Netvox R313DA Bedienungsanleitung

Model：R313DA

Wireless Vibration Sensor, Rolling Ball Type

Wireless Vibration Sensor,

Rolling Ball Type

R313DA

User Manual

This document contains proprietary technical information which is the property of NETVOX Technology. It shall be maintained

in strict confidence and shall not be disclosed to other parties, in whole or in part, without written permission of NETVOX

Technology. The specifications are subject to change without prior notice.

Table of Content

1. Introduction.............................................................................................................................................................2

2. Appearance..............................................................................................................................................................3

3. Main Features..........................................................................................................................................................3

4. Set up Instruction ....................................................................................................................................................4

5. Data Report .............................................................................................................................................................5

6. Installation...............................................................................................................................................................9

7. Important Maintenance Instruction.........................................................................................................................9

1. Introduction

R313DA is a wireless long-distance ball-type vibration device that is a Class A device based on the LoRaWANTM protocol of

NETVOX. It is compatible with the LoRaWAN protocol.

LoRa Wireless Technology:

LoRa is a wireless communication technology famous for its long-distance transmission and low power consumption. Compared

with other communication methods, LoRa spread spectrum modulation technique greatly extend the communication distance. It

can be widely used in any use case that requires long-distance and low-data wireless communications. For example, automatic

meter reading, building automation equipment, wireless security systems, industrial monitoring. It has features like small size,

low power consumption, long transmission distance, strong anti-interference ability and so on.

LoRaWAN:

LoRaWAN uses LoRa technology to define end-to-end standard specifications to ensure interoperability between devices and

gateways from different manufacturers.

2. Appearance

3. Main Features

Compatible with LoRaWAN

2 sections of 3V CR2450 button battery power supply

Vibration status detection

Simple operation and setting

Protection level IP30

Compatible with LoRaWANTM Class A

Frequency hopping spread spectrum

Configuration parameters can be configured via a third-party software platform, data can be read and alerts can be set via

SMS text and email (optional)

Applicable to third-party platforms: Actility/ThingPark, TTN, MyDevices/Cayenne

Low power consumption and long battery life

Note:

Battery life is determined by the sensor reporting frequency and other variables, please refer to

http://www.netvox.com.tw/electric/electric_calc.html

On this website, users can find battery life time for varied models at different configurations.

Indicator

Function Key

4.Set up Instruction

On/Off

Power on

Insert batteries (user may need a screwdriver to open)

Insert 2 x 3V CR2450 button batteries into the battery slot in the correct direction and close the

back cover.

Note: Require 2 button batteries to supply power at the same time.

Turn on Press any function key till the green and red indicator flashes once.

Turn off

(Restore to factory setting)

Press and hold two function keys for 5 seconds and the green indicator flashes 20 times.

Power off Remove Batteries.

Note:

1. Remove and reinsert the battery: the device will remember the previous on/off status by

default.

2. After insert batteries and press the button at the same time, the device will be in engineering

testing mode.

3. On/off interval is suggested to be about 10 seconds to avoid the interference of capacitor

inductance and other energy storage components.

Network Joining

Never joined the network

Turn on the device to search the network to join.

The green indicator stays on for 5 seconds: success

The green indicator remains off: fail

Had joined the network

Turn on the device to search the previous network to join.

The green indicator stays on for 5 seconds: success

The green indicator remains off: fail

Fail to join the network

(when the device is on)

Suggest to check the device verification information on the gateway or consult your platform

server provider.

Function Key

Press and hold for 5 seconds

Restore to factory setting / Turn off

The green indicator flashes 20 times: success

The green indicator remains off: fail

Press once The device is in the network: the green indicator flashes once and sends a report

The device is not in the network: the green indicator remains off

Sleeping Mode

The device is on and in the

network

Sleeping period: Min Interval.

When the reportchange exceeds setting value or the state changes: send a data report according

to Min Interval.

Low Voltage Warning

Low Voltage 2.4V

5. Data Report

Data report configuration and sending period are as following:

Min Interval

(Unit:second)

Max Interval

(Unit:second) Reportable Change Current Change≥

Reportable Change

Current Change＜

Reportable Change

Any number between

1~65535

Any number between

1~65535 Can not be 0. Report

per Min Interval

Report

per Max Interval

When the device is turned on, it will immediately send a version package and an attribute report data.

The device sends data according to the default configuration before any other configuring.

Default setting:

Maximum time: 3600s

Minimum time: 3600s (Default: Every Min Interval will detect the state of the dry contact one time)

BatteryChange: 0x01 (0.1V)

(If there are special customized shipments, the settings will be changed according to customer’s requirement.)

R313DAtrigger:

When the device senses vibration and the ball is shaken, an alarm message will be reported.

The shaking alarm bit is “1”.

The static and non-shaking alarm bit is “0”.

Restore Function:

There are two ways for the ball to trigger an alarm.

One is not to report the recovery status after sending the alarm. (default)

The other is to report the recovery status after the device stops vibrating for 5 seconds after sending the alarm.

The two ways can be executed before shipment or by LoRaWan command configuration

Note:

The interval between two reports must be the MinTime.

The reported data is decoded by the Netvox LoRaWAN Application Command document and

http://loraresolver.netvoxcloud.com:8888/page/index

Example of ConfigureCmd

FPort：0x07

Bytes 1 1 Var (Fix =9 Bytes)

CmdID DeviceType NetvoxPayLoadData

CmdID– 1 byte

DeviceType– 1 byte – Device Type of Device

NetvoxPayLoadData– var bytes (Max=9bytes)

Description Device Cmd

Device

Type NetvoxPayLoadData

ConfigReport

Req

R313

0x01

0xA8

MinTime

(2bytes Unit: s)

MaxTime

(2bytes Unit: s)

BatteryChange

(1byte Unit: 0.1v)

Reserved

(4Bytes, Fixed 0x00)

ConfigReport

Rsp 0x81 Status

(0x00_success)

Reserved

(8Bytes, Fixed 0x00)

ReadConfig

ReportReq 0x02 Reserved

(9Bytes, Fixed 0x00)

ReadConfig

ReportRsp 0x82 MinTime

(2bytes Unit: s)

MaxTime

(2bytes Unit: s)

BatteryChange

(1byte Unit: 0.1v)

Reserved

(4Bytes, Fixed 0x00)

(1) Command Configuration:

MinTime = 1min、MaxTime = 1min、BatteryChange = 0.1v

Downlink：01A8003C003C0100000000 // 003C(Hex) = 60(Dec)

Response：

81A8000000000000000000 (Configuration success)

81A8010000000000000000 (Configuration failure)

(2) Read Configuration:

Downlink：02A8000000000000000000

Response：824E003C003C0100000000 (Current configuration)

Restore function configuration

Description Device CmdID Device

Type NetvoxPayLoadData

SetRestore

ReportReq

R313DA

0x03

0xA8

RestoreReportSet

(1byte)

0x00_DO NOT report when sensor restore,

0x01_DO report when sensor restore)

Reserved

(8Bytes, Fixed 0x00)

SetRestore

ReportRsp 0x83 Status

(0x00_success)

Reserved

(8Bytes, Fixed 0x00)

GetRestore

ReportReq 0x04 Reserved

(9Bytes, Fixed 0x00)

GetRestore

ReportRsp 0x84

RestoreReportSet (1byte,

0x00_DO NOT report when sensor restore,

0x01_DO report when sensor restore)

Reserved

(8Bytes, Fixed 0x00)

(3) Do report after sensor stops vibrating

Downlink：03A8010000000000000000 (0x01_DO report when sensor restore)

Response：

83A8000000000000000000 (Configuration success)

83A8010000000000000000 (Configuration failure)

(2) Read restore function:

Downlink：04A8000000000000000000

Response：84A8010000000000000000 (Current configuration) (report when sensor restore)

Example for MinTime/MaxTime logic:

Example#1 based on MinTime = 1 Hour, MaxTime= 1 Hour, Reportable Change i.e. BatteryVoltageChange=0.1V

Max Time Max Time

Sleeping (Min Time) Sleeping (Min Time)

1H 2H 3H

Wake up and

collects data

REPORTS 2.8V

Wakes up and

collects data

REPORTS 2.8V

Wakes up and

collects data

REPORTS 2.8V

Note:

MaxTime=MinTime. Data will only be report according to MaxTime (MinTime) duration regardless BatteryVoltageChange

value.

Example#2 based on MinTime = 15 Minutes, MaxTime= 1 Hour, Reportable Change i.e. BatteryVoltageChange= 0.1V.

MaxTime

Sleeping (MinTime) sleeping sleeping sleeping

0H 15th M 30th M 45th M 1H 2H

Example#3 based on MinTime = 15 Minutes, MaxTime= 1 Hour, Reportable Change i.e. BatteryVoltageChange= 0.1V.

MaxTime

sleeping sleeping ...

0H 15th M 30th M 45th M 1H 1H 10th M 1H 25th M 1H 40th M 1H 55th M 2H 10th M

Note:

1) The device only wakes up and performs data sampling according to MinTime Interval. When it is sleeping, it does not collect

data.

2) The data collected is compared with the last data reported. If the data change value is greater than the ReportableChange value,

the device reports according to MinTime interval. If the data variation is not greater than the last data reported, the device

reports according to MaxTime interval.

3)We do not recommend to set the MinTime Interval value too low. If the MinTime Interval is too low, the device wakes up

frequently and the battery will be drained soon.

4) Whenever the device sends a report, no matter resulting from data variation, button pushed or MaxTime interval, another cycle

of MinTime / MaxTime calculation is started.

Wakes up and

collects data

2.8V

Does not report

Wakes up and

collects data

REPORTS 2.8V

Wakes up and

collects data

REPORT 2.8V

Wakes up and

collects data

REPORTS

2.8V

Wakes up and

collects data

2.7V |2.7-2.8|=0.1

REPORTS 2.7V

Wakes up and

collects data

2.7V

Does not report

Wakes up and

collects data

2.7V

Does not report

Wakes up and

collects data

2.7V

Does not report

Wakes up and

collects data 2.7V

Does not report

Wakes up and

collects data

2.7V

Does not report

Wakes up and

collects data

REPORTS

2.7V

Wakes up and

collects data

2.8V

Does not report

Users push the button,

REPORTS 2.7V.

Recalculate MaxTime.

Wakes up and

collects data

2.8V

Does not report

Wakes up and

collects data

2.8V

Does not report

6. Installation

(1) The device does not have a waterproof function. After the configuration of joining the network is completed, please place it

indoors.

(2) The dust at the installation location should be wiped clean before paste the device.

(3) The battery installation method is as the figure below. (the battery with the "+" side facing up)

Note: The user may need a screwdriver to open the cover.

7. Important Maintenance Instruction

Kindly pay attention to the following in order to achieve the best maintenance of the product:

•Keep the equipment dry. Rain, moisture and various liquids or water may contain minerals that can corrode

electronic circuits. In case the device is wet, please dry it completely.

•Do not use or store in dusty or dirty areas. This way can damage its detachable parts and electronic components.

•Do not store in excessive heat place. High temperatures can shorten the life of electronic devices, destroy batteries,

and deform or melt some plastic parts.

•Do not store in excessive cold place. Otherwise, when the temperature rises to normal temperature, moisture will form

inside which will destroy the board.

•Do not throw, knock or shake the device. Treating equipment roughly can destroy internal circuit boards

and delicate structures.

•Do not wash with strong chemicals, detergents or strong detergents.

•Do not paint the device. Smudges can make debris block detachable parts up and affect normal operation.

•Do not throw the battery into the fire to prevent the battery from exploding. Damaged batteries may also explode.

All the above suggestions apply equally to your device, batteries and accessories.

If any device is not operating properly.

Please take it to the nearest authorized service facility for repairing.

Inhaltsverzeichnis

Andere netvox Zubehör Handbücher

netvox

netvox RA0711 Bedienungsanleitung

netvox

netvox R718EB Bedienungsanleitung

netvox

netvox R718VA Bedienungsanleitung

netvox

netvox R72632A Bedienungsanleitung

netvox

netvox Contact Sensor Series Bedienungsanleitung

netvox

netvox R313FA1 Bedienungsanleitung

netvox

netvox RB11E Bedienungsanleitung

netvox

netvox R72615 Bedienungsanleitung

netvox

netvox R718PB15 Bedienungsanleitung

netvox

netvox ZigBee ZB11B Bedienungsanleitung

netvox

netvox R718PA Series Bedienungsanleitung

netvox

netvox R718CXAB Bedienungsanleitung

netvox

netvox R718AD Bedienungsanleitung

netvox

netvox Z713 Bedienungsanleitung

netvox

netvox R718PA11 Bedienungsanleitung

netvox

netvox ZB11A1 Bedienungsanleitung

netvox

netvox R718PA2 Bedienungsanleitung

netvox

netvox R816B01 Bedienungsanleitung

netvox

netvox R313CA Bedienungsanleitung

netvox

netvox RA0716 Bedienungsanleitung

netvox

netvox R313WA Bedienungsanleitung

netvox

netvox R718PB15 Bedienungsanleitung

netvox

netvox R313DB Bedienungsanleitung

netvox

netvox R816B Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

netvox R313DA Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken