Nilfisk-Advance GB 1133 Bedienungsanleitung

Instruction manual

GB 1133

Categories of application: U, S, C, B1, EOB, K1

ATTENTION

Keep these instructions for future reference!

1 Contents

Paragraph Page

1 Contents 2

2 Scope of the instruction manual 3

3 Tests 4

4 Categories of application 5

5 Technical specifications 6

6 General notice on safety 7

7 Filter and emptying systems 8

8 Initial operation 9

9 Adjusting the automatic gear change of the minimum airflow 10,11,12

10 Monitoring the airflow 13

11 Cleaning the filter 14

12 Emptying the container 15

13 Disposal of collected dust 16,17

14 Pre-separator 18

15 Notice on K1 vacuum cleaners used for removing asbestos 19

16 Service 20

2 Scope of the instruction manual

This instruction manual is valid for the the following machine types:

GB 1133 – U(L)

GB 1133 – C(M,H)

GB 1133 – S(M) - B1

GB 1133 – C(M,H) - B1

GB 1133 – C(M,H) - EOB/IS

GB 1133 - K1(H)

Meaning of the type name

GB 1033 - series

C(M,H) - category of application (dust class)

EOB - machine type

The machine type “industrial vacuum cleaner (IS)“ is left out. The machine type of

cleaners that have passed the additional “Dust Explosion Protection Test“ is “B1“.

3 Tests

All Nilfisk-Advance systems are tested in order to comply with the requirements of

system safety regulations. They have fulfilled the technical safety demands according

to the following special regulations:

- Technical Dust Test

- Mechanical and Electrical Test

- Noise Technology Test

DIN EN ISO 3744

- Additional Dust Explosion Protection Test

4 Categories of application

This Nilfisk machine is suitable for removing dusts of the following categories of

application:

“U“ suitable for removing hazardous, dry, not inflammable dusts whose MAK*

limiting value is greater than 1 mg/cm³ (comparable to the new dust class “L“

- light hazard - defined by EN 60335-2-69).

“S“ suitable for removing hazardous, dry, not inflammable dusts whose MAK

limiting value is greater than 0.1 mg/cm³ (comparable to the new dust class

“M“ - medium hazard - defined by EN 60335-2-69).

“C“ suitable for removing hazardous, dry, not inflammable dusts with all MAK

limiting values (comparable to the new dust class “M“) as well as dry, not

inflammable dusts of carcinogenic substances (comparable to the new dust

class “H“ – high hazard – defined by EN 60335-2-69). The cleaned air is fed

back to the workplace atmosphere.

“K1“ suitable for removing hazardous, dry, not inflammable dusts with all MAK

limiting values as well as dry, not inflammable dusts of carcinogenic

substances. The cleaned air is fed back to the workplace atmosphere

(comparable to the new dust class “H“).

*maximale Arbeitsplatz-Konzentration, maximal workplace concentration

Explanation

Since May 1998, Europe has a common norm. Dust removing systems are from now

on divided into three dust classes L, M and H. Older test certificates remain valid until

December 31st, 2002. “Category of application“ is a synonym for “dust class“.

5 Technical specifications

Voltage 400 V

Rated power 13,000 W

Vacuum 320 mbar

Connection Ø 70/100 mm

Airflow 750/930 m³/h

Filter area Main filter (U,S,C) 52,000 cm²

Prefilter (K1) 52,000 cm²

Main filter (K1) 60,000 cm²

Minimum airflow 300/580 m³/h-1

Protection class IP 54

Insulation class F

Noise emission

Sound pressure level measuring as described in DIN EN ISO 3744.

According to the machine guideline Appendix 1, point 1.75 f, the highest sound

pressure level is measured at 1 m distance from the machine at a height of 1.6 m.

The highest value is reached on the right side (view down on the inlet):

77 dB(A).

6 General notice on safety

Only original Nilfisk spare parts may be used.

The machine may only be operated by instructed and authorised individuals.

Liquids, aggressive gases, flammable materials or smouldering particles should not

be removed.

The machine may only be used for cleaning dry surfaces and is not suitable for

outdoor use.

The power cord should not be damaged by being driven over, squeezed, pulled tight

or around sharp corners. Keep the power cord away from heated surfaces.

The power cord should be checked at regular intervals for signs of damage or

ageing.

Do not use the machine when the power cord is not in perfect condition.

Only original Nilfisk-Advance spare parts should be used when replacing the power

cord.

When the mains plug is replaced, splash-proof protection and mechanical safety

must be assured.

The replacement of the power cord or the mains plug should be carried out by a

competent person.

After use, before cleaning or any maintenance or adjustment work the mains plug

must be unplugged.

Before connecting the cable, the dust-producing system has to be shut down.

MAINTENANCE

Regular maintenance test: check the bounce separator for damage, the integrity of

the system, the filter and the functioning of the control system. Nilfisk-Advance offers

maintenance contracts which guarantee constant performance and value

preservation of the machines and their technical safety functions by regular check-

ups.

7 Filters and emptying systems

The installed main and exhaust filters are approved by the German Trade

Association Institute for Safety at the Workplace (BIA). The transmission factors are

lower than the limiting values required by relating regulations.

The installed filters normally have a long service life. Exchange of filters should only

be carried out by Nilfisk-Advance Service.

Without the appropriate emptying system, the machine does not match the

requirements specified by relating regulations. In this case, danger to health

cannot be excluded.

Article numbers for filters and emptying systems

Category of application Main filter Disposal system

(dust class) Type A Type B

U (L) 040053

S (M) 040053 027641

C (M, H) 040053 030343 031101

K1 (H) (prefilter) 040053 4 x 02170000 030343 031101

Two different disposal systems are in use:

Type A: Dust bag system

Type B: Disposable container

8 Initial operation

Please read these notes of safety before initial operating.

The application scope of the machine is marked on the rating-plate.

Industrial vacuum cleaners are exclusively designed for removing settled dusts.

Extractors are designed for removing dust at that very place where it is produced.

Having removed the system from packaging, check it for completeness and

transportation damage. In case of damage or missing parts please contact Nilfisk-

Advance immediately. Before connecting the vacuum cleaner to the mains supply,

check that the voltage of the machine specified on the rating-plate corresponds with

the mains voltage.

Switch the motor on to control its direction of rotation.

When it is wrong, a red lamp at the switch housing flashes up.

Extractors: an arrow on the motor housing shows the right direction of rotation.

Working for a long time with the wrong direction of rotation heatens the

vacuum cleaner’s surface up to over 80°C.

When the direction of rotation is wrong two phases in the mains supply (not within the

machine) need to be exchanged. All electrical sockets of the workplace should have

the same phase sequence in order to operate the system in all areas of the

workplace.

Systems with antistatic design (B1)

These machines are not suitable for removing explosive materials, dusts with an

extremely low minimum ignition energy of less than 1 mJ and inflammable liquids.

Do not use others than conductible original Nilfisk-Advance accessories.

Use couplers that only allow connecting and disconnecting the system in voltage-free

condition.

Antistatic systems must be equipped with a protective circuit breaker or a blowout

fuse 16 A (delayed-action fuse).

The use of coupling devices and adapters is not allowed.

The system is ready for use when all equipment has been connected.

9 Adjusting the automatic gear change of the minimum airflow

Use the performance profile to adjust the cutoff point for the minimum

airflow of extractors. First of all, find out the minimal airflow that ensures

a good operation of the dust-producing system. Mark this value on the x-

axis, then draw a vertical line from here to the curve. Now draw a line

parallel to the x-axis from the point of intersection to the y-axis. This

value describes the vacuum that has to be adjusted at the vacuum

switch when the minimal airflow is no longer sufficient.

When adjusting the vacuum, you have to connect an appropriate

measuring device parallel to the vacuum switch. Throttle the airflow at

the suction inlet until the required value is reached. Now calibrate the

cutoff point by the adjusting screw of the vacuum switch.

When the minimal airflow falls short, the following happens after a few

seconds:

- the red warning light flashes up.

- the floating contact in the switch housing switches. This contact (6 A at

voltage of 230 V, AC11) manages the connection of the control circuit

the dust-producing system to the extractor or to control an external

optical or acoustical signal.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Nilfisk-Advance Staubsauger Handbücher

Nilfisk-Advance

Nilfisk-Advance GD 930 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance GM 80 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance UZ 964 Ergoclean Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance CFM WSS 100 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Buddy II Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance 3156 L Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance ATTIX 115-01 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance APC 328 Betriebsanleitung

Nilfisk-Advance

Nilfisk-Advance IVB 3-H Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance IQ 215 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance VHW320 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Viper Shovelnose SN18WD-U Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance VHC200 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Coupe Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance CTS22 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Smart Series Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance CFM 3707/10 Handbuch

Nilfisk-Advance

Nilfisk-Advance BACKUUM Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance GD 930 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SB Station Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW 650 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance One ECO Basic HB38 Nozzle Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Handy Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance ATTIX 791-2M/B1 Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch