NorwellVR. NWJR503 Bedienungsanleitung

IN-GROUND

INSTALLATION MANUAL

INSTALLATION MANUAL ·IN-GROUND

Dig holes according to positions on

drawings (see the following pages).

Tighten the anchors (M12 = 90 N/m

and M16 = 120 N/m).

Dimensions of holes:

e.g. 50 x 50 x 75 cm (see the

following pages).

Drill bolt holes with a concrete

hammer.

Make sure the ﬁtness station is stabil

and properly fastened before ﬁlling

with dirt to the surface.

Fill with concrete leaving a depth of

e.g. 25/40 cm (see the following

pages). Dry for approx. 6-7 days.

Mount the M12/M16 concrete

bolts.

REQUIREMENTS FOR THE CONCRETE

The concrete must comply with the standard EN197-1 CEM I 52,5 N.

Mixing ratio: Cement 1/8

Sand 3/8 (max. stone size 4mm)

Stones 4/8 (stone size 16mm)

The concrete must be premixed or mixed in a mixer. Hand mixing is not

acceptable.

For the concrete to settle, it must be vibrated with a concrete vibrator.

To ensure correct contact between the base plate and the concrete, the

concrete surface must be 100% plane.

The concrete has to have the strength of ≥52,5 MPa (obtained in approx.

7 days, but longer in cold weather).

The installation must be carried out by professionals and according to current

practice.

NWJR102

Junior Back

NWJR101

Junior Chest

2,10m

INSTALLATION MANUAL ·IN-GROUND

See separate page with the

preparatory work for in-ground

installation.

• Install onto a concrete block.

• Assemble and line up.

• Place on concrete.

• Mark position of bolt holes.

• Fasten each base plate with

4 x M16 bolts.

POSITION AND TRAINING ZONE: DEPTH:

PART LIST:

4 x M16

BASE PLATE:

40 x 40cm

0,75m

0,25m

0,50m

0,70m

CONCRETE

BLOCK

NWJR103 Junior Sit Up

INSTALLATION MANUAL ·IN-GROUND

See separate page with the

preparatory work for in-ground

installation.

• Install onto 2 concrete blocks.

• Assemble and line up.

• Place on concrete.

• Mark position of bolt holes.

• Fasten each base plate with

4 x M12 bolts.

POSITION AND TRAINING ZONE: DEPTH:

0,50m

0,75m

0,25m

CONCRETE

BLOCK

PART LIST:

8 x M12

BASE PLATE:

25 x 25cm

NWJR104 Junior Pull Up

2,12m

INSTALLATION MANUAL ·IN-GROUND

See separate page with the

preparatory work for in-ground

installation.

• Install onto 2 concrete blocks.

• Assemble and line up.

• Place on concrete.

• Mark position of bolt holes.

• Fasten each base plate with

4 x M16 bolts.

POSITION AND TRAINING ZONE: DEPTH:

0,50m

1,00m

0,75m

0,25m

CONCRETE BLOCK

PART LIST:

8 x M16

BASE PLATE:

40 x 40cm

NWJR105 Junior Bar

INSTALLATION MANUAL ·IN-GROUND

See separate page with the

preparatory work for in-ground

installation.

• Install onto 2 concrete blocks.

• Assemble and line up.

• Place on concrete.

• Mark position of bolt holes.

• Fasten each base plate with

4 x M12 bolts.

POSITION AND TRAINING ZONE: DEPTH:

0,50m

0,75m

0,25m

CONCRETE

BLOCK

PART LIST:

8 x M12

BASE PLATE:

25 x 25cm

NWJR201 Junior Double Air Walker

INSTALLATION MANUAL ·IN-GROUND

See separate page with the

preparatory work for in-ground

installation.

• Install onto 6 concrete blocks.

• Assemble and line up.

• Place on concrete.

• Mark position of bolt holes.

• Fasten each base plate with

4 x M12 bolts.

ASSEMBLING:

POSITION AND TRAINING ZONE: DEPTH:

0,50m

0,75m

0,25m

CONCRETE

BLOCK

PART LIST:

24 x M12

2 x cross bar

2 x sets of Nut caps, round

4 x M10 x 110 bolts

4 x Stainless Steel connector

Always secure

bolts with

Loctite.

BASE PLATE:

25 x 25cm

NWJR202 Junior Cross

1,42m / 4’7”

INSTALLATION MANUAL ·IN-GROUND

See separate page with the

preparatory work for in-ground

installation.

• Install onto a concrete block.

• Assemble and line up.

• Place on concrete.

• Mark position of bolt holes.

• Fasten each base plate with

4 x M16 bolts.

POSITION AND TRAINING ZONE: DEPTH:

PART LIST:

4 x M16

BASE PLATE:

40 x 40cm

0,50m

0,70m

0,90m

0,40m

CONCRETE

BLOCK

NWJR203 Junior Hip

INSTALLATION MANUAL ·IN-GROUND

See separate page with the

preparatory work for in-ground

installation.

• Install onto 2 concrete blocks.

• Assemble and line up.

• Place on concrete.

• Mark position of bolt holes.

• Fasten each base plate with

4 x M12 bolts.

POSITION AND TRAINING ZONE: DEPTH:

0,50m

0,75m

0,25m

CONCRETE

BLOCK

PART LIST:

8 x M12

BASE PLATE:

25 x 25cm

NW501 Bench

INSTALLATION MANUAL ·IN-GROUND

See separate page with the

preparatory work for in-ground

installation.

• Install onto 4 concrete blocks.

• Assemble and line up.

• Place on concrete.

• Mark position of bolt holes.

• Fasten each base plate with

4 x M12 bolts.

ASSEMBLING:

POSITION AND TRAINING ZONE: DEPTH:

0,50m

0,75m

0,25m

CONCRETE

BLOCK

PART LIST:

16 x M12

4 x sets of Nut caps, round

4 x M10 x 110 bolts

Always secure

bolts with

Loctite.

BASE PLATE:

25 x 25cm

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

norwellVR. NWJR503 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken