Norton Clipper CS1-500 P13 Bedienungsanleitung

CS1 –500 P13

OPERATING INSTRUCTIONS

Translation of the original instructions

VERS.2022.10.20 CS1-500_MAN_EN

The undersigned manufacturer:

SAINT - GOBAIN ABRASIVES S.A.

190, BD. J. F. KENNEDY

L-4930 BASCHARAGE

Declares that this product:

« Floor saw »: CS1-500 P13 HONDA Code : 70184632006

is in conformity with the following Directives :

"MACHINES" 2006/42/CE

"ELECTROMAGNETIC COMPATIBILITY" 2014/30/UE

"NOISE" 2000/14/CE

And the European standard:

EN 13862 –Floor cutting-off machines –Safety

Valid for machines as of serial number: 4503103257

Storage site for the technical documents:

Saint-Gobain Abrasives 190, Bd. J. F. Kennedy 4930 BASCHARAGE, LUXEMBOURG

This declaration of conformity loses its validity when the product is converted or modified without

agreement.

Bascharage, Luxembourg, 20/10/2022.

François Chianese, executive officer.

Declaration of conformity

VERS.2022.10.20 CS1-500_MAN_EN

The undersigned manufacturer:

SAINT - GOBAIN ABRASIVES S.A.

190, BD J.F. KENNEDY

L- 4930 BASCHARAGE

Declares that this product:

« Floor saw »: CS1-500 P13 HONDA Code : 70184632006

is in conformity with the following standard:

Supply of Machinery (Safety) Regulations 2008

Electromagnetic Compatibility Regulations 2016

Noise Emission in the Environment by Equipment

for use Outdoors Regulations 2001

and European standard:

EN 13862 –Floor cutting-off machines –Safety

Valid for machines with a serial number greater than: 4503103257

Authorised Representative:

SAINT-GOBAIN ABRASIVES

Unicorn House • Unit 1, Amison Close

Redhill Business Park • Stafford • England • ST16 1WB

This declaration of conformity loses its validity when the product is converted or modified without

agreement.

Bascharage, Luxembourg, 20/10/2022.

François Chianese, executive office.

Declaration of conformity

VERS.2022.10.20 CS1-500_MAN_EN

CS1-500

OPERATING INSTRUCTIONS

1BASIC SAFETY INSTRUCTIONS 6

1.1 Symbols 6

1.2 Machine plate 7

1.3 Safety instructions for particular operating phases 8

2GENERAL DESCRIPTION OF THE CS1-500 9

2.1 Short description 9

2.2 Layout 9

2.3 Technical data 12

2.4 Statement regarding the vibration emission 13

2.5 Statement regarding noise emission 14

3ASSEMBLY AND COMMISSIONING 15

3.1 Tool assembly 15

3.2 Water cooling system 15

3.3 Starting the machine 16

4OPERATING THE CS1-500 17

4.1 Site of work 17

4.2 Cutting method 17

5TRANSPORT AND STORING 18

5.1 Securing for transport 18

5.2 Transport procedure 18

5.3 Long period of inactivity 18

6MAINTENANCE AND SERVICE 19

6.1 Maintenance of the machine 19

6.2 Maintenance of the engine 20

7FAULTS: CAUSES AND CURES 23

7.1 Fault-finding procedures 23

7.2 Trouble-shooting guide 23

7.3 Customer service 24

7.4 Spare parts 25

VERS.2022.10.20 CS1-500_MAN_EN

1 BASIC SAFETY INSTRUCTIONS

The CS1-500 is exclusively designed for the cutting of floors made of asphalt, green and cured

concrete (reinforced or not) as well as of industrial cement.

Uses other than the manufacturer's instructions shall be considered as contravening the

regulations. The manufacturer shall not be held responsible for any resulting damage. Any risk

shall be borne entirely by the user. Observing the operating instructions and compliance with

inspection and servicing requirements shall also be considered as included under use in

accordance with the regulations.

1.1 Symbols

Important warnings and pieces of advice are indicated on the machine using symbols. The

following symbols are used on the machine:

Read operator’s instructions

Ear protection must be worn

Hand protection must be worn

Eye protection shall be worn

The rotation of the hand wheel in the

direction shown : up or down the blade

Danger: risk of cut

VERS.2022.10.20 CS1-500_MAN_EN

Never move the machine with the blade

running idle.

Rotation direction of the blade

Emergency Stop

1.2 Machine plate

Important data can be found on the following plate located on the machine:

Ø Bore

Machine type

Serial number

Power

Safety standard

Machine Model

Machine Code

Blade speed

Weight

Year of

production

ØMaximum

blade

VERS.2022.10.20 CS1-500_MAN_EN

1.3 Safety instructions for particular operating phases

Before commencing work

Before commencing work, make yourself familiar with the working environment at the place

of use. The working environment includes: obstacles in the area of work and manoeuvre, the

firmness of the floor, necessary protection at the site relating to public thoroughfares and the

availability of help in the event of accidents.

Check for correct mounting of the blade regularly.

Immediately remove damaged or badly worn blades, as they endanger the operator whilst

rotating.

Always cut with the blade guard in position.

Only fit NORTON diamond blades to the machine! The use of other tools can damage the

machine!

Attention is drawn to the use of BS2092 safety goggles in conformitywith specified Processes

No.8 of the Protection of Eyes Regulation 1974, Regulation 2(2) Part 1.

For security reasons, never leave the machine unattended, untied or unlocked.

While the engine is running

Do not move the machine whilst the blade is running idle.

Do not run the machine without the security guards in place.

Apply cooling water continuously whilst cutting and in good time!

Diesel powered machines:

Always use the fuel advised.

In confined areas, exhaust gases should be evacuated and the job site properly aerated.

Diesel machines, which by their nature emit toxic exhaust gases, must not be used in places

prohibited by the Health at Work Act 1974 or which are prohibited by Factory Inspectors or

Safety Officers.

Diesel is flammable. Before filling the tank, shut down the engine, extinguish all open flames

and do not smoke. Take care that no diesel is spilled on any motor part. Always wipe up

spilled fuel.

VERS.2022.10.20 CS1-500_MAN_EN

2 GENERAL DESCRIPTION OF THE CS1-500

Any modification, which could lead to a change in the original characteristics of the machine, may

be done only by Saint-Gobain Abrasives S.A. who shall confirm that the machine is still in

conformity with the safety regulations. Saint-Gobain Abrasives S.A. keeps the right of making

technical or design modification without prior notification.

2.1 Short description

The Floor Saw CS1-500 you have chosen,is usedfor small repair works in concrete and asphalt,

for cutting induction loops and installing cables as well as for cutting expansion joints. It can be

used for either wet or dry cutting operations. Being of small construction, it can be transported in

a car or van. The water container is enclosed in the frame. All component parts on the CS1-500

are assembled to a high quality standard, ensuring long life, reliability and a minimum of

maintenance. Special types of blades are available for asphalt, green concrete, cured concrete

(reinforced or not) as well as for industrial cement flooring.

2.2 Layout

VERS.2022.10.20 CS1-500_MAN_EN

Made of jig welded open profile steel, the CS1-500 is stable but at the same time, easily

transportable.

The one-piece blade guard (1) fully protects the operator and his working environment. It is firmly

fixed to the main frame but can be opened by rotation to change blades.

A manually operated hand wheel mechanism (2) enables graduated depth setting. Turning the

hand wheel clockwise or anti-clockwise will lower or raise the cutting blade.

The pivoting frame (3), hinged on the rear axle, is supporting the engine, the blade shaft

assembly, and the protecting guards. Four heavy-duty belts drive the blade.

The precisely manufactured blade shaft is fitted into two heavy-duty self-aligning pillow block

bearings, including grease nipples. A four-belt taper lock pulley is fitted on one end. The shaft is

reduced to 25,4mm at the other end, allowing an inner flange complete with dowel pinholes to be

fixed.

The steel belt guard (4) is bolted to the mainframe of the machine. It is covering the four drive

belts and pulleys for protection of the environment while the machine is running. The pointer (5)

allows the operator to make precise cut easily.

The Honda GX390 engine (6) is connected to an emergency shut down switch (7) on the board

of the machine. This allows an immediate stop of the machine in case of danger.

The water cooling system (8) is composed of a 70 litres water tank, a water tank tap and two

water nozzles on the blade guard ensuring adequate flow of water to both sides of the blade.

Inhaltsverzeichnis

Andere Norton Gesehen Handbücher

Norton

Norton BBL547 Bedienungsanleitung

Norton

Norton Clipper C13PE Bedienungsanleitung

Norton

Norton BBL547 Bedienungsanleitung

Norton

Norton Blockbuster BBL727 Bedienungsanleitung

Norton

Norton CGW 1.30.1 230V Bedienungsanleitung

Norton

Norton clipper CHW Series Bedienungsanleitung

Norton

Norton C3120 Bedienungsanleitung

Norton

Norton Clipper TR 232 S Bedienungsanleitung

Norton

Norton TT 200 EM Bedienungsanleitung

Norton

Norton clipper CM 350 B Bedienungsanleitung

Norton

Norton GC55 Bedienungsanleitung

Norton

Norton clipper CM 450 Junior Bedienungsanleitung

Norton

Norton clipper CS 502LV P13 Bedienungsanleitung

Norton

Norton Clipper CB 311 Bedienungsanleitung

Norton

Norton BBL547 Bedienungsanleitung

Norton

Norton clipper CGW EVO D400 Bedienungsanleitung

Norton

Norton CST 65 Modulo Bedienungsanleitung

Norton

Norton Clipper CTC1020XL Bedienungsanleitung

Norton

Norton CS 451 P13 Leitfaden

Norton

Norton Clipper CS1 P13 Bedienungsanleitung

Norton

Norton TR 230 GS Bedienungsanleitung

Norton

Norton Clipper ISM Bedienungsanleitung

Norton

Norton clipper CMR 351 Bedienungsanleitung

Norton

Norton Clipper C1318P Bedienungsanleitung

Beliebte Gesehen Handbücher anderer Marken

RIDGID

RIDGID BS1400 Bedienungsanleitung

ATIKA

ATIKA BWS 400-2 Bedienungsanleitung

RGC

RGC FS20 Bedienungsanleitung

Makita

Makita M2300 Bedienungsanleitung

IMET Spa

IMET Spa BASIC 300 PLUS SHI Bedienungsanleitung

IMET Spa

IMET Spa SIRIO 370 AF-E Bedienungsanleitung

Optimum

Optimum OPTisaw CS 275 Bedienungsanleitung

Makita

Makita BPB180 Bedienungsanleitung

Stihl

Stihl MS 462 C-M Bedienungsanleitung

AEG

AEG TS 250 K Bedienungsanleitung

Meec tools

Meec tools 004665 Bedienungsanleitung

Makita

Makita LS1018L Bedienungsanleitung

Ryobi

Ryobi RCS1400 Bedienungsanleitung

DeWalt

DeWalt DCS391 Bedienungsanleitung

Sealey

Sealey SA72 Bedienungsanleitung

skilsaw

skilsaw SPT88 Montageanleitung

Urrea

Urrea SI810 Abmessungen und Installationsanleitung

EINHELL

EINHELL BKG 210/1 Bedienungsanleitung

Norton clipper CS1-500 P13 Bedienungsanleitung

Beliebte Gesehen Handbücher anderer Marken