Nexa DORNIER DO-27 Bedienungsanleitung

DORNIER

Radio control model

R/C Flugmodell

MONTAGEANLEITUNG

INSTRUCTION MANUAL

SPECIFICATIONS

Wingspan 63 in.

Length 47.6 in.

Electric Motor (See next page)

Glow Engine .46 2Stroke / .52 4-Stroke

Radio 6 Channel / 6-7 Servos

WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and

cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.

Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.

ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,

die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann

hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um

professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist

durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.

TECHNISCHE DATEN

Spannweite 1620mm

Lange 1210mm

Elektroantrieb (siehe nächste Seite)

Verbrennerantrieb 7.5cc 2-T / 8.5cc 4-T

Fernsteuerung 6 Kanal / 6-7 Servos

DO-27

Designed for brushless electric motors (.46-.52 class glow conversion optional)

Entwickelt für Brushless Elektro Motoren (7,5 -8,5cc Glühzündermotor Einbau möglich)

Full the elevator out of the

horizontal stabilizer.

Cut away only

the film both side

When you are satisfied with the alignment,

use a pencil to trace around the top and

bottom of the stabilizer where it meets the

fuselage.

Cut away only

the covering

both side

BB’

B=B’

Aluminum wing joiner

Remove the horizontal stabilizer from the

fuselage. Using the sharp hobby knife,

carefully cut away the covering inside the

lines which were marked above.

* WARNING: When removing any covering

from the airframe, please ensure that you

secure the cut edge with CA or similar

cement. This will ensure the covering

remain tight.

Stabilizer

AA’

A=A’

Stabilizer

FUSELAGE

Again, Install the horizontal stabilizer into the

fuselage and adust the alignment as described

in steep 1C. Secure the horizontal stabilizer in

place using CA glue.

DORNIER DO-27 1-Horizontal stabilizer

Note: The slots for the control horn

installation are pre- cut at factory.

Control horn

...........2

Thin CA glue

Push the elevator and its hinges into the hinge slots in the trailing edge of the

horizontal stabilizer.

There should be a minimal hinge gap.

When satisfied with the and alignment, hinge the elevator to the horizontal stabilizer using CA glue.

Hinge STABILIZER

Apply thin CA to both

side of the hinge

Full the rudder out of the

vertical stabilizer.

3A 3B

WARNING! Securely glue together.

If coming off during flights, you lose control

of your airplane which leads to accidents !

Vergewissern Sie sich, sauber geklebt zu haben.

Andernfalls konnen Probleme mit der Flugeigenschaft

auftreten!

DORNIER DO-27 3-Vertical stabilizer

DORNIER DO-27 2-Horizontal stabilizer

When you are satisfied with the alignment,

use a pencil to trace around the right and

left of the stabilizer where it meets the

fuselage.

Cut away only

the covering

both side

Realign the vertical stabilizer, then glue

the vertical stabilizer into the fuselage,

using a generous amount of thin CA.

Thin CA glue

Hinge STABILIZER

Apply thin CA to both

side of the hinge

Push the rudder and its hinges into the hinge slots in the trailing edge of the

horizontal stabilizer. There should be a minimal hinge gap.

When satisfied with the and alignment, hinge the elevator to the horizontal stabilizer using CA glue.

4B 4C

WARNING! Securely glue together.

If coming off during flights, you lose control

of your airplane which leads to accidents !

Vergewissern Sie sich, sauber geklebt zu haben.

Andernfalls konnen Probleme mit der Flugeigenschaft

auftreten!

WARNING! Securely glue together.

If coming off during flights, you lose control

of your airplane which leads to accidents !

DORNIER DO-27 4-Vertical stabilizer

Note: The slots for the control horn

installation pre- cut at factory.

Control horn

...........2

3x12mm screw

.......................2

......................1

1.5mm

3x12mm screw

Collar

DORNIER DO-27 5-Rudder control horn

WARNING! Securely glue together.

If coming off during flights, you lose control

of your airplane which leads to accidents !

DORNIER DO-27 6-Tail wheel

2mm

FUSELAGE

..................2

3x12mm bolt

...........2

.........4

3X15mm hex bolt

Cut off the shadow area

......2

4X40mm screw

4mm nut

............................2

............................6

4mm washer

4mm nut

4x40mm screw

Aluminum landing gear

DORNIER DO-27 7- Main gear

Using a aluminum motor mounting plate as a template, mark

the plywood motor mounting plate where the four holes are

to be drilled (A).

Remove the aluminum motor mounting plate and drill a 3mm

hole through the plywood at each of the four marks marked (B).

Using a plywood motor mounting

plate as a template, mark the fire-

wall where the four holes are to

be drilled (C) .

Aluminum motor mounting plate

(included with electric motor set)

Push the four 5x35mm bolts through

the fire-wall as shown (E)

Reposition the plywood motor

mounting plate and secure

it in place with twelve 5xmm nuts and

washers (E).

Pull the magnetic battery hatch

out of the fuselage

! Align the mark on plywood

motor mounting with the center

mark on the fire-wall

Plywood motor

mounting

Remove the plywood motor

mounting plate and drill a 5mm

hole through the fire-wall at

each of the four marks marked

above (D).

5mm

DORNIER DO-27 8- Electric motor

Firewall

113mm

B’

B=B’

A=A’

A’ ! Engine thrust on balk head

is already adjust at factory

Attach the aluminum motor mounting

plate on to the motor and secure it in

place with four screws ( included with

motor set) (F).

TOP-VIEW / Draufsicht

SIDE-VIEW / Seitenansicht

Sturz und Zug beachten!

Sperrholztrager Platten zusammenkleben, wie gezeigt ausrichten

und Locher bohren.

Motor nach untenstehendem Schema einbauen.

Fur optimale Leistung empfehlen wir folgende Komponenten:

-Brushless-Motor PICHLER BOOST 60

-Brushless Regler PICHLER XQ-70

-LiPO Akku LEMONRC 3700-5S

-Luftschraube 12*6 - 13*8

For maximum performance, we recommended

the following:

-Brushless-Motor PICHLER BOOST 60

-Brushless Regler PICHLER XQ-70

-LiPO Battery LEMONRC 3700-5S

-Propeller 12*6 - 13*8

Throttle pushrod

FRONT

Elevator pushrod

Elevator servo

Rudder servo

(mini servo)

Throttle servo

BOARD - TOP VIEW

FUSELAGE - BOTTOM VIEW

The holes for the rudder servo

are Pre-cut at factory (left and

right side of the fuselage).

Cut away only the covering

Akku Kiettband

aus dem PICHLER

Sortiment

Best.Nr. C4739

Battery seat bell

Tipp

10A

10B 10C

DORNIER DO-27 9- Electric motor continued

DORNIER DO-27 10- Servo & linkage

1.5mm

1/16

2mm

L/R

BOTTOM - VIEW / Unteransicht

Cut here for standard servo

Aileron & flap

extension cord

Trial fit the control horn into

the slot.

If the parts will join, but with

a gaps, sand or trim the parts

a little at a time until the parts

meet exactly with no gaps.

Plastic control horn

Linkage Stopper set

.....................4

.................4

1.2mm O Alenk-Gestange

Aileron & flap pushrod

Do the same way with other wing half

Metal hook (x2)

Spring (x1)

L/R

Do the same way with other wing half

DORNIER DO-27 11- Cowling

2.5x10mm screw

..........4

DORNIER DO-27 12- Wing

DORNIER DO-27 13- Joining the wing

IMPORTANT: Please do not clean your model with pure alcohol, only use liquid soap with water or use glass cleaner

to clean on surface of your model to keep the colour not fade.

Note: Cut out the stickers and apply them in the

proper area. Do not peel the backing paper off all

at once.

Peel off one corner of the backing and cut off with

scissors.

Arrange sticker on model and when satisfied adhere

the corner without backing.

Carefully peel back the rest of the backing while at

the same time adhering the rest of the sticker.

Try not to make air bubbles, if there are some,

carefully puncture sticker (center of bubble) but not

model surface with the tip

of the knife or sharp pin and squeeze out the air.

At curves stretch sticker and apply a little heat so

that no ceases occur.

Cut off the excess that is produced.

DORNIER DO-27 14- Joining the wing

DORNIER DO-27 15- Decor

Inhaltsverzeichnis

Andere Nexa Spielzeug Handbücher

Nexa

Nexa NE-1 NAVY CUB Bedienungsanleitung

Nexa

Nexa BEECHCRAFT T-34C TURBO MENTOR MILITARY... Bedienungsanleitung

Nexa

Nexa Focke Wulf FW-190A Bedienungsanleitung

Nexa

Nexa MESSERSCHMITT Me-109 Bedienungsanleitung

Nexa

Nexa U.S NAVY DIVE BOMBER SBD-5 DAUNTLESS Bedienungsanleitung

Nexa

Nexa AGWAGON C188 Bedienungsanleitung

Nexa

Nexa CE-208 Bedienungsanleitung

Nexa

Nexa Dago red Unlimited Air Racer 4 Bedienungsanleitung

Nexa

Nexa Pilatus Porter PC-6 Bedienungsanleitung

Nexa

Nexa Tri-Pacer Piper PA-22 Bedienungsanleitung

Nexa

Nexa CURTISS P-40 Bedienungsanleitung

Nexa

Nexa MACCHI MC 205 Bedienungsanleitung

Nexa

Nexa YAK-9 Bedienungsanleitung

Nexa

Nexa MITSUBISHI A6M5 ZERO Bedienungsanleitung

Nexa

Nexa Royal Air Force Supermarine Spitfire Bedienungsanleitung

Nexa

Nexa P-39 Q/N AIRACOBRA Bedienungsanleitung

Nexa

Nexa P-38 Lightning Bedienungsanleitung

Nexa

Nexa Pilatus Porter PC-6 Bedienungsanleitung

Beliebte Spielzeug Handbücher anderer Marken

marklin

marklin 37321 Bedienungsanleitung

Canon

Canon PAPER CRAFT Bedienungsanleitung

GREAT PLANES

GREAT PLANES Pitts M-12S Bedienungsanleitung

NOCH

NOCH 14261 Bedienungsanleitung

Hausler

Hausler 450 SE V2 Bedienungsanleitung

Dynaflite

Dynaflite Daydream Bedienungsanleitung

Kenner

Kenner Batman 63651 Bedienungsanleitung

LEGO

LEGO 8527 Bedienungsanleitung

Multiplex

Multiplex EasyStar II Bedienungsanleitung

iKarus

iKarus ECO 8 Bedienungsanleitung

Walkera

Walkera 38 Bedienungsanleitung

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Bedienungsanleitung

MD MXION SWD Bedienungsanleitung

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Bedienungsanleitung

marklin

marklin 39671 Bedienungsanleitung

LEGO

LEGO TECHNIC 8735 Bedienungsanleitung

Mattel

Mattel HOTWHEELS DWL04 Bedienungsanleitung

REVELL

REVELL Bristol Beaufighter TF.X Bedienungsanleitung