Norton Clipper C1318P Bedienungsanleitung

OWNERS

MANUAL

Small Concrete Saw

MODEL:

C1318P

FORM: C1318P rev 4-2017

WARRANTY

Norton warrants all products manufactured by it against defects in

workmanship or materials for a period of one (1) year from the date of

shipment to the customer.

The responsibility of Norton under this warranty is limited to

replacement or repair of defective parts at Norton's Gainesville,

Georgia factory, or at a point designated by it, of such part as shall

appear to us upon inspection at such point, to have been defective in

material or workmanship, with expense for transportation borne by the

customer.

In no event shall Norton be liable for consequential or incidental

damages arising out of the failure of any product to operate properly.

Integral units such as gasoline engines, electric motors,batteries,

tires, transmissions, etc., are excluded from this warranty and are

subject to the prime manufacturer's warranty.

This warranty is in lieu of all other warranties, expressed or implied,

and all such other warranties are hereby disclaimed.

Important: Before placing equipment in operation, record the following

information.

MODEL:_________ SERIAL NO.___________

PURCHASE FROM: _____________________

ADDRESS: ____________________________

CITY_______ STATE ______ ZIP ________

TELEPHONE NO. ______________________

Before using this equipment, make sure that any person using it

reads and understands the instructions in this owner’s manual.

Table of Contents

CONTENTS PAGE

I. Preparation

A. Safety Precautions 4-6

B. Assembly 7

C. C1318P Series Concrete Saw Specifications 8

D. Engine Specifications 9

E. Pointer Alignment 9

II. Operation

A. Blade Installation 9-10

B. Starting The Engine 10-11

C. Water Supply 12

D. Operating The Saw 12-13

E. Cutting Technique 13

III. Maintenance

A. Engine 14-15

B. Bearings 15-16

C. V-Belts 16-20

D. Depth Control 21

IV. Parts List Section

A. Ordering Information 22

B. Parts Drawing and Service Parts List 23-33

Depth Control And Depth Lock Group 23

Handle Bar Group 24

Blade Guard Group 25

Blade Shaft Group 26-27

Belt Tensioning Group 28

Engine Mount Group 29

Main Frame Group 30

Water Control Group 31-32

Front Pointer Group 33

Read Owners Manual Before Use

Safety Alert Symbol: Information Following This Symbol Is

Very Important.

Use Only Norton Diamond Blades

I. PREPARATION

A. Safety Precautions

Important! The following safety precautions must always be observed.

Hazard Symbols

Fuel (gasoline) is extremely flammable and its vapors can

explode if ignited. Store gasoline only in approved containers,

in well-ventilated, unoccupied approved areas, and away from

sparks or flames. Do not fill the fuel tank while the engine is hot

or running. Do not start the engine near spilled fuel. Never use

the fuel as a cleaning agent

Engine components can get extremely hot from operation. To

prevent burns, do not touch the engine or related parts while the

engine is running or immediately after it is turned off. Never

operate the engine with any heat shields or guards removed.

Keep all guards in place when operating any piece of equipment

Keep hands, feet, hair, and clothing away from all rotating parts

Lethal Exhaust Gas: use only in well ventilated areas. Engine

exhaust gases contain poisonous carbon monoxide, which is

odorless, colorless, and can cause death if inhaled. Avoid

inhaling exhaust fumes, and never run the engine in a closed

building or confined area.

Never tamper with the governor components of settings to

increase the maximum speed. Severe personal injury and

damage to the engine or equipment can result if operated at

speed above maximum. Always obey the maximum speed

rating of blade.

DO NOT LIFT THE SAW BY THE HANDLE

BARS

Dust and Silica Warning

Grinding/cutting/drilling of masonry, concrete, metal and other materials can

generate dust, mists and fumes containing chemicals known to cause serious or

fatal injury or illness, such as respiratory disease, cancer, birth defects or other

reproductive harm. If you are unfamiliar with the risks associated with the

particular process and/or material being cut or the composition of the tool being

used, review the material safety data sheet and/or consult your employer, the

material manufacturer/supplier, governmental agencies such as OSHA and

NIOSH and other sources on hazardous materials and make certain to comply

with all product warnings and instructions for the safe and effective use of the

material being cut. California and some other authorities, for instance, have

published lists of substances known to cause cancer, reproductive toxicity, or

other harmful effects.

Control dust, mist and fumes at the source where possible. In this regard use

good work practices and follow the recommendations of the manufacturer/supplier,

OSHA/NIOSH, and occupational and trade associations. Water should be used

for dust suppression when wet cutting is feasible. When the hazards from

inhalation of dust, mists and fumes cannot be eliminated through engineering

controls such as vacuum and/or water mist, the operator and any bystanders

should always wear a respirator approved by NIOSH/MSHA for the material being

cut.

Use Approved:

Eye Protection Hearing

Protection

Respiratory

Protection

Head Protection

1. Before mounting any blade on the saw, the blade should be inspected for

any damage which might have occurred during shipment, handling or

previous use.

2. The blade collars and arbors should be cleaned and examined for damage

before mounting the blade.

3. The blade must be properly fitted over the arbor with the drive pin on the

outside collar projecting through the drive pin hole on the blade and

inside collar.

4. The blade shaft nut, which is a left-hand thread nut, must be tightened

securely against the outside blade shaft collar.

5. The blade must be operated within the specified maximum operating

speed listed on the blade.

6. Turn water control valve to full to provide adequate coolant (4 to 6 gallons

per minute) for diamond blades and wet cutting abrasive blades.

Insufficient coolant could result in severe blade breakage or diamond

segment separation.

7. The blade guard must be in place with the nose guard down and locked

when the saw is running.

8. The operator should wear safety glasses and any other appropriate safety

equipment.

9. When starting the saw, the operator should stand away and to the side of

the blade.

10.If for any reason the saw should stall in the cut, raise the blade out of the

cut. Check the outside blade shaft collar and nut for tightness. Inspect

the blade for damage before restarting the saw. Use caution when

resuming a cut. Be certain that the blade is in alignment with the previous

cut.

11.During cutting operations do not exert excess side pressure on the

handles as a method of steering. Do not force the blade into the cut by

lowering the blade too fast or by pushing the saw too fast.

You Are Responsible For Your Safety!!!

I. PREPARATION

B. Assembly

The compact concrete saws are shipped completely assembled and ready for

use except for diamond blade, gasoline, oil, and handle bar. Inspect the saw

for shipping damage. If any damage is found, contact the shipper immediately

and file a freight claim. Norton Clipper is not responsible for any freight-related

damages. Remove the saw from the pallet. Reverse the position of the

handlebars so that the handle bar sticks out towards the operator. Adjust the

handlebars to the desired height. Align the hole located in the operator’s right

side of the Handle Bar Assembly with the M10 Weld Nut in the frame. Attach

the handlebars to the saw with the supplied hardware. The Operator’s Right

Side Screw part# 028098 will pass through a hole in the Handle Bar Assembly.

Tighten 029098 to the Handle Bar Assembly and then tighten the M10 Jam Nut

027006. Tighten 027021 to the Handle Bar Assembly and then tighten the

M10 Jam Nut 027006. Read and understand the remaining sections of this

Owners Manual. NOTE: Do not install the blade until it is time to use the saw.

ANSI regulations prohibit the transportation of any concrete saw with the blade

installed.

DO NOT LIFT THE SAW BY THE HANDLE BARS

Part # Description QTY

027021 Screw DIN931 M10 x 25 Hex Head Cap 1

028098 Screw DIN933 M10 x 65 Hex Head Cap 1

027006 M10 Jam Nut DIN934 2

027021

028098

027006

M10 Weld

Nut

C. C1318P Series Concrete Saw Specifications

Dimensions/Weight

Length (Working) 45.66” (1160 mm)

Length (Transport) 33.50” (850 mm)

Width 39.50” (1003 mm)

Height 39” (990 mm)

Weight 220 lbs (100 kg)

Engine

Engine Mfg. Honda

Spec No. GX390K1QXC9

Engine Type Single Cylinder 4 Cycle

Horse Power - Gross 13 hp* (9.5kW) @ 3,600 rpm

Max Torque – Gross 19.5 ft-lbs (26.5 Nm, 2.7 kg-m) @ 2,500 rpm

Model GX390K1QXC9

Model GX390

Cooling System Air

Oil Capacity 1.16 US qt (1.1 liter)

Fuel Capacity 1.79 US gal (6.5 liter)

Fuel Type Unleaded Gasoline (86 pump octane)

Low Oil Sensor Yes

Air Filtration Four Stage Cyclone

Characteristics

Max Blade 18” (450 mm)

Depth of Cut 18” (406 mm) 6.75” (172 mm)

16” (406 mm) 5.75” (146 mm)

14” (356 mm) 4.75” (121 mm)

12” (305 mm) 3.75” (95 mm)

Arbor Bore 1” (25.4 mm)

Blade Shaft Locking Device Machined Into Flats Of Tight Collar

Blade Shaft Speed 2,573 rpm

Depth Control Hand Wheel With Screw Feed

Depth Lock Standard

Depth Gauge Customer Installed Accessory

Number Of Belts Single Ten (10) Groove K Section Belt

Blade Guard Type Hinged, All Steel Construction

Right or Left Side Cutting Yes

Lifting Bale Built In

Handle Bars Adjustable, Stays Level At All Times

Water Tank Standard

Water Tank Capacity 6.5 US Gallons (24.6 liter)

Water Hose Connector Standard Garden Hose With Flow Control Valve

Recessed Rear Wheels Standard

Sound pressure

88 db(A)

Sound power

105 db(A)

Vibration emission value 9.18 ft/ s² (2.8 m/s²) (according to EN 12096)

* = Horse power and Torque ratings are Gross Horse power and are supplied by the engine manufacturer. Actual output of the engine will vary due to many

factors including operational speed of engine, environmental conditions, maintenance, fuel, and other variables. Saint-Gobain Abrasives, Inc. makes NO

claim to actual or gross horse power and torque ratings. 1) The sound measures have been made following pr EN 12638, Annex A; 2)“Floor sawing,

grooving and milling machines – Safety “

D. Engine

Prior to attempting to operate the engine, read the information

contained in the engine owner's manual. An engine owner’s manual is

supplied with every gasoline powered concrete saw.

1. Check Oil: Add oil if low. Refer to the engine owner's manual for the

recommended SAE viscosity grades. Capacity of oil is 1.16 US quarts (1.1

liters)

2. Check Fuel: Fill if low. Use only unleaded gasoline with a pump sticker

octane rating of 86 or higher is recommended. Never use an oil and

gasoline mixture!

3. Air Cleaner: Never run the engine without the air cleaner! Rapid engine

wear will result from contaminants being drawn through the carburetor and

into the engine.

4. Engine Starting: Refer to the engine owner's manual additional proper

engine starting procedure.

E. Pointer Alignment

1. Use a straight edge, and carefully mark a line 12 feet long on a smooth level

surface.

2. Place the saw blade on the marked line, move the saw to the center of the

marked line and then lower the blade until it is about 1/16” above the

marked line

3. Measure from each end of the saw frame to insure that the frame is parallel

to the marked line. Adjust the saw as needed.

4. With the blade centered on the marked line and the saw frame parallel to

the marked line, lower the front pointer.

5. Adjust the pointer by bending it until is aligned with the marked line.

II. OPERATION

A. Installing the Blade

1. Disconnect the spark plug.

2. Remove the blade shaft nut, (Turn clockwise),and remove the outside

collar.

3. Clean off any foreign particles on the clamping surfaces of both collars

and on the mounting surface of the blade.

4. Place the blade on the blade shaft, lining up the drive pin hole in the

blade with the drive pinhole in the inside collar.

For Best Performance Use Only Norton Diamond Blades

Specified For the Material Being Cut.

5. Slide the outside blade shaft collar onto the blade shaft. The drive pin

on the outside collar must project through the drive pin hole in the blade

and into the inside collar.

6. Tighten the blade shaft nut (counter-clockwise) securely against the

outside collar.

7. Reconnect the spark plug.

B. Starting the Engine

1. Refer to the engine owner's manual for detail starting procedures.

2. Always cut with engine rpm in the full throttle setting.

Before starting, insure that the blade is properly installed,

all guards are in place and in safe operating condition, and

that the Blade is not in contact with any surface or object.

Also verify that the area where the work is to be preformed

is clean, safe, and has proper ventilation and lighting.

Always located and properly mark all water, gas, and

electrical services before beginning any work.

Inhaltsverzeichnis

Andere Norton Gesehen Handbücher

Norton

Norton clipper CS 502LV P13 Bedienungsanleitung

Norton

Norton CGW 1.30.1 230V Bedienungsanleitung

Norton

Norton BBC157 Bedienungsanleitung

Norton

Norton clipper CMR 351 Bedienungsanleitung

Norton

Norton clipper CS 352 Bedienungsanleitung

Norton

Norton Clipper C13PE Bedienungsanleitung

Norton

Norton TC-405 Bedienungsanleitung

Norton

Norton GC55 Bedienungsanleitung

Norton

Norton Clipper CS 401 P13 Bedienungsanleitung

Norton

Norton clipper CHW Series Bedienungsanleitung

Norton

Norton Clipper C1418P Bedienungsanleitung

Norton

Norton Clipper Blockbuster BBC347 Bedienungsanleitung

Norton

Norton Clipper CMV 1000 Verto Bedienungsanleitung

Norton

Norton JCW 600 Bedienungsanleitung

Norton

Norton Blockbuster BBL727 Bedienungsanleitung

Norton

Norton TR 230 GL Leitfaden

Norton

Norton Clipper CB 311 Bedienungsanleitung

Norton

Norton C3120 Bedienungsanleitung

Norton

Norton Clipper TR 232 S Bedienungsanleitung

Norton

Norton CS 451 P13 Leitfaden

Norton

Norton clipper CP512-300 Bedienungsanleitung

Norton

Norton TT 250 G Bedienungsanleitung

Norton

Norton clipper TR 231 GL Bedienungsanleitung

Norton

Norton TR 250 H Clipper Bedienungsanleitung

Beliebte Gesehen Handbücher anderer Marken

RIDGID

RIDGID BS1400 Bedienungsanleitung

ATIKA

ATIKA BWS 400-2 Bedienungsanleitung

RGC

RGC FS20 Bedienungsanleitung

Makita

Makita M2300 Bedienungsanleitung

IMET Spa

IMET Spa BASIC 300 PLUS SHI Bedienungsanleitung

IMET Spa

IMET Spa SIRIO 370 AF-E Bedienungsanleitung

Optimum

Optimum OPTisaw CS 275 Bedienungsanleitung

Makita

Makita BPB180 Bedienungsanleitung

Stihl

Stihl MS 462 C-M Bedienungsanleitung

AEG

AEG TS 250 K Bedienungsanleitung

Meec tools

Meec tools 004665 Bedienungsanleitung

Makita

Makita LS1018L Bedienungsanleitung

Ryobi

Ryobi RCS1400 Bedienungsanleitung

DeWalt

DeWalt DCS391 Bedienungsanleitung

Sealey

Sealey SA72 Bedienungsanleitung

skilsaw

skilsaw SPT88 Montageanleitung

Urrea

Urrea SI810 Abmessungen und Installationsanleitung

EINHELL

EINHELL BKG 210/1 Bedienungsanleitung