NETGEAR HE102 - Wireless Access Point Bedienungsanleitung

Preliminary

Access Point User’s Guide •Page 1

802.11a Wireless Access Point

Model HE102

User’s Guide

Rev 1.2.11

Preliminary

Page 2•Access point User’s Guide

Trademarks

NETGEAR is a registered trademark of NETGEAR, INC. Windows is a registered trademark of Microsoft

Corporation. Other brand and product names are trademarks or registered trademarks of their respective

In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the

right to make changes to the products described in this document without notice.

NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or

circuit layout(s) described herein.

FCC REGULATORY STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, with can be

determined by turning the equipment of and on, the user is encouraged to try to correct the interference by

on or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that which the receiver is

connected.

• Consult the dealer or an experienced radio/TXV technician for help.

Modifications made to the product, unless expressly approved by NETGEAR, INC., could void the

user’s authority to operate the equipment.

RF Exposure Requirements WARNING!!

To ensure compliance with FCC RF exposure requirements, the antenna used for this device must be

installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or

operating in conjunction with any other antenna or radio transmitter. Installers and end-users must follow

the installation instructions provided in this user guide.

Radio Frequency Interference Requirements

This device is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency range. FCC

requires this product to be used indoors for the frequency range 5.15 to 5.25 GHz to reduce the potential for

harmful interference to co-channel Mobile Satellite systems. High power radars are allocated as primary

users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with

and /or damage this device.

Preliminary

Access Point User’s Guide •Page 3

Table of Contents

1INTRODUCTION.....................................................................................................4

1.1 SCOPE .................................................................................................................. 4

1.2 FEATURES ............................................................................................................ 4

2GETTING TO KNOW THE MODEL HE102 ACCESS POINT........................5

2.1 FRONT VIEW ........................................................................................................ 5

2.2 REAR VIEW .......................................................................................................... 6

3AP NETWORK ATTACHMENT AND CONFIGURATION .............................8

3.1 AP NETWORK CONFIGURATION AND NETWORK BOOT........................................ 8

3.2 CONFIGURING THE AP THROUGH WEB BROWSER.............................................. 11

APPENDIX A—AP WEB SERVER .............................................................................16

INTRODUCTION .............................................................................................................. 16

ACCESSING THE AP WEB SERVER ................................................................................. 16

SETUP ............................................................................................................................ 18

WEP .............................................................................................................................. 20

Preliminary

Page 4•Access point User’s Guide

1Introduction

1.1 Scope

The intent of this document is to familiarize you with the NETGEAR Model HE102

Access Point (AP), its physical characteristics, setup, configuration, and usage.

1.2 Features

The Model HE102 Access Point is an IEEE 802.11a AP supporting up to 60 IEEE

802.11a station associations including the AP itself. Rates of 6 to 54 Mbps are supported

in standard IEEE 802.11a mode, and 12 to 72 Mbps in turbo mode. All transmission

rates are supported across the lower and middle bands of the 5 GHz spectrum(5.15 to

5.35 GHz).

Preliminary

Access Point User’s Guide •Page 5

2Getting to Know the Model HE102 Access Point

2.1 Front View

The Model HE102 Access Point (AP) has 3 LED’s, and a pair of side-mounted antennas

that rotate 180°for alternative reception positioning and compact packaging.

Table 1 –LED Functionality

LED 1 Description

Off No Power

On Power On and Ready for Operation

Blink Power On but Not Ready for Operation–at initial power on or reset, this

indicates self-test or software loading; at other times, this indicates a system fault

LED 1 (Power Status)

LED 2 (Ethernet Link)

LED 3 (Wireless Link)

Preliminary

Page 6•Access point User’s Guide

LED 2 Description

Off No Ethernet Link Detected

Green On 100 Mbps Link Detected but No Activity

Green Blink 100 Mbps Link Activity–blink rate is proportional to activity

Amber On 10 Mbps Link Detected but No Activity

Amber Blink 10 Mbps Link Activity–blink rate is proportional to activity

LED 3 Description

Off Wireless Link Disabled

Very Slow Blink Looking for Network Association

Slow Blink Associated with Network but No Activity

Fast Blink Associated with Network –blink rate is proportional to activity

2.2 Rear View

The rear panel of the AP has a console interface, a RJ-45 Ethernet jack, a restore-to-

default button, and a power supply connector,

45 Ethernet Jack

Restore to

Default Button

Power Supply

Connector

Preliminary

Access Point User’s Guide •Page 7

•The console connector is only used for system configuration during

manufacturing process and should not be connected.

•The RJ-45 Ethernet jack is provided for 10/100 Mbps connectivity to a wired

Ethernet LAN. The Ethernet jack is wired for direct connection to a Ethernet hub

or switch.

•The restore to default push button is to allow the Access Point to be reset back to

the factory default condition in the event that the Access Point is no longer

accessible or controllable through its web-based interface.

•A 3.3 V power supply is provided and is plugged into the power supply connector

of the AP.

Preliminary

Page 8•Access point User’s Guide

3AP Network Attachment and Configuration

3.1 AP Network Configuration and Network Boot

Figure 1 shows an example connection of the AP to a Host PC (HPC). Follow these steps

to establish the physical connections:

1. Connect the AP Ethernet port to the HPC Ethernet card through the Ethernet

hub/switch or an Ethernet crossover cable. An Ethernet switch/hub or crossover

cable is not included.

2. Plug in the 3.3 V power supply adapter (provided by NETGEAR) to the AP

power supply connector.

Figure 1 –Connection Between AP and Host PC

At this point, the Windows-based HPC needs the following configuration steps in order

to control the AP:

1. From the Start menu, choose Settings and open the Network and Dial-up

Connections window.

2. Right-click on the Local Area Network icon in the window, which belongs to the

Ethernet controller that is connected to the AP and select Properties.

Host PC

(HPC)

Ethernet Port

Ethernet Cable

HE102 Access Point

(AP)

Ethernet

Hub/Switch

Ethe

rnet

Port

Power

Supply

Ethernet Cable

Preliminary

Access Point User’s Guide •Page 9

3. Within the Local Area Connection Properties window, choose Internet Protocol

(TCP/IP) and click Properties.

Preliminary

Page 10 •Access point User’s Guide

4. Configure the IP address for the Ethernet connection in the Internet Protocol

(TCP/IP) Properties window. Click OK to continue, and close Local Area

Connection Properties. Note that this IP address is used by the HPC to access the

AP through the web-based interface via the Ethernet connection.

Andere Handbücher für HE102 - Wireless Access Point

Inhaltsverzeichnis

Andere NETGEAR Drahtloser Zugangspunkt Handbücher

NETGEAR

NETGEAR AirBridge WBC502 Bedienungsanleitung

NETGEAR

NETGEAR ME102 - Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR WAB102 - 802.11a+b Dual Band Wireless Access... Bedienungsanleitung

NETGEAR

NETGEAR WG103 ProSafe Bedienungsanleitung

NETGEAR

NETGEAR WAX206 Bedienungsanleitung

NETGEAR

NETGEAR prosafe WAC740 Bedienungsanleitung

NETGEAR

NETGEAR EX7000 Bedienungsanleitung

NETGEAR

NETGEAR Orbi RBE970B Bedienungsanleitung

NETGEAR

NETGEAR WAX615-100NAS Bedienungsanleitung

NETGEAR

NETGEAR WAX204 Bedienungsanleitung

NETGEAR

NETGEAR WAC124-100NAS Bedienungsanleitung

NETGEAR

NETGEAR Telstra Wi-Fi 4G Advanced II AirCard 790S Bedienungsanleitung

NETGEAR

NETGEAR WAG102 - ProSafe Dual Band Wireless Access... Bedienungsanleitung

NETGEAR

NETGEAR ME103 - 802.11b ProSafe Wireless Access... Bedienungsanleitung

NETGEAR

NETGEAR WNAP210 Bedienungsanleitung

NETGEAR

NETGEAR WAC720 Bedienungsanleitung

NETGEAR

NETGEAR WAC510 Bedienungsanleitung

NETGEAR

NETGEAR WAX214v2 Bedienungsanleitung

NETGEAR

NETGEAR WN802T Bedienungsanleitung

NETGEAR

NETGEAR ME102 - Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR WN802Tv2 - Wireless-N Access Point Bedienungsanleitung

NETGEAR

NETGEAR WAC104 Bedienungsanleitung

NETGEAR

NETGEAR WG302v2 - ProSafe 802.11g Wireless Access... Betriebsanleitung

NETGEAR

NETGEAR ProSafe Premium WNDAP620 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung