Nordson UltimusPlus Bedienungsanleitung

UltimusPlus Dispenser Network Connection

Instructions

Introduction

This document provides procedures for connecting the UltimusPlus™ﬂuid dispenser to a network and then sending

commands to the dispenser, including commands to remotely switch dispense programs.

Connecting the Dispenser to a Computer

1. Switch ON the dispenser power.

2. Using standard Ethernet cables and an Ethernet switch, connect a personal computer with a static IP address to the

Ethernet port on the back of the UltimusPlus dispenser.

3. To set up your computer with the correct IP settings, continue to “Setting the IP Address of a Computer” on page 2.

Power ON

Ethernet

port

Ethernet cable

Ethernet

switch

Making the Ethernet connection between the

UltimusPlus dispenser and a computer

Ethernet cable

UltimusPlus Dispenser Network Connection

2www.nordsonefd.com [email protected] 800-556-3484 Sales and service of Nordson EFD dispensing systems are available worldwide.

Setting the IP Address of a Computer

Each computer in a networked system must have a unique IP address. Follow this procedure to change the IP address of a

computer.

NOTE: To change the IP address of the dispenser: Press Settings > Ethernet, enter the desired IP address, then press

Activate & Reboot.

1. On your computer, navigate to the “Network and Sharing Center.”

2. Click “Change Adapter Settings.”

Windows®7 Windows 10

3. Select “Local Area Connection” (Windows 7) or “Ethernet” (Windows 10).

Windows 7 Windows 10

4. Double-click (Windows 7) or right-click (Windows 10) to select “Properties.”

Windows 7 Windows 10

3www.nordsonefd.com [email protected] 800-556-3484 Sales and service of Nordson EFD dispensing systems are available worldwide.

UltimusPlus Dispenser Network Connection

Setting the IP Address of a Computer (continued)

5. Double-click “Internet Protocol Version 4 (TCP/IPv4).”

Windows 7 Windows 10

6. Click “Use the following IP address” and then enter the desired IP address.

NOTE: The digit range for each ﬁeld is 1–255.

7. Click OK > OK to save the new IP address.

Windows 7 Windows 10

8. Click OK in the Local Area Connection properties window (Windows 7) or the Ethernet properties window (Windows 10).

9. Depending on the networking tool you will be using, continue to one of the following sections to set up the computer to

send commands to the dispenser:

• “Using Tera Term to Communicate with the Dispenser” on page 4

• “Using PuTTY to Communicate with the Dispenser” on page 5

UltimusPlus Dispenser Network Connection

4www.nordsonefd.com [email protected] 800-556-3484 Sales and service of Nordson EFD dispensing systems are available worldwide.

Using Tera Term to Communicate with the Dispenser

1. Once the computer is connected to the UltimusPlus dispenser, open a command prompt (or a terminal) and ping the

IPaddress of the UltimusPlus dispenser. The default IP address of the dispenser is 192.168.10.40.

If the ping is successful, continue with the next steps to create a TCP connection to port 9000 of the dispenser. This

section provides instructions for using the Tera Term networking tool.

2. Open Tera Term and begin with the New Connection screen (shown below).

3. Select TCP/IP and, next for Host, enter the IP address of the UltimusPlus dispenser (192.168.10.40).

4. Click Setup > Terminal.

5. Select Local echo and Auto switch [VT<->TEK].

• If the error shown below appears, you are not connected to the dispenser and there is a network issue. Contact your

network administrator for assistance.

• If the command window shown below appears, then the TCP/IP connection is created and you can send commands

to the UltimusPlus dispenser. Refer to “UltimusPlus Dispenser Remote Commands” on page 6 for the command

list.

5www.nordsonefd.com [email protected] 800-556-3484 Sales and service of Nordson EFD dispensing systems are available worldwide.

UltimusPlus Dispenser Network Connection

Using PuTTY to Communicate with the Dispenser

1. Once the computer is connected to the UltimusPlus dispenser, open a command prompt (or a terminal) and ping the

IPaddress of the UltimusPlus dispenser. The default IP address of the dispenser is 192.168.10.40.

If the ping is successful, continue with the next steps to create a TCP connection to port 9000 of the dispenser. This

section provides instructions for using the PuTTY networking tool.

2. Open PuTTY and begin with the PuTTY Conﬁguration screen (shown below).

3. Ensure that the Host Name shows IP address (192.168.10.40) and Port (9000) of the UltimusPlus dispenser.

4. Click Open.

• If the error shown below appears, you are not on the same network or have entered the wrong IP address. Contact

your network administrator for assistance.

• If the command window shown below appears, then the TCP/IP connection is created.

Now you can send commands to the UltimusPlus dispenser. For each command you enter, PuTTY responds with

the same command, as shown below. Refer to “UltimusPlus Dispenser Remote Commands” on page 6 for the

command list.

UltimusPlus Dispenser Network Connection

For Nordson EFD sales and service in over

40 countries, contact Nordson EFD or go to

www.nordsonefd.com.

Global

800-556-3484; +1-401-431-7000

[email protected]

Europe

00800 7001 7001

[email protected]

Asia

China: +86 (21) 3866 9006; [email protected]

India: +91 80 4021 3600; [email protected]

Japan: +81 03 5762 2760; [email protected]

Korea: +82-31-736-8321; [email protected]

SEAsia: +65 6796 9522; [email protected]

UltimusPlus Dispenser Remote Commands

Command Response Result

Program1_0 Program1_0 Unit switches to program 1

Program2_0 Program2_0 Unit switches to program 2

Program3_0 Program3_0 Unit switches to program 3

Program4_0 Program4_0 Unit switches to program 4

Program5_0 Program5_0 Unit switches to program 5

Program6_0 Program6_0 Unit switches to program 6

Program7_0 Program7_0 Unit switches to program 7

Program8_0 Program8_0 Unit switches to program 8

Program9_0 Program9_0 Unit switches to program 9

Program10_0 Program10_0 Unit switches to program 10

Program11_0 Program11_0 Unit switches to program 11

Program12_0 Program12_0 Unit switches to program 12

Program13_0 Program13_0 Unit switches to program 13

Program14_0 Program14_0 Unit switches to program 14

Program15_0 Program15_0 Unit switches to program 15

Program16_0 Program16_0 Unit switches to program 16

DispenseTrigger_0 TriggeringDispense_0 If in timed mode, unit triggers a dispense

Andere Nordson Spender Handbücher

Nordson

Nordson Pro-Meter S-Series Referenzhandbuch

Nordson

Nordson UltimusPlus Series Bedienungsanleitung

Nordson

Nordson FoamMelt 200 Bedienungsanleitung

Nordson

Nordson Spectrum II Referenzhandbuch

Nordson

Nordson Asymtek X-1000 Series Einrichtungshandbuch

Nordson

Nordson Asymtek Spectrum Series Gebrauchsanweisung

Nordson

Nordson Ultimus V Bedienungsanleitung

Nordson

Nordson ASYMTEK Handbuch

Nordson

Nordson Rhino VE Standard Stücklistenhandbuch

Nordson

Nordson freedom Bedienungsanleitung

Nordson

Nordson PRO series Bedienungsanleitung

Nordson

Nordson Ultimus V Bedienungsanleitung

Nordson

Nordson SEE-FLO 7 Referenzhandbuch

Nordson

Nordson VersaBlue Bedienungsanleitung

Nordson

Nordson ProBlue Fulfill Referenzhandbuch

Nordson

Nordson EFD 1500 Series Bedienungsanleitung

Nordson

Nordson Asymtek M-2000 Installationsanleitung

Nordson

Nordson Ultimus IV Bedienungsanleitung

Nordson

Nordson ProBlue Fulfill Referenzhandbuch

Nordson

Nordson FP-200 Bedienungsanleitung

Nordson

Nordson UltimusPlus Gebrauchsanweisung

Nordson

Nordson Performus X Series Bedienungsanleitung

Nordson

Nordson EFD 1000 Series Bedienungsanleitung

Nordson

Nordson DispensGun Bedienungsanleitung

Beliebte Spender Handbücher anderer Marken

Silver King

Silver King Majestic SK12MAJ Kurzanleitung

Franke

Franke F3Dn Twin Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON UltraHot Plus Bedienungsanleitung

DAN DRYER

DAN DRYER 282 Bedienungsanleitung

Essity

Essity Tork 473208 Bedienungsanleitung

CBS

CBS SD300BU-88 Einrichtungshandbuch

Sealey

Sealey MK77 Bedienungsanleitung

Fluid Management

Fluid Management Accutinter 1600 Bedienungsanleitung

Franke

Franke DVS SD99-010 Bedienungsanleitung

Graco

Graco Dispensit 1053-10C Fehlerbehebungshandbuch

ITALTINTO

ITALTINTO i50 Bedienungsanleitung

Coca-Cola

Coca-Cola FREESTYLE 9000 Bedienungsanleitung

Graco

Graco ProMix 2KE Bedienungsanleitung

TECHCON SYSTEMS

TECHCON SYSTEMS TS1251 Bedienungsanleitung

Wayne

Wayne GLOBAL VISTA CNG Bedienungsanleitung

clarsen

clarsen H133 Bedienungsanleitung

PicoBrew

PicoBrew Zymatic Bedienungsanleitung

BOWMAN

BOWMAN BP-007 Bedienungsanleitung