Nibe SAM 40 Benutzerhandbuch
Installer manual
LEK
SAM 40
Supply air module
IHB GB 1549-4
031934
LEK
LEK
Table of Contents
41 Important information
4Safety information
72 Delivery and handling
7Transport
7Assembly
7Removing the covers
8
3 The design of the supply air mod-
ule
104 Pipe and ventilation connections
10General pipe connections
10Symbol key
10Outline diagram
11Dimensions and pipe connections
11Mounting
12Heating medium side
16General ventilation connection
16Ventilation flow
16Adjusting ventilation
175 Electrical connections
17General
17Connections
186 Commissioning and adjusting
18Preparations
18Connecting to heating medium system
18Start-up and inspection
217 Disturbances in comfort
21Info menu
21Manage alarm
21Troubleshooting
238 Accessories
249 Technical data
24Dimensions and setting-out coordinates
25Technical specifications
26Energy labelling
27Electrical circuit diagram
28Index
3Table of Contents |SAM 40
Safety information
This manual describes installation and service proced-
ures for implementation by specialists.
This appliance can be used by children
aged from 8 years and above and per-
sons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning
use of the appliance in a safe way and
understand the hazards involved. Chil-
dren shall not play with the appliance.
Cleaning and user maintenance shall
not be made by children without super-
vision.
Rights to make any design or technical
modifications are reserved.
©NIBE 2015.
Symbols
NOTE
This symbol indicates danger to machine or
person.
Caution
This symbol indicates important information
about what you should observe when main-
taining your installation.
TIP
This symbol indicates tips on how to facilitate
using the product.
Marking
SAM 40 is CE marked and fulfils IP21.
The CE marking means that NIBE ensures that the
product meets all regulations that are placed on it
based on relevant EU directives. The CE mark is obligat-
ory for most products sold in the EU, regardless where
they are made.
IP21 means that objects with a diameter larger than
or equivalent to 12.5 mm cannot penetrate and cause
damage and that the product is protected against
vertically falling drops of water.
Serial number
Serial number
The serial number can be found at the bottom left in-
side the front cover.
LEK
Serial number
LEK
Caution
Always give the product's serial number (14
digits) when contacting your installer.
Recovery
Leave the disposal of the packaging to the in-
staller who installed the product or to special
waste stations.
When disposing of the product, the constitu-
ent materials and components, such as com-
pressors, fans, circulation pumps and circuit boards,
must be disposed of at a special waste station or at a
dealer who provides this type of service.
To access the separate components, refer to the section
that shows the construction of the product. No special
tools are required for access.
Improper disposal of the product by the user results in
administrative penalties in accordance with current
legislation.
Country specific information
Installer manual
This installer manual must be left with the customer.
SAM 40Chapter 1 | Important information4
1 Important information
Inspection of the installation
In addition, fill in the page for the installation data in the User Manual.
Current regulations require the supply air module to be inspected before it is put into service. The inspection must
be carried out by a suitably qualified person.
DateSignatureNotesDescription
✔
Ventilation (page 16)
Setting ventilation flow exhaust air
Setting ventilation flow supply air
Heating medium (page 12)
System flushed
Accessories bled
Check against output and pressure drop
diagrams
Connected according to outline diagram
Electricity (page 17)
Connections
Phase voltage
Supply connected 230 V
Connected communication
5Chapter 1 | Important informationSAM 40
Contact information
KNV Energietechnik GmbH, Gahberggasse 11, 4861 SchörflingAT
Tel: +43 (0)7662 8963-0 Fax: +43 (0)7662 8963-44 E-mail: mail@knv.at www.knv.at
NIBE Wärmetechnik c/o ait Schweiz AG, Industriepark, CH-6246 AltishofenCH
Druzstevni zavody Drazice s.r.o, Drazice 69, CZ - 294 71 Benatky nad JizerouCZ
NIBE Systemtechnik GmbH, Am Reiherpfahl 3, 29223 CelleDE
Vølund Varmeteknik A/S, Member of the Nibe Group, Brogårdsvej 7, 6920 VidebækDK
NIBE Energy Systems OY, Juurakkotie 3, 01510 VantaaFI
NIBE Energy Systems France Sarl, Zone industrielle RD 28, Rue du Pou du Ciel, 01600 ReyrieuxFR
NIBE Energy Systems Ltd, 3C Broom Business Park, Bridge Way, Chesterfield S41 9QGGB
NIBE Energietechniek B.V., Postbus 634, NL 4900 AP OosterhoutNL
ABK AS, Brobekkveien 80, 0582 Oslo, Postadresse: Postboks 64 Vollebekk, 0516 OsloNO
NIBE-BIAWAR Sp. z o. o. Aleja Jana Pawła II 57, 15-703 BIAŁYSTOKPL
Tel: 085 662 84 90 Fax: 085 662 84 14 E-mail: sekretariat@biawar.com.pl www.biawar.com.pl
© "EVAN" 17, per. Boynovskiy, Nizhny NovgorodRU
NIBE AB Sweden, Box 14, Hannabadsvägen 5, SE-285 21 MarkarydSE
For countries not mention in this list, please contact Nibe Sweden or check www.nibe.eu for more information.
SAM 40Chapter 1 | Important information6
Transport
The supply air module must be transported and stored
dry.
Assembly
SAM 40 is mounted free standing on brackets, altern-
atively above a VPB 200 (For VPB 300/VPBS 300 install-
ation is with the help of brackets). Noise from the fan
can be transferred to the brackets.
■Install the brackets to an outside wall, ideally in a
room where noise does not matter, in order to elim-
inate noise problems. If this is not possible, avoid
placing it against a wall behind a bedroom or other
room where noise may be a problem.
■Wherever the unit is located, walls to sound sensitive
rooms should be fitted with sound insulation.
■Route pipes so they are not fixed to an internal wall
that backs on to a bedroom or living room.
Installation area
Leave a free space of 500 mm in front of the supply air
module. All service on SAM 40 can be carried out from
the front.
800
NOTE
Ensure that there is sufficient space (300 mm)
above the supply air module for installing
ventilation hoses.
Removing the covers
Front cover
1. Remove the service cover by pulling it straight out.
LEK
7Chapter 2 | Delivery and handlingSAM 40
2 Delivery and handling
LEK
LEK
S3 AA5-S2 AA5
AA5
AA5-S2
LEK
LEK
XL33 XL34QM20
PF1 HQ11
Svenskt produktblad
XL33 BT23
HQ11
XL34
AA100
QM20
PF 1
BT22
LEK
LEK
W6 W1
SF1
W101
SF1
W102
LEK
LEK
EP13 XL37 XL36
QN40
GQ3
Svenskt produktblad
GQ3EP13 XL36
XL37
BT69 BT68
QN40
SAM 40Chapter 3 | The design of the supply air module8
3 The design of the supply air module
Pipe connections
Ventilation connection supply airXL33
Ventilation connection outdoor airXL34
Connection, heating medium inXL36
Connection, heating medium out 1
XL37
HVAC components
Supply air batteryEP13
Venting heating mediumQM20
Control valve heating mediumQN40
Sensors etc.
Temperature sensor, supply airBT22
Temperature sensor, outdoor airBT23
Temperature sensor, flowBT68
Temperature sensor, return1
BT69
Electrical components
Accessory cardAA5
AA5-S2 Dip switch
Joint cardAA100
Switch, position 0 - 1, main switchSF1
Cord with connection plugW101
Control cableW102
Ventilation
Supply air fanGQ3
Air filter supply airHQ11
Miscellaneous
Rating platePF1
1Not visible in the image
Designations in component locations according to
standard IEC 81346-1 and 81346-2.
9Chapter 3 | The design of the supply air moduleSAM 40
General pipe connections
Pipe installation must be carried out in accordance with
current norms and directives.
Symbol key
MeaningSymbol
Control valve
Shunt / shuttle valve
Temperature sensor
Expansion vessel
Circulation pump
Fan
Compressor
Heat exchanger
Outline diagram
-EB100 -AZ2
-CP1
Caution
If the total circulating volume in the climate
system (excluding the heat pump volume) falls
below 40 litres, extra system volume is connec-
ted, for example volume vessel UKV (CP1) ac-
cording to the outline diagram above.
NOTE
If several climate systems (ECS 40/ECS 41) are
present, SAM 40 must be connected in parallel
with climate system 1. A circulation pump must
be used to ensure the flow over SAM 40.
SAM 40Chapter 4 | Pipe and ventilation connections10
4 Pipe and ventilation connections
Andere Handbücher für SAM 40
3
Inhaltsverzeichnis
Andere Nibe Steuereinheit Handbücher
Nibe
Nibe VVM 320 Bedienungsanleitung
Nibe
Nibe VVM 325 Benutzerhandbuch
Nibe
Nibe FLM Benutzerhandbuch
Nibe
Nibe SMO 20 Benutzerhandbuch
Nibe
Nibe SAM 41 Benutzerhandbuch
Nibe
Nibe VVM S320 Benutzerhandbuch
Nibe
Nibe BIAWAR ME 0015 Bedienungsanleitung
Nibe
Nibe SMO 20 UK Benutzerhandbuch
Nibe
Nibe SMO 40 Benutzerhandbuch
Nibe
Nibe POOL 40 Benutzerhandbuch
Nibe
Nibe PKM 05 Bedienungsanleitung
Nibe
Nibe RMU S40 Benutzerhandbuch
Nibe
Nibe CMO 11 Original Betriebsanleitung
Nibe
Nibe VCC11 Benutzerhandbuch
Nibe
Nibe SMO 40 Benutzerhandbuch
Nibe
Nibe DEH 310 Benutzerhandbuch
Nibe
Nibe VVM 225 UK 1x230V Bedienungsanleitung
Nibe
Nibe VVM 500 Bedienungsanleitung
Nibe
Nibe RCU 10 Bedienungsanleitung
Nibe
Nibe SAM 40 Benutzerhandbuch
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
