable

• ReadyNAS Installation CD

• 16 screws for hard disk installation (included only with diskless units)

Then, take a moment to identify the features of your

ReadyNAS NV+

A. USB port (1)

B. Programmable backup button

C. Disk LEDs. Green for disk online.

D. Activity LED. Blinks for disk access.

E. Power button with indication LED

F. Disk tray door.

G. LCD display panel

H. Disk tray door access

I. Unit handle

J. System reset switch pin

K. USB port (2) and (3)

L. Ethernet port (RJ45)

M. Cooling fan

N. Power connector (100-

240VAC, 50/60HZ)

O. Label (includes serial

number and MAC address)

P. Kensington security lock

Install the hard disks (optional)

This is an optional step, required only if you purchased a diskless unit.

1. Remove the disk tray from the unit:

a. Open the door.

b. Press to release the latch.

c. Pull out the tray.

2. Insert a hard drive into the tray. Position

the drive with the bottom facing out from

the tray, and the connectors facing away.

Use the four screws provided with the

unit to secure the drive to the tray.

3. With the latch in the open position (1), slide the disk tray into the unit completely,

securing the latch and closing the door (2).

Note: If you want to prevent easy removal of the disk from the drive bay, set the lock

(3): to the right is unlocked; to the left is locked.

Finally, install the RAIDar utility

Your Installation CD contains the RAIDar utility for Windows, MAC and Linux. See the

ReadyNAS Setup Manual for installation instructions. When you complete installation of

the RAIDar utility, you are ready to power on ReadyNAS.

Initialize hard disks (if disks installed separately)

If you purchased a diskless ReadyNAS, after you install the hard disks and perform the

RAID Configuration, you must wait until the volume creation has completed before

accessing the FrontView™ Setup Wizard (see theReadyNAS Setup Manual and ReadyNAS

User Guide for complete instructions). It will take up to 2 hours, depending on disk

capacity.

An additional 2 to 10 hours are required before the RAID synchronization has completed

and the system is fully redundant. During the background RAID synchronization, access

to the NAS will be slower than normal. The RAIDar column, shown in the following

table, will indicate progress.

This symbol was placed in accordance with the European Union Directive 2002/96 on the

Waste Electrical and Electronic Equipment (the WEEE Directive). If disposed of within

the European Union, this product should be treated and recycled in accordance with the

laws of your jurisdiction implementing the WEEE Directive.

registered trademarks of NETGEAR, Inc. in the United States and/or other countries. Other brand and

product names are trademarks or registered trademarks of their respective holders. Information is

subject to change without notice.

March 2009

.Duration Act Description LED Description RAIDar Information

2 minutes Initial boot up OS booting

10 minutes Perform RAID configuration on RAIDar (optional) Waiting for RAIDar config Click Setup

~ 2 hours Volume Creation Installing

Creating Volume/booting Installing

Creating/booting

ReadyNAS is not accessible during this time

~ 10 hours RAID synchronization. ReadyNAS is accessible during this time. IP Address; Host Name Firmware Version

Normal status. ReadyNAS is fully redundant. IP Address; Host Name Firmware Version

ErroraNo disks detected if all disk LEDs flash at once, and if disk 2 flashes

repeatedly Error. No disk detected. Firmware version

ErroraBad disk detected if one disk LED flashes once per second.

The disk corresponding to this LED is bad. IP Address; Host Name Firmware Version

a. Installation will abort if an error is detected.

Legend: LED off; LED on; LED slow blinking; LED fast blinking

When connecting ReadyNAS, please note the following:

•ReadyNAS connected directly to your network: If your client has a static IP

address, make sure it is on the same IP address subnet as the ReadyNAS device. You

can do this by configuring your client to obtain its IP address via DHCP. Even if your

network does not have existing DHCP service, the ReadyNAS device will assure that

you will get an IP address.

•ReadyNAS connected directly to your PC: If you are connecting a PC directly to

ReadyNAS (and not through a network), first set a static IP address on your PC in the

192.168.168.xxx subnet, subnet mask 255.255.255.0. You can then use RAIDar to

detect ReadyNAS, or you can open a browser and enter the ReadyNAS default IP

address https://192.168.168.168/admin to connect to the ReadyNAS.

Technical Support

Thank you for selecting NETGEAR products. After installing your device, locate the

serial number on the label of your product and use it to register your product at http://

www.NETGEAR.com/register. Registration is required before you can use our telephone

support service. Registration via our website is strongly recommended.

Go to http://kbserver.netgear.com for product updates and Web support. For Warranty and

Regional Customer Support information, see the Resource CD that came with your

product.

An approved hard disk hardware list is available from the NETGEAR Support site.

Connect ReadyNAS

ReadyNAS connected directly to your network.

ReadyNAS connected directly to your PC (no cross-over

cable needed).

This symbol was placed in accordance with the European Union Directive 2002/96 on the

Waste Electrical and Electronic Equipment (the WEEE Directive). If disposed of within

the European Union, this product should be treated and recycled in accordance with the

laws of your jurisdiction implementing the WEEE Directive.

registered trademarks of NETGEAR, Inc. in the United States and/or other countries. Other brand and

product names are trademarks or registered trademarks of their respective holders. Information is

subject to change without notice.

March 2009

.Duration Act Description LED Description RAIDar Information

2 minutes Initial boot up OS booting

10 minutes Perform RAID configuration on RAIDar (optional) Waiting for RAIDar config Click Setup

~ 2 hours Volume Creation Installing

Creating Volume/booting Installing

Creating/booting

ReadyNAS is not accessible during this time

~ 10 hours RAID synchronization. ReadyNAS is accessible during this time. IP Address; Host Name Firmware Version

Normal status. ReadyNAS is fully redundant. IP Address; Host Name Firmware Version

ErroraNo disks detected if all disk LEDs flash at once, and if disk 2 flashes

repeatedly Error. No disk detected. Firmware version

ErroraBad disk detected if one disk LED flashes once per second.

The disk corresponding to this LED is bad. IP Address; Host Name Firmware Version

a. Installation will abort if an error is detected.

Legend: LED off; LED on; LED slow blinking; LED fast blinking

When connecting ReadyNAS, please note the following:

•ReadyNAS connected directly to your network: If your client has a static IP

address, make sure it is on the same IP address subnet as the ReadyNAS device. You

can do this by configuring your client to obtain its IP address via DHCP. Even if your

network does not have existing DHCP service, the ReadyNAS device will assure that

you will get an IP address.

•ReadyNAS connected directly to your PC: If you are connecting a PC directly to

ReadyNAS (and not through a network), first set a static IP address on your PC in the

192.168.168.xxx subnet, subnet mask 255.255.255.0. You can then use RAIDar to

detect ReadyNAS, or you can open a browser and enter the ReadyNAS default IP

address https://192.168.168.168/admin to connect to the ReadyNAS.

Technical Support

Thank you for selecting NETGEAR products. After installing your device, locate the

serial number on the label of your product and use it to register your product at http://

www.NETGEAR.com/register. Registration is required before you can use our telephone

support service. Registration via our website is strongly recommended.

Go to http://kbserver.netgear.com for product updates and Web support. For Warranty and

Regional Customer Support information, see the Resource CD that came with your

product.

An approved hard disk hardware list is available from the NETGEAR Support site.

Connect ReadyNAS

ReadyNAS connected directly to your network.

ReadyNAS connected directly to your PC (no cross-over

cable needed).

This symbol was placed in accordance with the European Union Directive 2002/96 on the

Waste Electrical and Electronic Equipment (the WEEE Directive). If disposed of within

the European Union, this product should be treated and recycled in accordance with the

laws of your jurisdiction implementing the WEEE Directive.

registered trademarks of NETGEAR, Inc. in the United States and/or other countries. Other brand and

product names are trademarks or registered trademarks of their respective holders. Information is

subject to change without notice.

March 2009

.Duration Act Description LED Description RAIDar Information

2 minutes Initial boot up OS booting

10 minutes Perform RAID configuration on RAIDar (optional) Waiting for RAIDar config Click Setup

~ 2 hours Volume Creation Installing

Creating Volume/booting Installing

Creating/booting

ReadyNAS is not accessible during this time

~ 10 hours RAID synchronization. ReadyNAS is accessible during this time. IP Address; Host Name Firmware Version

Normal status. ReadyNAS is fully redundant. IP Address; Host Name Firmware Version

ErroraNo disks detected if all disk LEDs flash at once, and if disk 2 flashes

repeatedly Error. No disk detected. Firmware version

ErroraBad disk detected if one disk LED flashes once per second.

The disk corresponding to this LED is bad. IP Address; Host Name Firmware Version

a. Installation will abort if an error is detected.

Legend: LED off; LED on; LED slow blinking; LED fast blinking

When connecting ReadyNAS, please note the following:

•ReadyNAS connected directly to your network: If your client has a static IP

address, make sure it is on the same IP address subnet as the ReadyNAS device. You

can do this by configuring your client to obtain its IP address via DHCP. Even if your

network does not have existing DHCP service, the ReadyNAS device will assure that

you will get an IP address.

•ReadyNAS connected directly to your PC: If you are connecting a PC directly to

ReadyNAS (and not through a network), first set a static IP address on your PC in the

192.168.168.xxx subnet, subnet mask 255.255.255.0. You can then use RAIDar to

detect ReadyNAS, or you can open a browser and enter the ReadyNAS default IP

address https://192.168.168.168/admin to connect to the ReadyNAS.

Technical Support

Thank you for selecting NETGEAR products. After installing your device, locate the

serial number on the label of your product and use it to register your product at http://

www.NETGEAR.com/register. Registration is required before you can use our telephone

support service. Registration via our website is strongly recommended.

Go to http://kbserver.netgear.com for product updates and Web support. For Warranty and

Regional Customer Support information, see the Resource CD that came with your

product.

An approved hard disk hardware list is available from the NETGEAR Support site.

Connect ReadyNAS

ReadyNAS connected directly to your network.

ReadyNAS connected directly to your PC (no cross-over

cable needed).

This symbol was placed in accordance with the European Union Directive 2002/96 on the

Waste Electrical and Electronic Equipment (the WEEE Directive). If disposed of within

the European Union, this product should be treated and recycled in accordance with the

laws of your jurisdiction implementing the WEEE Directive.

registered trademarks of NETGEAR, Inc. in the United States and/or other countries. Other brand and

product names are trademarks or registered trademarks of their respective holders. Information is

subject to change without notice.

March 2009

.Duration Act Description LED Description RAIDar Information

2 minutes Initial boot up OS booting

10 minutes Perform RAID configuration on RAIDar (optional) Waiting for RAIDar config Click Setup

~ 2 hours Volume Creation Installing

Creating Volume/booting Installing

Creating/booting

ReadyNAS is not accessible during this time

~ 10 hours RAID synchronization. ReadyNAS is accessible during this time. IP Address; Host Name Firmware Version

Normal status. ReadyNAS is fully redundant. IP Address; Host Name Firmware Version

ErroraNo disks detected if all disk LEDs flash at once, and if disk 2 flashes

repeatedly Error. No disk detected. Firmware version

ErroraBad disk detected if one disk LED flashes once per second.

The disk corresponding to this LED is bad. IP Address; Host Name Firmware Version

a. Installation will abort if an error is detected.

Legend: LED off; LED on; LED slow blinking; LED fast blinking

When connecting ReadyNAS, please note the following:

•ReadyNAS connected directly to your network: If your client has a static IP

address, make sure it is on the same IP address subnet as the ReadyNAS device. You

can do this by configuring your client to obtain its IP address via DHCP. Even if your

network does not have existing DHCP service, the ReadyNAS device will assure that

you will get an IP address.

•ReadyNAS connected directly to your PC: If you are connecting a PC directly to

ReadyNAS (and not through a network), first set a static IP address on your PC in the

192.168.168.xxx subnet, subnet mask 255.255.255.0. You can then use RAIDar to

detect ReadyNAS, or you can open a browser and enter the ReadyNAS default IP

address https://192.168.168.168/admin to connect to the ReadyNAS.

Technical Support

Thank you for selecting NETGEAR products. After installing your device, locate the

serial number on the label of your product and use it to register your product at http://

www.NETGEAR.com/register. Registration is required before you can use our telephone

support service. Registration via our website is strongly recommended.

Go to http://kbserver.netgear.com for product updates and Web support. For Warranty and

Regional Customer Support information, see the Resource CD that came with your

product.

An approved hard disk hardware list is available from the NETGEAR Support site.

Connect ReadyNAS

ReadyNAS connected directly to your network.

ReadyNAS connected directly to your PC (no cross-over

cable needed).

Andere Handbücher für ReadyNAS NV+

Inhaltsverzeichnis

Andere NETGEAR Netzwerkspeicherserver Handbücher

NETGEAR

NETGEAR ReadyNAS 3220 Series Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS 4200 Bedienungsanleitung

NETGEAR

NETGEAR RNDP600E - ReadyNAS Pro Pioneer Edition NAS... Bedienungsanleitung

NETGEAR

NETGEAR RNR4410 - ReadyNAS 1100 NAS Server Montageanleitung

NETGEAR

NETGEAR ReadyNAS 102 Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS 1100 Handbuch

NETGEAR

NETGEAR READYNAS NV+ RND4425v1 Montageanleitung

NETGEAR

NETGEAR ReadyNAS RN312 Bedienungsanleitung

NETGEAR

NETGEAR RNDU4000-100NAS Montageanleitung

NETGEAR

NETGEAR RND2110 - ReadyNAS Duo NAS Server Benutzerhandbuch

NETGEAR

NETGEAR ReadyNAS RAIDiator 5.3 Bedienungsanleitung

NETGEAR

NETGEAR RNDU4000 Bedienungsanleitung

NETGEAR

NETGEAR RNDX400E - ReadyNAS NVX Pioneer Edition NAS... Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS RAIDiator 5.3 Bedienungsanleitung

NETGEAR

NETGEAR ReadyNASUltra 2 Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS Pro Pioneer Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS 102 Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS 2100 Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS Pro Business Bedienungsanleitung

NETGEAR

NETGEAR MS2110-100NAS Bedienungsanleitung

NETGEAR

NETGEAR RND4000 - ReadyNAS NV+ NAS Server Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS 3100 Handbuch

NETGEAR

NETGEAR ReadyNAS RN312 Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS 3200 Bedienungsanleitung

Beliebte Netzwerkspeicherserver Handbücher anderer Marken

HP NetStorage 6000 Bedienungsanleitung

Seagate

Seagate U10 ST320423A Bedienungsanleitung

Synology

Synology RackStation RS816 Handbuch

D-Link

D-Link ShareCenter Pro DNS-1200-05 Bedienungsanleitung

Avid Technology

Avid Technology VideoRAID ST Sicherheitsleitfaden

Western Digital

Western Digital My Cloud Home Duo Bedienungsanleitung

PrimeArray

PrimeArray 4xxx Bedienungsanleitung

Buffalo

Buffalo TeraStation WSS WSH5010N6 Bedienungsanleitung

Planex

Planex MZK-NAS01SG Bedienungsanleitung

Intel

Intel SS4000-E - Entry Storage System NAS Server Bedienungsanleitung

Synology

Synology RS2212+ Bedienungsanleitung

Allnet

Allnet ALL69000 Bedienungsanleitung

Adaptec

Adaptec 5325301580 Bedienungsanleitung

Motorola

Motorola EXORdisk II Bedienungsanleitung

Sony

Sony XDAAI1PK Bedienungsanleitung

Cisco

Cisco Linksys NAS200 Original Betriebsanleitung

Sans Digital

Sans Digital MR4UT6G Bedienungsanleitung

AIC

AIC FB128-LX Bedienungsanleitung