NETGEAR WG102 - ProSafe Wireless Access Point Bedienungsanleitung

)NSTALLATION'UIDE

NETGEAR WG102 ProSafe 802.11g Wireless Access Point

Start Here

Please refer to the Reference Manual on your Resource CD for instructions on advanced

configuration options.

Estimated Completion Time: 30 minutes.

Tip: Before mounting the WG102 in a high location, first set up and test the WG102 to

verify wireless network connectivity.

First, Set Up the WG102

1. Connect the wireless access point to your computer.

a. Unpack the box and verify the contents.

b. Prepare a PC with an Ethernet

adapter. If this PC is already part

of your network, record its

TCP/IP configuration settings.

Configure the PC with a static IP

address of 192.168.0.210 and

255.255.255.0 as the Subnet Mask.

c. Connect an Ethernet cable from

the WG102 to the PC (point A in

the illustration).

d. Securely insert the other end of the

cable into the WG102 Ethernet

port (point B in the illustration).



(WKHUQHW

3RUW

%OXH1(7*($5

&DEOH

:*

&RPSXWHU

e. Turn on your computer, connect the power adapter to the WG102 and verify the

following:

•Power: The power light should be lit. If the power light is not lit, check the

connections and check to see if the power outlet is controlled by a wall

switch that is turned off.

•Te s t : The test light blinks when the WG102 is first turned on.

•LAN: The LAN light on the WG102 should be lit (amber for a 10 Mbps

connection and green for a 100 Mbps connection). If not, make sure the

Ethernet cable is securely attached at both ends.

•Wireless: The WLAN light should be lit.

2. Configure LAN and wireless access.

a. Configure the WG102 Ethernet port for LAN access.

• Connect to the WG102 by opening your browser and

entering http://192.168.0.229 in the address field.

• When prompted, enter admin for the user name and

password for the password, both in lower case letters.

• Click the Basic Settings link and configure the IP Settings for your network.

b. Configure the wireless interface for wireless access. See the online help or the

Reference Manual for full instructions.

c. Test wireless connectivity using a PC with a wireless adapter configured

according to the wireless settings you just set in the WG102 to establish a

wireless connection to the WG102.

Now that you have finished the setup steps, you are ready to deploy the WG102 in

your network. If needed, you can now reconfigure the PC you used in step 1 back to

its original TCP/IP settings.

Deploy the WG102

1. Disconnect the WG102 and position it where you will deploy it. The best location is

elevated, such as wall mounted or on the top of a cubicle, at the center of your

wireless coverage area, and within line of sight of all the mobile devices.

2. Position the antenna. Vertical positioning provides best side-to-side coverage.

Horizontal positioning provides best top-to-bottom coverage.

3. Connect an Ethernet cable from your WG102 Access Point to a LAN port on your

router, switch, or hub.

4. Connect the power adapter to the wireless access point and plug the power adapter in

to a power outlet. The PWR, LAN, and Wireless LAN lights should light up.

Tip: The WG102 supports Power Over Ethernet (PoE). If you have a switch that

provides PoE, you will not need to use the power adapter to power the WG102. This

can be especially convenient when the WG102 is installed in a high location far away

from a power outlet.

Now, Verify Wireless Connectivity

Using a computer with an 802.11g or 802.11b wireless adapter, verify connectivity by

using a browser such as Netscape® or Internet Explorer to connect to the Internet, or

check for file and printer access on your network.

Note: If you cannot connect, see to Troubleshooting Tips in this guide or the Reference

Manual on the Resource CD for ProSafe Wireless Access Point.

2005-11

Troubleshooting Tips

Here are some tips for correcting simple problems you may have.

No lights are lit on the access point.

The access point has no power.

• Make sure the power cord is connected to the access point and plugged in to a

working power outlet or power strip.

• Make sure you are using the correct NETGEAR power adapter

supplied with your access point.

The Ethernet light is not lit.

There is a hardware connection problem.

• Make sure the cable connectors are securely plugged in at the access point and the

network device (hub, switch, or router).

• Make sure the connected device is turned on.

The WLAN light is not lit.

The access point’s antennas are not working.

• If the Wireless LAN activity light stays off, disconnect the adapter from its power

source and then plug it in again.

• Make sure the antennas are tightly connected to the WG102.

• Contact NETGEAR if the Wireless LAN light remains off.

I cannot configure the access point from a browser.

Check these items:

• The WG102 is properly installed, LAN connections are OK, and it is powered on.

Check that the LAN port LED is green to verify that the Ethernet connection is OK.

• If you are using the NetBIOS name of the WG102 to connect, ensure that your PC

and the WG102 are on the same network segment or that there is a WINS server on

your network.

• If your PC uses a Fixed (Static) IP address, ensure that it is using an IP Address in the

range of the WG102. The WG102 default IP Address is 192.168.0.229 and the default

Subnet Mask is 255.255.255.0. The WG102 default setting is for a static IP address. If

the network where you are connecting it is using DHCP, configure it accordingly. See

the Reference Manual on the Resource CD for ProSafe Wireless Access Point for

more details.

I cannot access the Internet or the LAN with a wireless capable

computer.

There is a configuration problem. Check these items:

• You may not have restarted the computer with the wireless adapter to have TCP/IP

changes take effect. Restart the computer.

• The computer with the wireless adapter may not have the correct TCP/IP settings to

communicate with the network. Restart the computer and check that TCP/IP is set up

properly for that network. The usual setting for Windows on the Network Properties

is set to “Obtain an IP address automatically.”

• The access point’s default values may not work with your network. Check the access

point default configuration against the configuration of other devices in your network.

• For full instructions on changing the access point’s default values,

see the Reference Manual on the Resource CD for ProSafe Wireless Access Point.

Technical Support

Thank you for selecting NETGEAR products.

To register your product, go to: http://www.NETGEAR.com/register

Go to http://www.NETGEAR.com/support for support information.

This symbol was placed in accordance with the European Union Directive 2002/96 on the Waste

Electrical and Electronic Equipment (the WEEE Directive). If disposed of within the European Union,

this product should be treated and recycled in accordance with the laws of your jurisdiction

implementing the WEEE Directive.

NETGEAR is a registered trademark of NETGEAR, Inc. in the United States and/or other countries. Other brand

and product names are trademarks or registered trademarks of their respective holders. Information is subject to

change without notice.

Andere Handbücher für WG102 - ProSafe Wireless Access Point

Inhaltsverzeichnis

Andere NETGEAR Drahtloser Zugangspunkt Handbücher

NETGEAR

NETGEAR ProSafe Premium WNDAP660 Bedienungsanleitung

NETGEAR

NETGEAR Telstra Wi-Fi 4G Advanced II AirCard 790S Bedienungsanleitung

NETGEAR

NETGEAR prosafe WAC740 Bedienungsanleitung

NETGEAR

NETGEAR WG602v4 - Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR ProSafe WNAP320 Bedienungsanleitung

NETGEAR

NETGEAR WNDR4300-TN Bedienungsanleitung

NETGEAR

NETGEAR WAX618 Bedienungsanleitung

NETGEAR

NETGEAR WN804 Bedienungsanleitung

NETGEAR

NETGEAR WG102 - ProSafe Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR WG602v4 - Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR WG102 - ProSafe Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR WAC124 Bedienungsanleitung

NETGEAR

NETGEAR ME102 - Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR WN802T Bedienungsanleitung

NETGEAR

NETGEAR Orbi PRO SRS60 Bedienungsanleitung

NETGEAR

NETGEAR WiFi 6 AX1800 Bedienungsanleitung

NETGEAR

NETGEAR WN802Tv2 - Wireless-N Access Point Bedienungsanleitung

NETGEAR

NETGEAR HE102 - Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR WAX610 Bedienungsanleitung

NETGEAR

NETGEAR WAX204 Bedienungsanleitung

NETGEAR

NETGEAR WAX204 Bedienungsanleitung

NETGEAR

NETGEAR PowerLine XWNB5602 Bedienungsanleitung

NETGEAR

NETGEAR WG103 ProSafe Bedienungsanleitung

NETGEAR

NETGEAR SSL312 - ProSafe SSL VPN Concentrator 25 Montage- und Wartungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung