Nibe SMO 05 Benutzerhandbuch

Installer manual

LEK

SMO 05

Accessories

IHB GB 1339-3

431197

4XLFN JXLGH

1DYLJDWLRQ 2N EXWWRQ FRQILUPVHOHFW

%DFN EXWWRQ EDFNXQGRH[LW

8SGRZQ EXWWRQV

PRYHLQFUHDVHUHGXFH

A detailed explanation of the button functions can be found on page 18.

How to scroll through menus and make different settings is described on page 19.

6HW WKH LQGRRU FOLPDWH

LQGRRU FOLPDWH

KRW ZDWHU

LQIR

P\ V\VWHP ;

The mode for setting the indoor temperature is reached, when in the start mode in the main menu, by pressing the

OK button twice. Read more about the settings on page 20.

,QFUHDVH KRW ZDWHU YROXPH

7(0325$5< /8; 

RII

;

;

To temporarily increase the amount of hot water (if a hot water heater is installed to your SMO 05), first push the

down button once to mark menu 2 (water droplet) and then press the OK button twice. Read more about the settings

on page 24.

In event of disturbances in comfort

If a disturbance in comfort of any type occurs there are some measures that can be taken before you need to contact

your installer. See page 30 for instructions.

Table of Contents

1 Important information 2

Safety information 2

2 Delivery and handling 5

Mounting 5

Supplied components 6

Removing the covers 6

3 The Control Module Design 7

Room unit 7

Unit box 7

4 Pipe connections 8

General 8

Docking alternatives 8

5 Electrical connections 11

General 11

Connections 11

Settings 16

Connecting accessories 16

6 Commissioning and adjusting 17

Preparations 17

Commissioning with NIBE air/water heat

pump 17

Commissioning without NIBE air/water heat

pump 17

Check the reversing valve 17

7 Control - Introduction 18

Room unit 18

Menu system 18

8 Control - Menus 20

Menu 1 - INDOOR CLIMATE 20

Menu 2 - HOT WATER 24

Menu 3 - INFO 25

Menu 4 MY SYSTEM 26

Menu 5 - SERVICE 28

9 Disturbances in comfort 30

Manage alarm 30

Troubleshooting 30

Add. heat only 31

10 Accessories 32

11 Technical data 33

Dimensions and setting-out coordinates 33

Technical specifications 35

Electrical circuit diagram 36

Item register 37

1Table of Contents |SMO 05

Safety information

This manual describes installation and service procedures

for implementation by specialists.

This appliance is not intended for use by persons (includ-

ing children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concern-

ing use of the appliance by a person responsible for their

safety.

Children should be supervised to ensure that they do not

play with the appliance.

Rights to make any design or technical modifications are

reserved.

©NIBE 2012.

Symbols

NOTE

This symbol indicates danger to machine or

person.

Caution

This symbol indicates important information

about what you should observe when maintain-

ing your installation.

TIP

This symbol indicates tips on how to facilitate

using the product.

Marking

This accessory is CE marked and fulfils IP20 (room unit)

and IP21 (unit box).

The CE marking means that NIBE ensures that the product

meets all regulations that are placed on it based on relev-

ant EU directives. The CE mark is obligatory for most

products sold in the EU, regardless where they are made.

IP20 means that the product can be touched by hand,

that objects with a diameter larger than or equivalent

to12.5 mm cannot penetrate and cause damage.

Serial number

The serial number can be found on one long side of the

cover on the unit box.

Install the cover on the unit box so that the serial number

is visible.

LEK

6HULDO QXPEHU

Caution

Always give the product's serial number when

reporting a fault.

Country specific information

Installer manual

This installer manual must be left with the customer.

SMO 05Chapter 1 | Important information2

1 Important information

Inspection of the installation

Current regulations require the heating installation to be inspected before it is commissioned. The inspection must be

carried out by a suitably qualified person. Fill in the page for information about installation data in the User manual.

DateSignatureNotesDescription

✔

Communication, heat pump

Electricity (page 11)

Supply connected 230 V

Outside sensor

Room sensor

Hot water sensor

Room unit

Bridge at installation of room unit

Dipswitch

Miscellaneous

Checking additional heater

Checking the function of the reversing valve

3Chapter 1 | Important informationSMO 05

..........................................................................................................................................................................................................................................................................................................................................................................................

Contact information

KNV Energietechnik GmbH, Gahberggasse 11, 4861 SchörflingAT

Tel: +43 (0)7662 8963-0 Fax: +43 (0)7662 8963-44 E-mail: [email protected] www.knv.at

NIBE Wärmetechnik AG, Winterthurerstrasse 710, CH-8247 FlurlingenCH

Tel: (52) 647 00 30 Fax: (52) 647 00 31 E-mail: [email protected] www.nibe.ch

Druzstevni zavody Drazice s.r.o, Drazice 69, CZ - 294 71 Benatky nad JizerouCZ

Tel: +420 326 373 801 Fax: +420 326 373 803 E-mail: [email protected] www.nibe.cz

NIBE Systemtechnik GmbH, Am Reiherpfahl 3, 29223 CelleDE

Tel: 05141/7546-0 Fax: 05141/7546-99 E-mail: [email protected] www.nibe.de

Vølund Varmeteknik A/S, Member of the Nibe Group, Brogårdsvej 7, 6920 VidebækDK

Tel: 97 17 20 33 Fax: 97 17 29 33 E-mail: [email protected] www.volundvt.dk

NIBE Energy Systems OY, Juurakkotie 3, 01510 VantaaFI

Puh: 09-274 697 0 Fax: 09-274 697 40 E-mail: [email protected] www.nibe.fi

AIT France, 10 rue des Moines, 67000 HaguenauFR

Tel : 03 88 06 24 10 Fax : 03 88 06 90 15 E-mail: [email protected] www.nibe.fr

NIBE Energy Systems Ltd, 3C Broom Business Park, Bridge Way, Chesterfield S41 9QGGB

Tel: 0845 095 1200 Fax: 0845 095 1201 E-mail: [email protected] www.nibe.co.uk

NIBE Energietechniek B.V., Postbus 2, NL-4797 ZG WILLEMSTAD (NB)NL

Tel: 0168 477722 Fax: 0168 476998 E-mail: [email protected] www.nibenl.nl

ABK AS, Brobekkveien 80, 0582 Oslo, Postadresse: Postboks 64 Vollebekk, 0516 OsloNO

Tel. sentralbord: +47 23 17 05 20 E-mail: [email protected] www.nibeenergysystems.no

NIBE-BIAWAR Sp. z o. o. Aleja Jana Pawła II 57, 15-703 BIAŁYSTOKPL

Tel: 085 662 84 90 Fax: 085 662 84 14 E-mail: [email protected] www.biawar.com.pl

Tel./fax +7 831 419 57 06 E-mail: [email protected] www.nibe-evan.ru

NIBE AB Sweden, Box 14, Hannabadsvägen 5, SE-285 21 MarkarydSE

Tel: +46-(0)433-73 000 Fax: +46-(0)433-73 190 E-mail: [email protected] www.nibe.se

For countries not mention in this list, please contact Nibe

Sweden or check www.nibe.eu for more information.

SMO 05Chapter 1 | Important information4

Mounting

NOTE

For wall mounting, use the mounting adapted

for the base.

Unit box

100

235

250

160

175

Room unit

Mounting

SMO 05 cannot be installed directly against a wall be-

cause the connection terminal protrudes from the reverse.

Install SMO 05 either in a spare apparatus box or on the

plastic spacer supplied.

If you want to use the room temperature sensor in SMO

05 the position of the room unit is important. See page

13.

LEK

Open SMO 05 by inserting a screwdriver in one of

the 4 mm wide gaps in the edge. Press the screw-

driver straight in to open the clips. Repeat for the

other three clips.

LEK

Without plastic spacer: Place the rear panel in front

of the apparatus box and screw to the wall.

With plastic spacer: Screw the plastic spacer into the

wall. Then screw the the rear panel into the plastic

spacer with the two screws supplied.

LEK

Connect the room unit, see page 12.

LEK

Angle the front panel approx. 30 ° and secure the

two clips on one side. Then close the unit and secure

the two clips on the other side.

For dimensions and setting-out coordinates see page 34.

5Chapter 2 | Delivery and handlingSMO 05

2 Delivery and handling

Supplied components

LEK

Plastic spacer

frame

Room unitOutside sensor

LEK

Room sensorTemperature

sensor

Unit box

LEK

Insulation tapeCable tiesAluminium tape

LEK

Time relay

Removing the covers

Unit box

LEK

Remove the four screws in their respective corners and

lift the cover.

The outdoor temperature sensor/Room

temperature sensor

LEK

SMO 05Chapter 2 | Delivery and handling6

Room unit

Front

Rear side

+12V GND B A

-

Electrical components

Room unitAA 25

Terminal block, communication connectionJ3

Designations in component locations according to

standard IEC 81346-1 and 81346-2.

Unit box

LEK

AA5-X4

AA5-S2

AA5-X2 AA5-X9 X1

FA1

AA5-F1AA5

Electrical components

Miniature circuit-breaker. 10AFA1

Terminal block, power supplyX1

Accessory cardAA5

Terminal block, sensors and external

blocking

AA5-X2

Terminal block, communicationAA5-X4

Terminal block, circulation pump, mixing

valve and auxiliary relay

AA5-X9

DIP switchAA5-S2

Fine wire fuse, T4AH250VAA5-F1

Designations in component locations according to

standard IEC 81346-1 and 81346-2.

7Chapter 3 | The Control Module DesignSMO 05

3 The Control Module Design

General

Pipe installation must be carried out in accordance with

current norms and directives. See manual for NIBE

F2015/F2025/F2016/F2026/F2300 for installation of the

heat pump.

Symbol key

MeaningSymbol

Shut-off valve

Non-return valve

Shunt / shuttle valve

Safety valve

Trim valve

Temperature sensor

Pressure gauge

Circulation pump

Particle filter

Temperature sensor installation on pipe

Install the temperature sensors with cable ties (secure the

first cable tie to the pipe on the centre of the sensor and

the second about 5 cm after the sensor) and aluminium

tape. Then insulate with supplied insulation tape.

NOTE

Sensor and communication cables must not be

placed near power cables.

Docking alternatives

SMO 05 can be connected in several different ways, some

of which are shown below.

Further option information is available at www.nibe.eu

and in the respective assembly instructions for the ac-

cessories used. See page 32 for a list of the accessories

that can be used with SMO 05.

NOTE

This is the outline diagram. Actual installations

must be planned according to applicable stand-

ards.

Explanation

SMO 05AA25

Display unitAA4

Outside sensorBT1

Hot water sensor, ChargingBT6

Hot water sensor, Top (VPB)BT7

Flow sensor, ExternalBT25

Room sensorBT50

Time relayKF1

Heat pump (F2026/F2300)EB100

Charge pumpGP12

Particle filterHQ1

Miscel-

laneous

Immersion heaterEB1

Immersion heaterEB20

Expansion vessel closed, Hot waterCM4

Accumulator tankCP1

Accumulator tank with hot water heating

(VPA/VPAS/VPB)

CP10

Buffer vessel (UKV)CP11

Safety valve, Heating mediumFL2

Safety valve, Heat pumpFL10

Circulation pump, Heating mediumGP10

Auxiliary relay/ContactorKA10

Auxiliary relay/ContactorKA11

Drain valve, Heating mediumQM1

Shut-off valve, Heating medium, FlowQM31

Shut off valve, Heating medium, ReturnQM32

Shut-off valveQM40

Reversing valve, Hot water/Heating mediumQN10

Overflow valveQN26

Control valveQN50

Control valveQN51

Non-return valveRM10

Designations according to standards 81346-1 and 81346-

SMO 05Chapter 4 | Pipe connections8

4 Pipe connections

Andere Handbücher für SMO 05

Inhaltsverzeichnis

Andere Nibe Steuereinheit Handbücher

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung