NI SCXI-1160 Kurzanleitung

NOTE TO USERS

NI SCXI -1160/1161 Jumpers

The NI SCXI-1160/1161 has two jumpers that are dedicated for

communication between the NI SCXI-1160/1161 and the controller. On the

NI SCXI-1160, these jumpers are W1 and W5. On the NI SCXI-1161,

these jumpers are W1 and W2.

In addition, the NI SCXI-1160/1161 has three jumpers that indicate to the

module what type of controller is connected to its rear connector. On the

NI SCXI-1160, these jumpers are W2, W3, and W4. On the NI SCXI-1161,

these jumpers are W3, W4, and W5. You may need to change the jumpers

of this cabled module. For modules not cabled to a controller, the jumper

settings are irrelevant.

NI SCXI-1160

To control the NI SCXI-1160 with an E Series device, NI 4021, or

NI digital multimeter (DMM), set jumpers W2, W3, and W4 for

multifunction I/O (MIO) communication. Refer to Table 1 and Figure 1.

Table 1. NI SCXI-1160 Jumpers

Jumper Setting

W1 1-2, 2-3

W2 DIO (controller is digital I/O (DIO) device)

MIO (controller is E Series device, NI 4021, or National Instruments DMM)

W3 DIO (controller is DIO device)

MIO (controller is E Series device, NI 4021, or National Instruments DMM)

W4 DIO (controller is DIO device)

MIO (controller is E Series device, NI 4021, or National Instruments DMM)

W5 1-2, 2-3

Note:Factory settings of the NI SCXI-1160 jumpers are bold.

™

Ρ΅νιϋΠȂ඾ུࢊβȜΐ܄ȃ

NI SCXI-1160/1161 Jumpers 2 ni.com

Figure 1. NI SCXI-1160 Jumper Locations (Default)

NI SCXI-1161

To control the NI SCXI-1161 with an E Series device, NI 4021, or

National Instruments DMM, set jumpers W3, W4, and W5 for MIO

communication. Refer to Table 2 and Figure 2.

1W1

2W2

3W3

4W4

5W5

Table 2. NI SCXI-1161 Jumpers

Jumper Setting

W1 1-2, 2-3

W2 1-2, 2-3

W3 DIO (controller is DIO device)

MIO (controller is E Series device, NI 4021, or National Instruments DMM)

W4 DIO (controller is DIO device)

MIO (controller is E Series device, NI 4021, or National Instruments DMM)

W5 DIO (controller is DIO device)

MIO (controller is E Series device, NI 4021, or National Instruments DMM)

Note: Factory settings of the NI SCXI-1161 jumpers are bold.

NI SCXI-1160

1

2

3

4

5

©National Instruments Corporation 3 NI SCXI-1160/1161 Jumpers

Figure 2. NI SCXI-1161 Jumper Locations (Default)

1W1

2W2

3W3

4W4

5W5

NI SCXI-1161

1

2

3

4

5

National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation. Refer to the Terms of Use section on

ni.com/legal for more information about National Instruments trademarks. Other product and company names mentioned herein are

trademarks or trade names of their respective companies. For patents covering National Instruments products, refer to the appropriate location:

Help»Patents in your software, the patents.txt file on your CD, or ni.com/patents.

© 2004–2007 National Instruments Corporation. All rights reserved. 373831B Dec07

Dieses Handbuch passt für folgende Modelle

1

Inhaltsverzeichnis

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung