NETGEAR ProSafe Premium WNDAP620 Bedienungsanleitung

350 East Plumeria Drive

San Jose, CA 95134

USA

October 2012

202-10983-02

v2.0

ProSafe Premium 3 x 3

Dual-Band Wireless-N

Access Point WNDAP620

Reference Manual

ProSafe Premium 3 x 3 Dual-Band Wireless-N Access Point WNDAP620

Support

Thank you for choosing NETGEAR.

After installing your device, locate the serial number on the label of your product and use it to register your product

at https://my.netgear.com. You must register your product before you can use NETGEAR telephone support.

NETGEAR recommends registering your product through the NETGEAR website. For product updates and web

support, visit http://support.netgear.com.

Phone (US & Canada only): 1-888-NETGEAR.

Phone (Other Countries): Check the list of phone numbers at

http://support.netgear.com/general/contact/default.aspx.

NETGEAR recommends that you use only the official NETGEAR support resources.

Trademarks

NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of

NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to change

without notice. Other brand and product names are registered trademarks or trademarks of their respective

Revision History

Publication

Part Number Version Publish Date Comments

202-10983-02 2.0 October 2012 Minor nontechnical revisions

202-10983-02 1.0 September 2012 • Added and refined information (no new features added)

• Added Appendix B, Command-Line Reference

• Added Index

202-10983-01 1.0 August 2012 First publication

Contents

Chapter 1 Introduction

About the ProSafe Premium 3 x 3 Dual-Band Wireless-N Access Point

WNDAP620 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

What Is in the Box? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

System Requirements . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Key Features and Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Supported Standards and Conventions . . . . . . . . . . . . . . . . . . . . . . . . . .8

Key Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

802.11b/g/n and 802.11a/n Standards–Based Wireless Networking . . .11

Autosensing Ethernet Connections with Auto Uplink . . . . . . . . . . . . . . .11

Hardware Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Top Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Bottom Panel with Product Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Chapter 2 Installation and Basic Configuration

What You Need Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Wireless Equipment Placement and Range Guidelines. . . . . . . . . . . . .17

Ethernet Cabling Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

LAN Configuration Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Hardware Requirements for Computers on Your LAN. . . . . . . . . . . . . .19

Operating Frequency (Channel) Guidelines. . .. . . . . . . . . . . . . . . . . . .19

Requirements for Entering IP Addresses. . . . . . . . . . . . . . . . . . . . . . . .19

Install and Configure the Wireless Access Point . . . . . . . . . . . . . . . . . . . .20

Connect the Wireless Access Point to a Computer . . . . . . . . . . . . . . . .20

Configure Basic General System Settingsand Time Settings . . . . . . . .23

Configure the IPv4 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Configure the Optional DHCPv4 Server. . . . . . . . . . . . . . . . . . . . . . . . .27

Configure the Basic Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . .28

Test Basic Wireless Connectivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Mount the Wireless Access Point. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Ceiling Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Wall Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Desk Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

ProSafe Premium 3 x 3 Dual-Band Wireless-N Access Point WNDAP620

Chapter 3 Wireless Configuration and Security

Wireless Data Security Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Security Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Before You Change the SSID, WEP, and WPA Settings. . . . . . . . . . . .46

Configure and Enable Security Profiles . . . . . . . . . . . . . . . . . . . . . . . . .48

Configure RADIUS Server Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57

Restrict Wireless Access by MAC Address . . . . . . . . . . . . . . . . . . . . . . . .60

Schedule the Wireless Radio to Be Turned Off . . . . . . . . . . . . . . . . . . . . .61

Configure Basic Wireless Quality of Service . . . . . . . . . . . . . . . . . . . . . . .62

Chapter 4 Management and Monitoring

Enable Remote Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

SNMP Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

Secure Shell and Telnet Management. . . . . . . . . . . . . . . . . . . . . . . . . .66

Upgrade the Wireless Access Point Software . . . . . . . . . . . . . . . . . . . . . .67

Web Browser Upgrade Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

TFTP Server Upgrade Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

Manage the Configuration File or Reset to Factory Defaults . . . . . . . . . . .70

Save the Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70

Restore the Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71

Restore the Wireless Access Point to the Factory Default Settings. . . .71

Reboot the Wireless Access Point without Restoring the

Default Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73

Change the Administrator Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74

Manage User Accounts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

Enable the Syslog Server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76

Monitor the Wireless Access Point. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77

View System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77

Monitor Wireless Stations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

View the Activity Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83

Traffic Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83

Enable Rogue AP Detection and Monitor Access Points. . . . . . . . . . . . . .85

Enable and Configure Rogue AP Detection. . .. . . . . . . . . . . . . . . . . . .85

View and Save Access Point Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87

Configure Wireless Intrusion Detection and Prevention. . . . . . . . . . . . . . .89

Configure Wireless Intrusion Detection and Prevention Policy Settings 89

Configure Wireless Intrusion Detection and Prevention Mail Settings . .95

Monitor Traps, Counters, and Ad Hoc Networks . . . . . . . . . . . . . . . . . .96

Chapter 5 Advanced Configuration

Configure IPv6 Settings and Optional DHCPv6 Server Settings . . . . . . . .99

Configure the IPv6 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99

Configure the Optional DHCPv6 Server. . . . . . . . . . . . . . . . . . . . . . . .101

Configure Spanning Tree Protocol, 802.1Q VLAN, and

Link Layer Discovery Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103

Configure STP and VLANs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103

ProSafe Premium 3 x 3 Dual-Band Wireless-N Access Point WNDAP620

Configure Ethernet LLDP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105

Configure Hotspot Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106

Configure Advanced Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . .107

Configure Advanced Quality of Service Settings . . . . . . . . . . . . . . . . . . .110

Configure Quality of Service Policies . . . . . . . . . . . . . . . . . . . . . . . . . . . .112

Configure Wireless Bridging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118

Configure a Point-to-Point Wireless Network . . . . . . . . . . . . . . . . . . . .118

Configure a Point-to-Multipoint Wireless Network . . . . . . . . . . . . . . . .122

Configure the Wireless Access Point to Repeat the Wireless

Signal Using Point-to-Multipoint Bridge Mode . . . . . . . . . . . . . . . . . . .126

Chapter 6 Troubleshooting

Basic Functioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132

Verify the Correct Sequence of Events at Startup . . . . . . . . . . . . . . . .132

No LEDs Are Lit on the Wireless Access Point . . . . . . . . . . . . . . . . . .132

The Active LED or the LAN LED Is Not Lit . . . . . . . . . . . . . . . . . . . . . .133

The WLAN LED Does Not Light Up . . . . . . . . . . . . . . . . . . . . . . . . . . .133

You Cannot Access the Internet or the LAN from a

Wireless-Capable Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134

You Cannot Configure the Wireless Access Point from a Browser . . . . .134

When You Enter a URL or IP Address a Time-Out Error Occurs. . . . . . .135

Troubleshoot a TCP/IP Network Using the Ping Utility. . . . . . . . . . . . . . .135

Test the LAN Path to Your Wireless Access Point. . . . . . . . . . . . . . . .136

Test the Path from Your Computer to a Remote Device . . . . . . . . . . .137

Problems with Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137

Use the Packet Capture Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .138

Appendix A Supplemental Information

Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .139

Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .142

Appendix B Command-Line Reference

Appendix C Notification of Compliance

Index

1. Introduction

This chapter introduces the NETGEAR® ProSafe® Premium 3 x 3 Dual-Band Wireless-N

Access Point WNDAP620 and describes some of the key features. The chapter includes the

following sections:

•About the ProSafe Premium 3 x 3 Dual-Band Wireless-N Access Point WNDAP620

•What Is in the Box?

•System Requirements

•Key Features and Standards

•Hardware Description

•Register the Wireless Access Point

Note: For more information about the topics covered in this manual, visit

the Support website at http://support.netgear.com.

Note: Firmware updates with new features and bug fixes are made

available from time to time at downloadcenter.netgear.com. Some

products can regularly check the site and download new firmware,

or you can check for and download new firmware manually. If the

features or behavior of your product do not match what is described

in this guide, you might need to update your firmware.

About the ProSafe Premium 3 x 3 Dual-Band Wireless-N

Access Point WNDAP620

The ProSafe Premium 3 x 3 Dual-Band Wireless-N Access Point WNDAP620, going forward

in this manual referred to as the wireless access point, is a powerful building block of a

wireless LAN infrastructure. It provides either 2.4 GHz 802.11b/g/n or 5 GHz 802.11a/n

connectivity between wired Ethernet networks and radio-equipped wireless notebook

systems, desktop systems, print servers, and other devices. Support for three transmit radio

Introduction

ProSafe Premium 3 x 3 Dual-Band Wireless-N Access Point WNDAP620

chains and three receive radio chains, also referred to as 3x3 multiple input, multiple output

(MIMO), can increase wireless throughput considerably.

The wireless access point provides wireless connectivity to multiple wireless network devices

within a fixed range or area of coverage—interacting with a wireless network interface card

(NIC) through an antenna. Typically, an individual in-building wireless access point provides a

maximum connectivity area with about a 500-foot radius. The wireless access point can

support a maximum of 128 clients in a range of several hundred feet. The throughput is

shared between all clients. Make sure that you install a sufficient number of wireless access

points to meet the required coverage, throughput, and quality of your wireless network.

The wireless access point acts as a bridge between the wired LAN and wireless clients.

Connecting multiple wireless access points through a wired Ethernet backbone can further

increase the wireless network coverage. As a mobile computing device moves out of the

range of one wireless access point, it moves into the range of another. As a result, wireless

clients can freely roam from one wireless access point to another and still maintain a

seamless connection to the network.

The autosensing capability of the wireless access point allows packet transmission at up to

450 Mbps, or at reduced speeds to compensate for distance or electromagnetic interference.

Advanced wireless features that are supported on the wireless access point include a

wireless intrusion detection system (IDS), wireless intrusion prevention system (IPS), and

configurable wireless QoS policies.

You can manage the wireless access point from either an IPv4 or IPv6 address, and the

wireless access point can allocate either IPv4 or IPv6 DHCP addresses to its wireless clients.

What Is in the Box?

The product package contains the following items:

•ProSafe Premium 3 x 3 Dual-Band Wireless-N Access Point WNDAP620

•Power adapter and cord (12 VCD, 1.5A)

•Straight-through Category 5 Ethernet cable

•Installation guide

•Resource CD, which includes this manual

•Wall-mount kit made up of brackets and hardware

Contact your reseller or customer support in your area if there are any missing or damaged

parts.

See the NETGEAR website at http://support.netgear.com/general/contact/default.aspx for

the telephone number of customer support in your area. Keep the installation guide, along

with the original packing materials. If you need to return the wireless access point for repair,

use the packing materials to repack the wireless access point.

Introduction

ProSafe Premium 3 x 3 Dual-Band Wireless-N Access Point WNDAP620

System Requirements

Before installing the wireless access point, make sure that your system meets these

requirements:

•A 10/100/1000 Mbps local area network device such as a hub or switch

•The Category 5 UTP straight-through Ethernet cable with RJ-45 connector included in the

package, or one like it

•A 100–120V, 50–60 Hz AC power source

•A computer with the TCP/IP protocol installed and a web browser for configuration, such

as Microsoft Internet Explorer 6.0 or later, or Mozilla 1.5 or later

•An 802.11a/n- or 802.11b/g/n-compliant device, such as the NETGEAR N600 Wireless-N

Dual Band USB Adapter (WNDA3100)

Key Features and Standards

•Supported Standards and Conventions

•Key Features

•802.11b/g/n and 802.11a/n Standards–Based Wireless Networking

•Autosensing Ethernet Connections with Auto Uplink

The wireless access point is easy to use and provides solid wireless and networking support.

It also offers a wide range of security options.

Supported Standards and Conventions

The wireless access point supports the following standards and conventions:

•Standards compliance.The wireless access point complies with the IEEE 802.11a/b/g

standards for wireless LANs and is Wi-Fi certified for 802.11n standard.

•WPA and WPA2. The wireless access point provides WPA and WPA2 enterprise-class

strong security with RADIUS and certificate authentication as well as dynamic encryption

key generation. The WPA-PSK and WPA2-PSK pre-shared key authentication does not

have the overhead of RADIUS servers but provides the strong security of WPA.

•Multiple BSSIDs. The wireless access point supports multiple BSSIDs. When a wireless

access point is connected to a wired network and a set of wireless stations, it is called a

basic service set (BSS). The basic service set identifier (BSSID) is a unique identifier

attached to the header of packets sent over a WLAN that differentiates one WLAN from

another when a mobile device tries to connect to the network.

The multiple BSSID feature allows you to configure up to 16 SSIDs (8 per radio, but only

one radio can be active at a time) on your wireless access point and assign different

configuration settings to each SSID. All the configured SSIDs are active, and the network

devices can connect to the wireless access point by using any of these SSIDs.

Introduction

ProSafe Premium 3 x 3 Dual-Band Wireless-N Access Point WNDAP620

•DHCP server and client.The DHCP server of the wireless access point can provide a

dynamic IPv4 or IPv6 address to wireless clients. The wireless access point can also act

as a client and obtain an IPv4 or IPv6 address from a DHCP server on the LAN.

•SNMP.The wireless access point supports Simple Network Management Protocol

(SNMP) for Management Information Base (MIB) management.

•STP and LLDP. The wireless access point supports Spanning Tree Protocol (STP) and

Ethernet Link Layer Discovery Protocol (LLDP). LLDP is enabled by default.

•802.1Q VLAN. A network of computers can behave as if they are connected to the same

network even though they might actually be physically on different segments of a LAN.

Virtual LANs (VLANs) are configured through software rather than hardware, which

makes them very flexible. VLANs are very useful for user and host management,

bandwidth allocation, and resource optimization.

Key Features

The wireless access point provides solid functionality, including the following features:

•Dual band. The wireless access point can operate either in the 2.4 GHz band or the

5 GHz band. The choice of band is reflected in the wireless modes that you can select

and the administration screens that are displayed in the web management interface.

•IPv4 and IPv6. The wireless access point is manageable from either an IPv4 or IPv6

address, it can function as an IPv4 or IPv6 DHCP client, and its DHCP server can

allocate either IPv4 or IPv6 addresses.

•Multiple operating modes:

-Wireless access point. Operates as a standard 802.11b/g/n or 802.11a/n wireless

access point.

-Point-to-point bridge. In this mode, the wireless access point communicates only

with another bridge-mode wireless station or wireless access point. Network

authentication should be used to protect this communication.

-Point-to-multipoint bridge.Select this option only if this wireless access point is the

master for a group of bridge-mode wireless stations. The other bridge-mode wireless

stations send all traffic to this master and do not communicate directly with each

other. Network authentication should be used to protect this traffic.

-Repeater. In this mode, the wireless access point does not function as an access

point for clients but functions only in point-to-multipoint bridge mode to repeat the

wireless signal and send all traffic to a remote access point. Network authentication

should be used to protect this communication.

•WMM. Wi-Fi Multimedia (WMM) is a subset of the 802.11e standard. WMM allows

wireless traffic to have a range of priorities, depending on the kind of data.

Time-dependent information, like video or audio, has a higher priority than normal traffic.

For WMM to function correctly, wireless clients also need to support WMM.

Introduction

ProSafe Premium 3 x 3 Dual-Band Wireless-N Access Point WNDAP620

•QoS. Quality of Service (QoS) support lets you configure parameters that affect traffic

flowing from the wireless access point to the client station and traffic flowing from the

client station to the wireless access point:

-The QoS settings let you prioritize traffic, such as voice and video traffic, so that

packets do not get dropped.

-The QoS policies let you configure classifications (match clauses) and apply traffic to

eight priority queues based on IP precedence, DSCP, MAC address, IP address, and

other information that might be present in Layer 2 and Layer 3 packet headers.

•Wireless IDS/IPS. The wireless intrusion detection system (IDS) and intrusion prevention

system (IPS) can detect and prevent a variety of wireless attacks. Attacks are covered by

preconfigured policy rules. When an attack occurs, the wireless access point can notify a

network administrator though an email.

•Hotspot support. You can allow all HTTP (TCP, port 80) requests to be captured and

redirected to the URL you specify.

•Rogue AP and ad hoc network detection.Rogue AP filtering and ad hoc network

detection ensure that unknown APs and networks are not given access to any part of the

secured wireless and wired LAN.

•Access control.MAC address filtering can ensure that only trusted wireless stations can

use the wireless access point to gain access to the wireless and wired LAN.

•Security profiles.When using multiple BSSIDs, you can configure unique security

settings (encryption, SSID, and so on) for each BSSID.

•Hidden mode. The SSID is not broadcast, assuring that only clients configured with the

correct SSID can connect.

•Secure Telnet command-line interface. The secure Telnet command-line interface

(CLI) enables direct secure access over the serial port and easy scripting of configuration

of multiple wireless access points across an extensive network through the Ethernet

interface. A Secure Shell (SSH) client is required.

•Upgradeable firmware. Firmware is stored in a flash memory. You can upgrade it easily,

using only your web browser, and you can upgrade it remotely. You can also use the

command-line interface.

•Configuration backup. Configuration settings can be backed up to a file and restored.

•Secure and economical operation. Adjustable power output allows more secure or

economical operation.

•PoE support. Using Power over Ethernet (PoE), any 802.3af-compliant midspan or

end-span source can supply power to the wireless access point over its Ethernet port.

•Autosensing Ethernet connection with Auto Uplink™ interface. Connects to

10/100/1000 Mbps IEEE 802.3 Ethernet networks.

•LED indicators. Power/Test, Active, LAN, and WLAN for each radio mode are easily

identified.

•VLAN security profiles. Each security profile is automatically allocated a VLAN ID when

the security profile is modified.

Andere Handbücher für ProSafe Premium WNDAP620

Inhaltsverzeichnis

Andere NETGEAR Drahtloser Zugangspunkt Handbücher

NETGEAR

NETGEAR ME102 - Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR WG602 - 54 Mbps Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR ProSAFE WNDAP380R Bedienungsanleitung

NETGEAR

NETGEAR WG302 - 802.11g ProSafe Wireless Access... Bedienungsanleitung

NETGEAR

NETGEAR WAC124-100NAS Bedienungsanleitung

NETGEAR

NETGEAR Orbi RBE971 Bedienungsanleitung

NETGEAR

NETGEAR WNDR4300-TN Bedienungsanleitung

NETGEAR

NETGEAR ProSafe WG102-500 Bedienungsanleitung

NETGEAR

NETGEAR prosafe WAC740 Bedienungsanleitung

NETGEAR

NETGEAR WNTR2001 Bedienungsanleitung

NETGEAR

NETGEAR WAX202 Bedienungsanleitung

NETGEAR

NETGEAR WG602v2 - Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR ProSAFE WNDAP380R Bedienungsanleitung

NETGEAR

NETGEAR WN604 - Wireless-N 150 Access Point Bedienungsanleitung

NETGEAR

NETGEAR WAX638E Bedienungsanleitung

NETGEAR

NETGEAR Orbi Pro Satellite Bedienungsanleitung

NETGEAR

NETGEAR WG302 - 802.11g ProSafe Wireless Access... Bedienungsanleitung

NETGEAR

NETGEAR ProSAFE WNDAP380R Bedienungsanleitung

NETGEAR

NETGEAR WG602v4 - Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR WG102 - ProSafe Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR WAG302 - ProSafe Dual Band Wireless Access... Bedienungsanleitung

NETGEAR

NETGEAR WAC104 Bedienungsanleitung

NETGEAR

NETGEAR ME102 - Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR WG302 - 802.11g ProSafe Wireless Access... Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung