Nibe SAM 40 Benutzerhandbuch

Installer manual

LEK

SAM 40

Supply air module

IHB EN 1846-1

531368

LEK

Table of Contents

41 Important information

4Safety information

4General

62 Delivery and handling

6Transport

6Assembly

6Supplied components

6Removing the covers

3 The design of the supply air mod-

ule

8Pipe connections

8HVAC components

8Sensors etc.

8Electrical components

8Ventilation

8Miscellaneous

94 Pipe and ventilation connections

9General pipe connections

10Dimensions and pipe connections

10Heating medium side

13Installation alternative

15General ventilation connection

15Ventilation flow

15Adjusting ventilation

15Dimension and ventilation connections

165 Electrical connections

16General

16Connections

176 Commissioning and adjusting

17Preparations

17Filling and venting

18Start-up and inspection

197 Program settings

19Menu system

208 Disturbances in comfort

20Info-menu

20Troubleshooting

229 Accessories

2310 Technical data

23Dimensions and setting-out coordinates

24Technical specifications

25Electrical circuit diagram

26Item register

27Contact information

3Table of Contents |SAM 40

Safety information

This manual describes installation and service procedures

for implementation by specialists.

The manual must be left with the customer.

This appliance can be used by children

aged from 8 years and above and per-

sons with reduced physical, sensory or

mental capabilities or lack of experience

and knowledge if they have been given

supervision or instruction concerning use

of the appliance in a safe way and under-

stand the hazards involved. Children shall

not play with the appliance. Cleaning

and user maintenance shall not be made

by children without supervision.

Rights to make any design or technical

modifications are reserved.

©NIBE 2018.

NOTE

If the supply cable is damaged, only

NIBE, its service representative or

similar authorised person may re-

place it to prevent any danger and

damage.

Symbols

NOTE

This symbol indicates danger to person or ma-

chine .

Caution

This symbol indicates important information

about what you should observe when maintain-

ing your installation.

TIP

This symbol indicates tips on how to facilitate

using the product.

Marking

The CE mark is obligatory for most products sold

in the EU, regardless of where they are made.

Classification of enclosure of electro-technical

equipment.

IP21

Danger to person or machine.

Read the User Manual.

General

Software version

The heat pump must have software version 8432R2

(F370)/3585R2 (F750) or later. Visit www.nibeuplink.com

and click on the tab "Software" to download the latest

software to your installation or use the enclosed USB

memory.

Serial number

The serial number can be found at the bottom left inside

the front cover.

LEK

Serial number

LEK

Caution

You need the product's 14 digit serial number

for servicing and support.

Recovery

Leave the disposal of the packaging to the in-

staller who installed the product or to special

waste stations.

When disposing of the product, its constituent

materials and components, e.g. compressors,

fans, circulation pumps and circuit boards, must be dis-

posed of at a special waste station or dealer who

provides this type of service.

To access the separate components, refer to the section

that shows the construction of the product. No special

tools are required for access.

Improper disposal of the product by the user results in

administrative penalties in accordance with current legis-

lation.

SAM 40Chapter 1 | Important information4

1 Important information

Inspection of the installation

In addition, fill in the page for the installation data in the User Manual.

Current regulations require the supply air module to be inspected before it is put into service. The inspection must

be carried out by a suitably qualified person.

DateSignatureNotesDescription

✔

Ventilation (page 15)

Setting ventilation flow exhaust air

Setting ventilation flow supply air

Heating medium (page 10)

System flushed

Accessories bled

Check against output and pressure drop

diagrams

Connected according to outline diagram

Electricity (page 16)

Supply connected 230 V

Connected communication

5Chapter 1 | Important informationSAM 40

Transport

The supply air module must be transported and stored

dry.

Assembly

SAM 40 is mounted free-standing on brackets, alternat-

ively above a VPB 200 (for VPB 300/VPBS 300 installation

is carried out using brackets). Noise from the fan can be

transferred to the brackets.

■Install the brackets to an outside wall, ideally in a room

where noise does not matter, in order to eliminate

noise problems. If this is not possible, avoid placing it

against a wall behind a bedroom or other room where

noise may be a problem.

■Wherever the unit is located, walls to sound sensitive

rooms should be fitted with sound insulation.

■Route pipes so they are not fixed to an internal wall

that backs on to a bedroom or living room.

Installation area

Leave a free space of 800 mm in front of the supply air

module. All service on SAM 40 can be carried out from

the front.

800

NOTE

Ensure that there is sufficient space (300 mm)

above the supply air module for installing

ventilation hoses.

Supplied components

LEK

Vent hose

1 x

Support bushes

2 x

Removing the covers

Front cover

1. Remove the service cover by pulling it straight out.

LEK

SAM 40Chapter 2 | Delivery and handling6

2 Delivery and handling

LEK

S3 AA5-S2 AA5

AA5

AA5-S2

LEK

XL33 XL34QM20

PF1 HQ11

Svenskt produktblad

XL33 BT23

HQ11

XL34

AA100

QM20

PF 1

BT22

LEK

W6 W1

SF1

W101

SF1

W102

LEK

EP13 XL37 XL36

QN40

GQ3

Svenskt produktblad

GQ3EP13 XL36

XL37

BT69 BT68

QN40

7Chapter 3 | The design of the supply air moduleSAM 40

3 The design of the supply air module

Pipe connections

Ventilation connection supply airXL33

Ventilation connection outdoor airXL34

Connection, heating medium inXL36

Connection, heating medium outXL37

HVAC components

Supply air batteryEP13

Venting heating mediumQM20

Control valve heating mediumQN40

Sensors etc.

Temperature sensor, supply airBT22

Temperature sensor, outdoor airBT23

Temperature sensor, flowBT68

Temperature sensor, returnBT69

Electrical components

Accessory cardAA5

Dip switchAA5-S2

Joint board1

AA100

Switch, position 0 - 1, main switchSF1

Cord with connection plugW101

Communication cableW102

Ventilation

Supply air fanGQ3

Air filter supply airHQ11

Miscellaneous

Rating platePF1

1Not visible in the image

Designations in component locations according to

standard IEC 81346-1 and 81346-2.

SAM 40Chapter 3 | The design of the supply air module8

General pipe connections

Pipe installation must be carried out in accordance with

current norms and directives.

Compatible NIBE heat pumps

SAM 40 is installed together with a compatible exhaust

air heat pump from NIBE. You adjust the settings and

read off sensor values etc. for the supply air module in

the heat pump’s display.

Compatible products

■F370

■F750

Symbol key

MeaningSymbol

Control valve

Fan

System diagram

NOTE

External frost protection (outdoor air damper)

should be installed in the outdoor air duct, if

SAM 40 is installed in a cold climate.

-AZ2

SAM 40

For installation with F750, a buffer vessel (UKV) may be

required. See installation alternatives on page 14.

9Chapter 4 | Pipe and ventilation connectionsSAM 40

4 Pipe and ventilation connections

Dimensions and pipe

connections

295

320

210

Ø22

420

Heating medium side

Dimensioning the system

1. Work from the water temperature at DOT (DVOT).

2. Work from the current supply air flow.

3. Work from the desired supply air temperature, then

calculate the output that SAM 40 must give at DOT.

4. Determine the water flow across SAM 40 from the

correct output diagram.

NOTE

For supply temperatures that do not ap-

pear in any of the diagrams, an estimate

(linear interpolation) can be made.

5. Work from the projected pressure drop (at the pro-

jected flow) in the waterborne system that is parallel

with SAM 40.

6. Check in the pressure drop diagram that the working

point is inside the grey working range.

7. Check that the pump capacity from the heat pump

is sufficient for both the heating system and SAM

40.

SAM 40Chapter 4 | Pipe and ventilation connections10

Andere Handbücher für SAM 40

Inhaltsverzeichnis

Andere Nibe Steuereinheit Handbücher

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung