NXP Semiconductors LPC553 Series Bedienungsanleitung
AN13707
Hardware Design Guidelines for LPC553x/LPC55S3x Microcontrollers
Rev. 1 — 4 September 2023 Application note
Document Information
Information Content
Keywords Hardware Design Guidelines, LPC553x
Abstract This document guides hardware engineers to design and test their LPC553x/S3x controller-based
designs. The document provides information about board layout recommendations and design
checklists.
NXP Semiconductors AN13707
Hardware Design Guidelines for LPC553x/LPC55S3x Microcontrollers
1 Introduction
This document helps the hardware engineers to design and test their LPC553x/S3x controller-based designs.
The document provides information about board layout recommendations and design checklists to ensure first-
pass success and avoid any board bring-up problems.
This document only focuses on LPC553x/S3x.
Note: LPC553x/S3x devices are not pin-to-pin compatible with other LPC55 series devices.
This guide is released with the relevant device-specific hardware documentation such as data sheets, reference
manuals, and application notes available on www.nxp.com.
2 LPC553x/S3x family comparison
All LPC553x/S3x family is based on the Arm Cortex-M33 core, with PowerQuad Accelerator, enhanced timer,
and analog features to support motor control applications. The ‘S’ in the middle of the part name means that this
part provides more security features, such as TrustZone Support.
Type number Flash/
KB
Total
RAM/KB
CAN FD USB GPIO Flex SPI ADC
channel
DAC
outputs
Internal
DAC
Comparator Tamper
pins
OP Amp CRC/1/2/3 DMIC
LPC5536JBD100 256 128 Y FS 66 Y 23 2 1 4 4 3 Y Y
LPC5536JBD64 256 128 Y - 39 Y 13 1 2 4 2 3 Y y
LPC5534JBD100 128 96 Y FS 66 Y 23 2 1 4 4 3 Y Y
LPC5534JBD64 128 96 Y - 39 Y 12 1 2 4 2 3 Y y
LPC5534JHI48 128 96 Y - 32 Y 10 - 1 4 2 3 Y Y
LPC5536JHI48 256 128 Y - 32 Y 10 - 1 4 2 3 Y Y
Table 1. LPC553x/S3x family core features
Note: The last 18 pages (9 KB) are reserved on the 256 KB flash devices for the Protected Flash Region
(PFR), resulting in 247 KB of internal flash memory for the user.
For more information, refer to the latest version of the Datasheet and Reference Manual (RM) from
www.nxp.com.
3 Power supply
This section gives details of the power supply for the LPC553x/S3x series.
3.1 Introduction
LPC553x/S3x series require a single operating voltage supply on MCU VDD_MAIN/VDD_MAIN_PWR pins
(1.8 V to 3.6 V), two main I/O supplies on VDDIO_1 (1.8 V to 3.6 V) and VDDIO_2 (1.08 V to 3.6 V) pins, and a
separate Battery Supply (VBAT) on VBAT pin (1.71 V to 3.6 V).
LPC553x/S3x internal core’s voltage is supplied by an internal DC-DC regulator or selectable LDO such that the
DC-DC converter can be bypassed.
Refer to Using the DC-DC and LDO Features on the LPC553x/LPC55S3x Family (document AN13528) for
details.
AN13707 All information provided in this document is subject to legal disclaimers. © 2023 NXP B.V. All rights reserved.
Application note Rev. 1 — 4 September 2023
2 / 25
NXP Semiconductors AN13707
Hardware Design Guidelines for LPC553x/LPC55S3x Microcontrollers
C4
47 pF
C3
100 nF
C2
22 μF
C5
47 pF
C5
100 nF
C5
4.7 μF
C1
22 μF
L1
4.7 μH
LPC553x
VDD_MAIN_PWR
VDD_MAIN VBAT
LX
VSS_MAIN VSS_MAIN_PWR
VDD_CORE(1.0-1.2 V)
MCU MAIN
1.9 V/3.3 V
MCU VBAT
1.9 V/3.3 V
Figure 1. Using internal DC-DC converter
C4
47 pF
C3
100 nF
C2
22 μF
C5
47 pF
C5
100 nF
C5
4.7 μF
C1
4.7 μF
LPC553x
VDD_MAIN_PWR
VDD_MAIN VBAT
VSS_MAIN VSS_MAIN_PWR
VDD_CORE
MCU MAIN
1.9 V/3.3 V
MCU VBAT
1.9 V/3.3 V
Figure 2. Using internal LDO
3.2 Two I/O power supplies
LPC553x/S3x have two I/O supplies, VDDIO_1 and VDDIO_2.
VDDIO_1 supports 1.8 V to 3.6 V.
VDDIO_2 supports 1.08 V to 3.6 V.
Pin GPIO pins
VDDIO_1 PIO0_1
PIO0_7 to PIO0_8
PIO0_10 to PIO0_12
PIO0_15 to PIO0_17
PIO0_23
PIO0_27
PIO0_31
PIO1_0
PIO1_5 to PIO1_10
PIO1_19 to PIO1_24
Table 2. LPC553x/S3x power supply for pins
AN13707 All information provided in this document is subject to legal disclaimers. © 2023 NXP B.V. All rights reserved.
Application note Rev. 1 — 4 September 2023
3 / 25
NXP Semiconductors AN13707
Hardware Design Guidelines for LPC553x/LPC55S3x Microcontrollers
Pin GPIO pins
PIO2_0 to PIO2_1
RESETN
VDDIO_2 P0_0
P0_2 to P0_6
P0_9
P0_13 to P0_14
P0_18 to P0_22
P0_24 to P0_26
P0_28 to P0_30
P1_1 to P1_4
P1_11 to P1_18
P1_25 to P1_31
Table 2. LPC553x/S3x power supply for pins...continued
3.3 Separate VBAT
LPC553x/S3x’s VBAT pin requires a separate power supply with the range from 1.71 V to 3.6 V.
3.4 Bulk and decoupling capacitors
The effectiveness of the bulk and the decoupling capacitors depends on the optimum placement and connection
type. The bulk capacitors are used for a local power supply to the power pin, near the decoupling capacitors,
and as close as possible to the assigned reference voltage pin. Decoupling capacitors make the current loop
between supply, MCU, and reference ground as short as possible to reduce high-frequency transients and
noises. Therefore, all decoupling capacitors must be placed as close as possible to the devices power supply
pins. In two-layer and multilayer PCBs, the ground side of the decoupling capacitor must have a via to the pad,
which goes directly down to the internal ground plane. The route distance between the capacitors to the power
plane must be as short as possible.
V
i
a
t
o
V
D
D
p
l
a
n
e
V
i
a
t
o
V
D
D
p
l
a
n
e
V
i
a
t
o
G
N
D
p
l
a
n
e
V
i
a
t
o
G
N
D
p
l
a
n
e
C
o
o
p
e
r
p
o
u
r
G
R
O
U
N
D
p
l
a
n
e
L
o
c
a
l
c
u
r
r
e
n
t
l
o
o
p
G
N
D
V
D
D
V
D
D
V
D
D
V
S
S
D
e
c
o
u
p
l
i
n
g
c
a
p
a
c
i
t
o
r
S
i
d
e
v
i
e
w
D
e
c
o
u
p
l
i
n
g
c
a
p
a
c
i
t
o
r
Figure 3. Bulk and decoupling capacitor connection
4 Clock circuitry
This section gives details of the clock circuitry.
AN13707 All information provided in this document is subject to legal disclaimers. © 2023 NXP B.V. All rights reserved.
Application note Rev. 1 — 4 September 2023
4 / 25
NXP Semiconductors AN13707
Hardware Design Guidelines for LPC553x/LPC55S3x Microcontrollers
4.1 Introduction
The LPC553x/S3x has the following clock sources:
•Internal Free Running Oscillator (FRO). This oscillator provides a selectable 96 MHz output, and a 12 MHz
output (divided down from the selected higher frequency) that can be used as a system clock. The FRO
is trimmed to +/- 1 % accuracy over the entire voltage and 0 °C to 85 °C. The FRO is trimmed to +/- 2 %
accuracy over the entire voltage and -40 °C to 105 °C.
•32 kHz Internal Free Running Oscillator FRO. The FRO is trimmed to +/- 2 % accuracy over the entire voltage
and temperature range.
•Internal low-power oscillator (FRO 1 MHz) trimmed to +/- 15 % accuracy over the entire voltage and
temperature range.
•Crystal oscillator with an operating frequency of 12 MHz to 32 MHz, and an option for the external clock input
(bypass mode) for clock frequencies of up to 25 MHz.
•Crystal oscillator with 32.768 kHz operating frequency.
•PLL0 and PLL1 allow CPU operation up to the maximum CPU rate without the need for a high-frequency
external clock. PLL0 and PLL1 can run from the internal FRO 12 MHz output the external oscillator, internal
FRO 1 MHz output, or the 32.768 kHz RTC oscillator.
•Clock output function with a divider to monitor internal clocks.
•Frequency measurement unit for measuring the frequency of any on-chip or off-chip clock signal.
•Each crystal oscillator has one embedded capacitor bank, where each can be used as an integrated
load capacitor for the crystal oscillators. Using APIs, the capacitor banks on each crystal pin can tune the
frequency for crystals with a Capacitive Load (CL) leading to conserving board space and reducing costs.
Note: For external crystal oscillator and RTC oscillator, LPC553x/S3x have a capacitor bank feature. It means
that the stabilizing capacitors can be unsoldered on both 32 kHz and 16 MHz XTAL. We also suggest the user
keep the two stabilizing capacitors as “DNP/Do Not Populate” on PCB.
4.2 Capacitor bank
Each crystal oscillator has one embedded capacitor bank, which is always enabled, and its capacitance can
be adjusted in certain range (IEC equivalent capacitive load: 6 - 10 pF). The capacitor bank can be used as
integrated load capacitors for the crystal oscillators. It helps save external load capacitors of the crystal and
therefore the system BOM cost.
For the capacitor bank usage, refer to Understanding Cap Bank in LPC55(S)xx (document AN13057).
4.3 Crystal oscillator
The crystal oscillator has one embedded capacitor bank that can be used as an integrated load capacitor for the
crystal oscillators. The capacitor bank on each crystal pin can tune the frequency for crystals with a Capacitive
Load (CL) between 6 to 10 pF (IEC equivalent). Simple APIs can be used to configure the capacitor bank based
on the crystal Capacitive Load (CL) and measured PCB parasitic capacitances on the XIN and XOUT pins.
In the crystal oscillator circuit, only the crystal (XTAL) must be connected while the CX1 and CX2 on
XTAL32M_P and XTAL32M_N pins can optionally be connected. No additional capacitance needs to be added
to the PCB when the computation of the required Capacitance Load is less than 20 pF (10 pF equivalent IEC),
When the aforesaid load is greater than 20 pF (10 pF equivalent IEC), additional capacitance is required. (see
Figure 4.) For more information, refer to the Cap Bank API chapter in the LPC553x/S3x Reference Manual.
In bypass mode, an external clock (maximum frequency of up to 25 MHz) can also be connected to
XTAL32M_P if XTAL32M_N is left open. The external [0 – VH] square signal can be applied on the XTAL32M_P
pin from 0 V to 850 mV.
AN13707 All information provided in this document is subject to legal disclaimers. © 2023 NXP B.V. All rights reserved.
Application note Rev. 1 — 4 September 2023
5 / 25
NXP Semiconductors AN13707
Hardware Design Guidelines for LPC553x/LPC55S3x Microcontrollers
LPC
XTAL32M_P XTAL32M_N
CX1 CX2
XTAL
Figure 4. Reference oscillator circuit
Symbol Description
XTAL Quartz Crystal / Ceramic Resonator
CX1 Stabilizing Capacitor
CX2 Stabilizing Capacitor
Table 3. Components of the oscillator circuit
For best results, it is critical to select a matching crystal for the on-chip oscillator. Load Capacitance (CL), Series
Resistance (RS), and Drive Level (DL) are important parameters to consider while choosing the crystal. After
selecting the proper crystal, the external load capacitor CX1 and CX2 values can also be generally determined by
the following expression:
CX1 = CX2 = 2CL - (CPad + CParasitic + Ccapbank)
Where:
CL - Crystal load capacitance
CPad - Pad capacitance of the XTAL32M_P and XTAL32M_N pins (~3 pF).
CParasitic – Parasitic or stray capacitance of external circuit.
Ccapbank – Cap Bank
Although CParasitic can be ignored in general, the actual board layout and placement of external components
influence the optimal values of external load capacitors. Therefore, it is recommended to fine-tune the values
of external load capacitors on the actual hardware board to get an accurate clock frequency. For fine-tuning,
output the RTC Clock to one of the GPIOs and optimize the values of external load capacitors for minimum
frequency deviation. The load capacitors are dependent on the specifications of the crystal and the board
capacitance. It is recommended to have the crystal manufacturer evaluate the crystal on the PCB.
4.3.1 Crystal Printed Circuit Board (PCB) design guidelines
•Connect the crystal and external load capacitors on the PCB as close as possible to the oscillator input and
output pins of the chip.
•The length of traces in the oscillation circuit must be as short as possible and must not cross other signal
lines.
•Ensure that the load capacitors CX1 and CX2, in case of third overtone crystal usage, have a common ground
plane.
•Loops must be made as small as possible to minimize the noise coupled through the PCB and to keep the
parasitic as small as possible.
•Lay out the ground (GND) pattern under the crystal unit.
AN13707 All information provided in this document is subject to legal disclaimers. © 2023 NXP B.V. All rights reserved.
Application note Rev. 1 — 4 September 2023
6 / 25
NXP Semiconductors AN13707
Hardware Design Guidelines for LPC553x/LPC55S3x Microcontrollers
•Do not lay out other signal lines under the crystal unit for multi-layered PCB.
4.4 RTC oscillator
The crystal oscillator has an embedded capacitor bank that can be used as an integrated load capacitor for the
crystal oscillators. The capacitor banks on each crystal pin can tune the frequency for crystals with a Capacitive
Load (CL) between 6 to 10 pF (IEC equivalent). Simple APIs can be used to configure the capacitor banks
based on the crystal Capacitive Load (CL) and measured PCB parasitic capacitances on the XIN and XOUT
pins.
In the RTC crystal oscillator circuit, only the 32.768 kHz crystal (XTAL) needs to be connected while the CX1
and CX2 on XTAL32K_P and XTAL32K_N pins (See Figure 5.) can also optionally be connected. No additional
capacitance needs to be added to the PCB when the computation of the required capacitance load is less
than 20 pF (10 pF equivalent IEC). When this load is greater than 20 pF (10 pF equivalent IEC), additional
capacitance is required. Refer to the Cap Bank API chapter in the LPC553x/S3x Reference Manual.
In bypass mode, an external clock (maximum frequency of up to 100 kHz) can also be connected to
XTAL32K_P if XTAL32K_N is left open. An external [0 – VH] square signal can be applied on the XTAL32K_P
pin with 1.1 V +/-10 %.
An external signal below 1.0 V or above 1.2 V cannot be applied.
LPC
XTAL32K_P XTAL32K_N
CX1 CX2
XTAL
Figure 5. Reference oscillator circuit
For best results, it is critical to select a matching crystal for the on-chip oscillator. Load Capacitance (CL), Series
Resistance (RS), and Drive Level (DL) are important parameters to consider while choosing the crystal. After
selecting the proper crystal, the external load capacitor CX1 and CX2 values can also be generally determined by
the following expression:
CX1 = CX2 = 2CL - (CPad + CParasitic + Ccapbank)
Where:
CL - Crystal load capacitance
CPad - Pad capacitance of the XTAL32K_P and XTAL32K_N pins (~3 pF).
CParasitic – Parasitic or stray capacitance of external circuit.
Ccapbank – Cap Bank
Although CParasitic can be ignored in general, the actual board layout and placement of external components
influences the optimal values of external load capacitors. Therefore, it is recommended to fine-tune the values
of external load capacitors on the actual hardware board to get the accurate clock frequency. For fine-tuning,
output the RTC Clock to one of the GPIOs and optimize the values of external load capacitors for minimum
frequency deviation.
AN13707 All information provided in this document is subject to legal disclaimers. © 2023 NXP B.V. All rights reserved.
Application note Rev. 1 — 4 September 2023
7 / 25
NXP Semiconductors AN13707
Hardware Design Guidelines for LPC553x/LPC55S3x Microcontrollers
4.4.1 RTC Printed Circuit Board (PCB) design guidelines
•Connect the crystal and external load capacitors on the PCB as close as possible to the oscillator input and
output pins of the chip.
•The length of traces in the oscillation circuit must be as short as possible and must not cross other signal
lines.
•Ensure that the load capacitors CX1, CX2, and CX3, in case of third overtone crystal usage, have a common
ground plane.
•Loops must be made as small as possible to minimize the noise coupled through the PCB and to keep the
parasitic as small as possible.
•Lay out the ground (GND) pattern under the crystal unit.
•Do not lay out other signal lines under the crystal unit for multi-layered PCB.
4.5 Common suggestions for the PCB layout of the oscillator circuit
The crystal oscillator is an analog circuit and must be designed carefully and according to the analog-board
layout rules, see Figure 6.
•Send the PCB to the crystal manufacturer to determine the negative oscillation margin as well as the optimum
value of CXTAL and CEXTAL capacitors. The data sheet includes recommendations for the tank capacitors
CXTAL and CEXTAL. These values together with the expected PCB, pin, and stray capacitors values must be
used as an initial point.
•The crystal or resonator oscillator is sensitive to stray capacitance and noise from other signals. It must be
placed away from high-frequency devices and traces to avoid and reduce the capacitive coupling between the
XTAL and EXTAL pins and their PCB traces.
•The main oscillation loop current is flowing between the crystal and the load capacitors. This signal path
(Oscillator to CEXTAL and CXTAL to Oscillator) must be kept as short and symmetric tracing as possible.
Therefore, both the capacitor's ground connections must always be closer to the VSS pin using the copper-
poured ground plane and there must be several vias to the internal ground layer in the PCB for efficient
grounding.
•Connect the EXTAL and XTAL pins to the required oscillator components only, and not to any other devices.
The following figure shows the recommended placement and routing for the oscillator layout.
Cooper pour
GROUND plane
GROUND via
GROUND
2nd layer
Crystal/
oscillator
All VSS pins should
be connected to
common GROUND
at the PCB level
VSS
XTAL
EXTAL
CXTAL
CEXTAL
Figure 6. Suggested crystal oscillator layout
AN13707 All information provided in this document is subject to legal disclaimers. © 2023 NXP B.V. All rights reserved.
Application note Rev. 1 — 4 September 2023
8 / 25
NXP Semiconductors AN13707
Hardware Design Guidelines for LPC553x/LPC55S3x Microcontrollers
5 Boot mode configuration
This section gives information about boot mode selection and configuration.
5.1 Boot mode selection
The internal ROM memory is used to store the boot code called boot ROM. After a reset, the Arm processor
starts its code execution from this memory. The boot ROM code is executed every time the part is powered-ON,
is reset, or wakes up from a deep power-down mode of low-power modes.
Images can be stored either in the internal flash as the LPC553x/S3x has an internal flash for code and data
storage or in the Serial NOR connected to the FLEXSPI controller. The code is then validated, and the boot
ROM vectors to on-chip flash or the off-chip FLASH. Depending on the values of the CMPA bits, ISP pin, and
the image header type definition, the bootloader decides whether to boot from the internal flash, off-chip flash,
or run into ISP mode. The LPC553x/S3x reads the status of the ISP pins to determine the boot source. See
Table 4.
Boot mode ISP1 (PIO0_7
pin)
ISP0 (PIO0_5
pin)
Description
Internal
Flash boot
LOW LOW The LPC553x looks for a valid image from the internal flash; if there is no
valid image, the LPC553x looks for a valid image in the recovery boot device
if recovery boot is enabled (4:0, word 1 in CMPA) in CMPA. If it still fails, the
LPC553x enters ISP boot mode based on DEFAULT_ISP_MODE bits.
ISP boot LOW HIGH One of the serial interfaces (UART0, I2C1, HS_SPI, USB0-FS, CAN) is used
to download the image from the host into the internal flash. The first valid
probe message on USART, I2C, SPI, CAN, or USB locks in that interface
FLEXSPI
boot
HIGH LOW The LPC553x looks for a valid image in the external flash; if there is no valid
image, the LPC553x looks for a valid image in the recovery boot device if
recovery boot is enabled (4:0, word 1 in CMPA) in CMPA. If it still fails, the
LPC553x enters ISP boot mode based on DEFAULT_ISP_MODE bits.
AUTO boot HIGH HIGH The LPC553x looks for a valid image in the internal flash; if there is no valid
image, the LPC553x looks for a valid image in the external NOR flash; if no
valid image, the LPC553x looks for a valid image in the recovery boot device
if recovery boot is enabled d (4:0, word 1 in CMPA) in CMPA. If it still fails,
the LPC553x enters ISP boot mode based on DEFAULT_ISP_MODE bits.
Table 4. Boot mode and ISP download modes based on ISP pins
Table 5 shows the ISP pin assignments and is the default pin assignment used by the Boot ROM that cannot be
changed.
ISP pin Port pin assignment
ISP0 PIO0_5
ISP1 PIO0_7
USART_ISP mode
FC0_TXD PIO0_30
FC0_RXD PIO0_29
I2C_ISP mode
FC1_SDA PIO0_13
FC1_SCL PIO0_14
Table 5. ISP pin assignment
AN13707 All information provided in this document is subject to legal disclaimers. © 2023 NXP B.V. All rights reserved.
Application note Rev. 1 — 4 September 2023
9 / 25
NXP Semiconductors AN13707
Hardware Design Guidelines for LPC553x/LPC55S3x Microcontrollers
ISP pin Port pin assignment
SPI Flash Recovery mode
FC0_TXD_SCL_MISO_WS PIO0_30
FC0_RXD_SDA_MOSI_DATA PIO0_24
FC0_CTS_SDA_SSELN0 PIO0_31
FC0_SCK PIO0_28
HS_SPI_SCK PIO1_2
HS_SPI_SSEL1 PIO1_1
HS_SPI_MISO PIO1_3
HS_SPI_MOSI PIO0_26
FC3_TXD_SCL_MISO_WS PIO0_2
FC3_RXD_SDA_MOSI_DATA PIO0_3
FC3_CTS_SDA_SSELN0 PIO0_4
FC3_SCK PIO0_6
SPI ISP mode
HS_SPI_SCK PIO1_2
HS_SPI_SSEL1 PIO1_1
HS_SPI_MISO PIO1_3
HS_SPI_MOSI PIO0_26
USB0-FS ISP mode
USB0_VBUS PIO1_31(if [bit_22] @0x3FC14 is set to 1, use P0_22)
USB0_DP Dedicated pin per package
USB0_DM Dedicated pin per package
CAN ISP mode
CAN_TXD PIO0_30
CAN_RXD PIO1_22
FlexSPI Pins
FLEXSPI_SSEL PIO0_21
FLEXSPI_CLK PIO0_19
FLEXSPI_DQS PIO0_25
FLEXSPI_CLK_N PIO0_22
FLEXSPI_D0 PIO0_6
FLEXSPI_D1 PIO0_4
FLEXSPI_D2 PIO0_3
FLEXSPI_D3 PIO0_2
FLEXSPI_D4 PIO1_16
FLEXSPI_D5 PIO1_15
Table 5. ISP pin assignment...continued
AN13707 All information provided in this document is subject to legal disclaimers. © 2023 NXP B.V. All rights reserved.
Application note Rev. 1 — 4 September 2023
10 / 25
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere NXP Semiconductors Mikrocontroller Handbücher
NXP Semiconductors
NXP Semiconductors LPC824M201JHI33 Bedienungsanleitung
NXP Semiconductors
NXP Semiconductors ASUG Bedienungsanleitung
NXP Semiconductors
NXP Semiconductors LPC1768 Bedienungsanleitung
NXP Semiconductors
NXP Semiconductors SLN-VIZN3D-IOT Bedienungsanleitung
NXP Semiconductors
NXP Semiconductors QN9020 mini DK Bedienungsanleitung
NXP Semiconductors
NXP Semiconductors P89LPC952 Bedienungsanleitung
NXP Semiconductors
NXP Semiconductors MPC5746R Leitfaden
NXP Semiconductors
NXP Semiconductors MPC5606BK Bedienungsanleitung
NXP Semiconductors
NXP Semiconductors WPR1500-BUCK Bedienungsanleitung
NXP Semiconductors
NXP Semiconductors LPC5410x Bedienungsanleitung
NXP Semiconductors
NXP Semiconductors MPC5777M Benutzerhandbuch
NXP Semiconductors
NXP Semiconductors freescale semiconductor CSM12D Bedienungsanleitung
NXP Semiconductors
NXP Semiconductors UM11579 Bedienungsanleitung
NXP Semiconductors
NXP Semiconductors LPC11E Series Bedienungsanleitung
NXP Semiconductors
NXP Semiconductors JN517x-DK005 Bedienungsanleitung
NXP Semiconductors
NXP Semiconductors Freescale K22 Bedienungsanleitung
NXP Semiconductors
NXP Semiconductors MCIMX6UL-EVK Bedienungsanleitung
NXP Semiconductors
NXP Semiconductors FRDM665SPIEVB Bedienungsanleitung
NXP Semiconductors
NXP Semiconductors freescale KV4 Series Bedienungsanleitung
NXP Semiconductors
NXP Semiconductors SLN-LOCAL2-IOT Bedienungsanleitung
NXP Semiconductors
NXP Semiconductors SLN-LOCAL2-IOT Bedienungsanleitung
NXP Semiconductors
NXP Semiconductors MPC5777M Bedienungsanleitung
NXP Semiconductors
NXP Semiconductors S12 MagniV MC9S12ZVML128 Bedienungsanleitung
NXP Semiconductors
NXP Semiconductors Freescale Flexis MCF51MM256 Bedienungsanleitung
Beliebte Mikrocontroller Handbücher anderer Marken
AMS
AMS AS7261 Demo Kit Bedienungsanleitung
Novatek
Novatek NT6861 Bedienungsanleitung
Espressif Systems
Espressif Systems ESP8266 SDK Einrichtungshandbuch
Nuvoton
Nuvoton ISD61S00 ChipCorder Leitfaden
STMicrolectronics
STMicrolectronics ST7 Assembler Linker Bedienungsanleitung
Texas Instruments
Texas Instruments Chipcon CC2420DK Bedienungsanleitung
Lantronix
Lantronix Intrinsyc Open-Q 865XR SOM Bedienungsanleitung
NEC
NEC 78GK0S/K 1+ Series Montage- und Bedienungsanleitung
Mikroe
Mikroe SEMITECH N-PLC Click Montage- und Bedienungsanleitung
Intel
Intel Agilex Bedienungsanleitung
Cypress
Cypress CY4607 HX2VL Bedienungsanleitung
DIGITAL-LOGIC
DIGITAL-LOGIC MICROSPACE Bedienungsanleitung
Texas Instruments
Texas Instruments TMS320F2837 D Series Bedienungsanleitung
CYPRES
CYPRES CY14NVSRAMKIT-001 Bedienungsanleitung
Texas Instruments
Texas Instruments INA-DUAL-2AMP-EVM Bedienungsanleitung
Espressif Systems
Espressif Systems ESP8266EX Betriebsanleitung
Abov
Abov AC33M8128L Bedienungsanleitung
Laird
Laird BL654PA Bedienungsanleitung