Nexa AGWAGON C188 Bedienungsanleitung

SEMI SCALE MODEL 60 Class

90 Class

2-cycle engine

4-cycle engine

SPECIFICATIONS

Wingspan 1920mm

Length 1300mm

Electric Motor 1000 Watt (BOOST 90)

Glow Engine .60 2-T / .90 4-T

Radio 6 Channel / 8 Servos

WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and

cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.

Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.

ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,

die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann

hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um

professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist

durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.

TECHNISCHE DATEN

Spannweiter 1920mm

Lange 1300mm

Elektroantrieb 1000 Watt (BOOST 90)

Verbrennerantrieb 10cc 2-T / 15cc 4-T

Fernsteuerung 6 Kanal / 8 Servos

MONTAGEANLEITUNG

INSTRUCTION MANUAL

Or Electric equivalent

C188

70mm Spinner

.........................................................

1.5mm

L/R

Assemble left and right

sides the same way.

Drill holes using the stated

size of drill

(in this case 1.5 mm Ø)

Use epoxy glue

Take particular care here Hatched-in areas:

remove covering

film carefully

Not included.

These parts must be

purchased separately

Check during assembly that these

parts move freely, without binding

Apply cyano glue

SILICON

EPOXY A

EPOXY B

Epoxy Glue (30 minutes type)

Silicon Glue

Cyanoacrylate Glue

Sekundenkleber

Epoxy-Klebstoff (30min)

Minimum 6 channel radio

for airplane

.90 cu.in (8.5cc)

Extension cord

.60 cu.in. (7.5cc)

REQUIRED FOR OPERATION (Purchase separately)

Minimum 6 Kanal

Fernsteuerung

Servoverlangerungskabel

BENOTIGTE KOMPONENTEN (Nicht im Lieferumfang enthalten)

Brushless Motor

900-1000Watt

Brushless ESC

Brushless Regler

Silikonkleber

Tool Required/ Erfoderliches Werkzeug

CONVERSION TABLE

1.0mm = 3/64”

1.5mm = 1/16”

2.0mm = 5/64”

2.5mm = 3/32”

3.0mm = 1/8”

4.0mm = 5/32”

5.0mm = 13/64”

6.0mm = 15/64”

10mm = 13/32”

12mm = 15/32”

15mm = 19/32”

20mm = 51/64”

25mm = 1”

30mm = 1-3/16”

45mm = 1-51/64”

If exposed to direct sunlight and/or heat, wrinkles can appear. Storing the

model in a cool place will let the wrinkles disappear. Otherwise, remove

wrinkles in covering film with a hair dryer, starting with

low temperature. You can fix the corners by using a hot iron.

Bei Sonneneinstrahlung und/oder Wärme kann die Folie erschlaffen bzw. Falten

entstehen. Verwenden Sie ein Warumluftgebläse (Haartrockner) um evtl. Falten aus der Folie

zu bekommen. Die Kanten können Sie mit einem Bügeleisen behandeln. Nicht zuviel Hitze anwenden ! Low seting

www.motionrc.com

Trial fit the horizontal stabilizer in place on the fuselage. Check the alignment of the

horizontal stabilizer by measuring from a fixed point along the center line of the fuselage

to the leading edge on each side of the horizontal stabilizer. The distance must be equal on both sides.

When you are satisfied with the alignment, use

a pencil to trace around the top and bottom of

the stabilizer where it meets the fuselage.

Cut away only

the covering

both sides.

Remove the horizontal stabilizer from the

fuselage. Using a straight edge and a

sharp hobby knife, carefully cut away

the covering inside the lines which were

marked above. Be cautious not to cut

into the wood-this will weaken the

structure.

Cut away only the covering

Aluminum wing joiner

Cut away only the covering

BB’

B=B’

AA’

A=A’

Horizontal stabilizer

Aluminum wing joiner

Fuselage - rear view

When viewing visually from the back of the fuselage,

the aluminum wing joiner should be parallel to the

horizontal stabilizer (A=A’).

C188 1- Horizontal stabilizer

Step 1

Step 2

Step 3

Step 4

Install the horizontal stabilizer onto the fuselage and adjust

the alignment as described in steep 2.

Note: it is important to ensure that the horizontal stabilizer

is also level in regards to the fuselage.

Apply the thin CA along the area where the covering was

removed in the previous step and to the fuselage where the

horizontal stabilizer mounts .

! Securely glue together. If coming off during fly, you lose control of your air plane.

Apply thin CA glue into the slot where

the fuselage meet the horizontal stabilizer.

A A’

A=A’

Trial fit the vertical fin in position (2A).

Using a 90 degree triangle, ensure that the

vertical stabilizer is perpendicular to the

horizontal stabilizer (2B).

Using a pencil, trace around the vertical

stabilizer where it meets the fuselage, then

remove the vertical stabilizer from the fuselage.

Apply CA glue

both sides.

(thin CA)

90 degree

triangle

C188 2- Horizontal stabilizer

Step 5

C188 3- Vertical stabilizer

Step 1

Step 2

Remove the vertical stabilizer from the fuselage.

Using s sharp hobby knife, carefully cut away the

covering below the lines which were drawn in the

previous steep. Do not cut into the woods as this

will affect the structural integrity of the stabilizer .

Insert the vertical fin into the fuselage, precisely align

the vertical stabilizer as described in step 2.

Apply the thin CA glue on the vertical stabilizer where it

contacts the fuselage.

! Securely glue together. If coming off during fly,

you lose control of your air plane.

Cut away only

the covering

both sides.

Without using glue yet, push the elevator and its

hinges into the hinge slots in trailing edge of the

horizontal stabilizer .

Do the same way with the bottom side of elevator and

with the second elevator and rudder.

Apply thin CA glue on

the top and bottom of

the hinges.

Hinge / Scharnier

STABILIZER

Apply CA glue

both sides.

(thin CA)

Apply CA glue

both sides of

the hinges.

(thin CA)

Securely glue together. If coming off during flight,

you lose control of your air plane.

C188 4- Vertical stabilizer

Step 3

Step 4

C188 5- Elevator

Drill a 2.5mm diameter hole in torque rod mounting slot,

marking sure that you drill the hole perpendicular to the leading

edge of the rudder.

Position of the hole is 38mm (+/- 1mm) from the bottom edge of the rudder.

38mm

Test-fit the torque rod into the rudder.

When satisfied with the fit and alignment, remove the torque rod.

Hinge the rudder to the vertical stabilizer, using the thin CA glue. Make sure

to apply a thin CA glue to the left and right of both hinges and to the

inside the torque rod mounting slot and to the end of the torque rod itself.

2.5mm

Hinge / Scharnier STABILIZER

Apply the thin CA both the

left and right of the hinges

and hinge slots.

Tail wheel control arm

Tail wheel push-rod

1- Insert the tail wheel pushrod into the hole on the tail wheel control arm (as show).

2- Re-install the rudder torque rod and tail wheel mount in place.

3- Secure the tail wheel mount in place using four 3x12mm screws.

Secure the tail wheel control horn in place using a 3mm hex bolt set, Ensure smooth non-binding movement.

Test-fit the rudder torque

rod into the slot.

Rudder torque rod

NOTE: You may need to open up the slots so

that the torque rod bearing are not too difficult

to push in

3x12mm screw

...........4

Securely glue together. If coming off during flight, you lose control of

your air plane.

C188 6- Tail wheel

C188 7- Tail wheel

Note: All holes on the fuselage and bilnd-nuts

are pre-installed at factory.

...2

4X40mm bolt

4mm nut

............4

............6

4mm washer

90mm wheel

...2 4mm nut

4x45mm bolt

Aluminum landing gear

4mm nut

4x15mm hexagonal bolt

and nut .......................6

4x15mm hexagonal bolt

Aluminum landing gear

Aluminum Haupfahrwerk

C188 8- Main gear

C188 9- Main wheel

Rudder servo Elevator servo

Nylon pushrod guide

Rudder and tail wheel pushrod

.........2 set

.......2

TOP VIEW / Draufsicht

BOTTOM - VIEW / Unteransicht

Throttle servo

3mm plywood throtle

servo mount.

3mm plywood throtle

servo mount.

Secure throttle in place

using thin CA glue.

Connector

.....1

.....2

Elevator pushrod

Control horn

2x950mm rod / Clevis

2x900mm rod with Z bend

one end.

.......1

C188 10- Linkages

120mm

Position the engine to the engine mounts

so the distance from the prop hub to the

fire-wall is 120mm.

Mark the engine mounting plate where the

four holes are to be drilled.

! Align the mark on both engine mount

beams with the mark on the fire-wall

B’

FIRE-WALL

M: Mark on the fire-wall

B must be equal to B’ (B=B’)

Attach the engine mount beams onto the fire-wall

so the distance between of two engine mount beams

is “A”,and B=B’ as show.

Secure the engine mount beams onto the fire-wall

with litter CA glue

Using a pencil or felt tipped pen, mark the fire wall

where the four holes are to be drilled.

Carefully remove the engine mount beams

and drill a 6mm hole through the fire-wall

at each of the four marks made above.

6mm

Reposition the engine mount beams on to the fire-wall and

secure them with four 4x25mm hexagonal bolts.

Insert the blind-nut onto each of the four holes make above.

...................4

....................4

4x25mm hexagonal bolt - washer

Blind-nut

C188 11- Glow engine

Step 1

Step 2

Step 3

Step 4

FUEL TANK

SIDE-VIEW / Seitenansicht

Remove the engine and drill a 3mm holes through the

beam at each of the four marks made above.

Marking sure that you drill the hole perpendicular to the

beam of the engine mount.

3mm

Reposition the engine on the engine mount

beams, aligning it with the holes. Secure the

engine to the engine mount using four

3x25mm hexagonal bolts.

Note: Apply Silicon sealer to each of the

3x25mm bolt and nut.

.......4

3x25mm hexagonal bolt

Washer .......4

To muffler

Filler tube

To engine

After confirming the direction . Insert and tighten the

screw.

3x35 mm screw

4mm

C188 12- Glow engine

Step 5

Step 6

C188 13- Fuel tank

Inhaltsverzeichnis

Andere Nexa Spielzeug Handbücher

Nexa

Nexa P-38 Lightning Bedienungsanleitung

Nexa

Nexa MITSUBISHI A6M5 ZERO Bedienungsanleitung

Nexa

Nexa Pilatus Porter PC-6 Bedienungsanleitung

Nexa

Nexa BEECHCRAFT T-34C TURBO MENTOR MILITARY... Bedienungsanleitung

Nexa

Nexa Pilatus Porter PC-6 Bedienungsanleitung

Nexa

Nexa CE-208 Bedienungsanleitung

Nexa

Nexa NE-1 NAVY CUB Bedienungsanleitung

Nexa

Nexa DORNIER DO-27 Bedienungsanleitung

Nexa

Nexa Tri-Pacer Piper PA-22 Bedienungsanleitung

Nexa

Nexa Focke Wulf FW-190A Bedienungsanleitung

Nexa

Nexa Dago red Unlimited Air Racer 4 Bedienungsanleitung

Nexa

Nexa U.S NAVY DIVE BOMBER SBD-5 DAUNTLESS Bedienungsanleitung

Nexa

Nexa YAK-9 Bedienungsanleitung

Nexa

Nexa CURTISS P-40 Bedienungsanleitung

Nexa

Nexa P-39 Q/N AIRACOBRA Bedienungsanleitung

Nexa

Nexa MACCHI MC 205 Bedienungsanleitung

Nexa

Nexa Royal Air Force Supermarine Spitfire Bedienungsanleitung

Nexa

Nexa MESSERSCHMITT Me-109 Bedienungsanleitung

Beliebte Spielzeug Handbücher anderer Marken

marklin

marklin 37321 Bedienungsanleitung

Canon

Canon PAPER CRAFT Bedienungsanleitung

GREAT PLANES

GREAT PLANES Pitts M-12S Bedienungsanleitung

NOCH

NOCH 14261 Bedienungsanleitung

Hausler

Hausler 450 SE V2 Bedienungsanleitung

Dynaflite

Dynaflite Daydream Bedienungsanleitung

Kenner

Kenner Batman 63651 Bedienungsanleitung

LEGO

LEGO 8527 Bedienungsanleitung

Multiplex

Multiplex EasyStar II Bedienungsanleitung

iKarus

iKarus ECO 8 Bedienungsanleitung

Walkera

Walkera 38 Bedienungsanleitung

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Bedienungsanleitung

MD MXION SWD Bedienungsanleitung

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Bedienungsanleitung

marklin

marklin 39671 Bedienungsanleitung

LEGO

LEGO TECHNIC 8735 Bedienungsanleitung

Mattel

Mattel HOTWHEELS DWL04 Bedienungsanleitung

REVELL

REVELL Bristol Beaufighter TF.X Bedienungsanleitung