OBID ID RW01L.AB-A Bedienungsanleitung

MANUAL

final

public (B)

2006-01-12

H20801-1e-ID-B.doc

DATEINAMEFORMATVERBINDEN

OBID

ID RW01L.AB-A

Firmware version AB100 and higher

OBID®Manual ID RW01L.AB-A

FEIG ELECTRONIC GmbH Page 2 of 39 H20801-1e-ID-B.doc

Note

FEIG ELECTRONIC GmbH

Lange Strasse 4

D-35781 Weilburg-Waldhausen

Tel.: +49 6471 3109-0

http://www.feig.de

Edition: MD/06/01/12 - h20801-1e-id-b.doc

With the edition of this manual, all previous editions become void. Indications made in this manual may be changed without

previous notice.

Copying of this document, and giving it to others and the use or communication of the contents thereof are forbidden without

express authority. Offenders are liable to the payment of damages. All rights are reserved in the event of the grant of a patent

or the registration of a utility model or design.

Composition of the information in this manual has been done to the best of our knowledge. FEIG ELECTRONIC GmbH does

not guarantee the correctness and completeness of the details given in this manual and may not be held liable for damages

ensuing from incorrect or incomplete information. Since, despite all our efforts, errors may not be completely avoided, we are

always grateful for your useful tips.

The installation instructions given in this manual are based on advantageous boundary conditions. FEIG ELECTRONIC

GmbH does not give any guarantee promise for perfect function in cross environments.

FEIG ELECTRONIC GmbH assumes no responsibility for the use of any information contained in this manual and makes no

representation that they free of patent infringement. FEIG ELECTRONIC GmbH does not convey any license under its patent

rights nor the rights of others.

OBID®is a registered trademarks of FEIG ELECTRONIC GmbH.

hitagTM is a registered trademark of Philips Electronics N.V.

General information's regarding this manual

•The sign ")" indicates extensions or changes of this manual compared with the former issue.

•If bits within one byte are filled with "-", these bit spaces are reserved for future extensions or for internal

testing- and manufacturing-functions. These bit spaces must not be changed, as this may cause faulty op-

eration of the Reader.

•The following figure formats are used:

0...9: for decimal figures

0x00...0xFF: for hexadecimal figures,

b0...1 for binary figures.

•The hexadecimal value in brackets "[ ]" marks a control byte (command).

OBID®Manual ID RW01L.AB-A

FEIG ELECTRONIC GmbH Page 3 of 39 H20801-1e-ID-B.doc

Contents:

1. Introduction 5

1.1. Principles of operation of the OBID®-System...................................................................5

1.2. The OBID®ID RW01L.AB-A ................................................................................................5

1.3. Technical data.....................................................................................................................6

1.4. Dimensions..........................................................................................................................7

1.5. Pin configuration.................................................................................................................8

1.6. Toggling Polling- / Scan-Mode...........................................................................................8

1.7. Connecting an external antenna........................................................................................9

1.8. Declaration of Conformity................................................................................................10

2. Data traffic between Reader and Host 11

2.1. Asynchronous interface, data formats and protocol frames........................................12

2.2. Polling mode......................................................................................................................14

2.3. Scan mode.........................................................................................................................15

2.3.1. Scan mode over the asynchronous interface..............................................................16

2.3.2. Scan mode over the data/clock interface ....................................................................17

3. Polling mode (read and write transponder data) 20

3.1. [0x11] GET_SNR................................................................................................................20

3.2. [0x14] WRITE_DB (Write data block(s)) ..........................................................................21

3.3. [0x15] READ_DB (Read data block(s) .............................................................................22

3.4. [0x1A] Halt (ID DTx.B only)...............................................................................................23

4. Commands for reader control and configuration 24

4.1. [0x62] CONFIG_READ.......................................................................................................24

4.2. [0x82] CONFIG_WRITE.....................................................................................................24

4.3. [0x64] CONFIG_RESET.....................................................................................................25

OBID®Manual ID RW01L.AB-A

FEIG ELECTRONIC GmbH Page 4 of 39 H20801-1e-ID-B.doc

4.4. [0x63] CPU_RESET...........................................................................................................25

4.5. [0x65] GET_VERSION.......................................................................................................26

4.6. [0x69] RF_RESET..............................................................................................................27

4.7. [0x52] BAUDRATE_DETECTION......................................................................................28

5. Reader Configuration 29

5.1. CFG0: Reader Parameters................................................................................................29

5.1.1. COM_PARA ................................................................................................................30

5.1.2. READER_MODE.........................................................................................................31

5.1.3. SCAN_MODE..............................................................................................................32

5.1.4. DB_ADR......................................................................................................................34

5.1.5. D_LGT.........................................................................................................................34

5.1.6. D_START....................................................................................................................35

5.1.7. SCAN_PREFIX............................................................................................................35

5.1.8. SCAN_TERM ..............................................................................................................35

5.1.9. TAG_DRV....................................................................................................................35

APPENDIX 36

APPENDIX A: Timing................................................................................................................36

APPENDIX B: List of status bytes ...........................................................................................37

APPENDIX C: Memory model ID DTx.B...................................................................................38

APPENDIX C1: Philips Hitag 1...............................................................................................38

APPENDIX C2: Philips Hitag S ..............................................................................................39

OBID®Manual ID RW01L.AB-A

FEIG ELECTRONIC GmbH Page 5 of 39 H20801-1e-ID-B.doc

1. Introduction

1.1. Principles of operation of the OBID®-System

The OBID® Identification System is an inductive transmission system for non-contact identification

(ID) of objects. Use of the components in the read/write system makes it possible to read and write

passive transponders. This system consists of a reader, antenna and a transponder as storage

medium for the data.

When a transponder enters the local magnetic field of the antenna, it is supplied with energy and can

be written to or read. The received data are received by the same reader antenna which generates the

magnetic field and sends the data to the transponder.

The magnetic field and the send and received transponder data can penetrate all non-conducting

materials, so that even hidden reading and writing is possible.

1.2. The OBID®ID RW01L.AB-A

The OBID®ID RW01L.AB-A reader is designed for typical applications involving personnel

identification, access control, time tracking, billing systems, etc.

It features multi-tag capability. This means it can:

•read read-only data carriers (OBID®ID CTx.A)

e.g. H4001, H4002, H4022, H4102, etc. from EM Microelectronics and

Unique from SOKYMAT as well as

•read/write transponders (OBID®ID DTx.B)

HITAG 1 and HITAG S from Philips Semiconductors.

The reader has a bi-directional, asynchronous interface (RS232-TTL) and a unidirectional data/clock

interface which can run in Wiegand or magnetic card reader emulation. The emulation modes of the

data/clock interface ensures easy conversion from traditional identification readers to the OBID®ID

RW01L.AB-A.

The OBID®ID RW01L.AB-A can be easily software-configured for any application.

The OBID®ID RW01L.AB-A offers access to the entire physical memory range of the supported

transponders (see: 3.2. [0x14] WRITE_DB (Write data block(s)) / 3.3. [0x15] READ_DB (Read data

block(s)

OBID®Manual ID RW01L.AB-A

FEIG ELECTRONIC GmbH Page 6 of 39 H20801-1e-ID-B.doc

1.3. Technical data

Circuit board dimensions (W x H x D) 45mm x 40mm x 16mm +/- 1mm

Connection 2 x 10-pin connector on the solder side

(pins: 0.7x0.7/ long incl. approx. 8mm insulator

Temperature range (operating and storage) -20°C to +70°C

Supply voltage 5V DC±5 %

Current consumption ca. 40 mA

Operating frequency 125 kHz

Antenna Integrated (mounted on circuit board)

Supported transponders •read-only:

- ID CTx.A

- H4001, H4002, H4022, H4102,

- Unique

- Q5, e5555 (plain manchester 64 Bit

read-only mode)

•read/write

- ID DTx.B

- Hitag 1

- Hitag S

Reading Range with ISO transponder card1•ca. 80 mm

Interfaces •RS232-TTL

•Data / Clock

- Magnetic card emulation

(to (ISO 7811 Track1 or Track2)

- Wiegand Emulation

Functions •Polling mode (over RS232-TTL)

Reading and writing transponder data

•Scan mode (over RS232-TTL and Data / Clock)

Autonomous reading of transponder data

Applicable Norms

European RF Approval EN 300 330

EMC EN 300 683

1Depending on the antenna size and Q-factor of the antenna in the transponder

OBID®Manual ID RW01L.AB-A

FEIG ELECTRONIC GmbH Page 7 of 39 H20801-1e-ID-B.doc

1.4. Dimensions

Fig. 1: Dimensions (mm)

40,0

+0,5

-0,5

2,5

8,0

+0,5

-0,5

45,0

+0,5

-0,5

2,54

8,0

+0,5

-0,5

B2 B1

32,4

+0,1

-0,1

33,0

+0,1

-0,1

OBID®Manual ID RW01L.AB-A

FEIG ELECTRONIC GmbH Page 8 of 39 H20801-1e-ID-B.doc

1.5. Pin configuration

Terminal Pin Name Function

1 /CLS Data/clock interface: valid data

2ANT1

3ANT2

External antenna

4 NC - Not connected -

5 /RCP Data/clock interface: clock output

6 /RDP Data/clock interface: data output

7 TxD RS232-TTL TxD

8 RxD RS232-TTL RxD

9 NC - Not connected -

10 NC - Not connected -

1/RST

Reset input (active to GND ⇒Reset)

2 NC. - Not connected -

3 GND Ground (0 V)

4 VCC Supply voltage (+5V)

1MOD1

Toggling Polling-Mode / Scan-Mode

MOD1 = open ⇒Polling-Mode

MOD1 = closed (GND) ⇒Scan-Mode

2 NC - Not connected -

3 NC - Not connected -

4 NC - Not connected -

5 NC - Not connected -

6 NC - Not connected -

1.6. Toggling Polling- / Scan-Mode

There are two ways to toggle between polling and scan mode.

•By soldering a 0 Ωresistor in B1 (see: 1.3. Technical data) scan mode is permanently activated.

•To temporarily activate scan mode, you can tie input MOD1 to potential GND (X2 / Pin 3).

The following table shows the possible configurations.

B1 MOD1

Closed X

Scan-Mode Open GND

Polling-Mode Open Open

OBID®Manual ID RW01L.AB-A

FEIG ELECTRONIC GmbH Page 9 of 39 H20801-1e-ID-B.doc

1.7. Connecting an external antenna

In place of the antenna on the ID RW01L.AB-A, you may connect an external antenna to terminals

ANT1 and ANT2 (X1). When connecting an external antenna, you must separate the two connections

on the onboard antenna.

Note the following when dimensioning and tuning the antenna.

Antenna parameters

- Recommended max. dimensions 70 x 70 mm

- Antenna coil material : Lacquered copper wire

- Antenna coil wire thickness: 0.2 mm

- Inductance: 737 ±7 µH

- Resistance: 10 ±1 Ω

- Intrinsic capacitance < 120 pF

Test points:

ANT2 Antenna signal:

GND Reference potential

Fig. 2: Antenna signal between ANT2 and GND

Test values

Upp: 10 V

f: 125 kHz

NOTE:

The reader is designed for operating only one antenna. Operating 2 parallel switched antennas

may damage the reader, or at least have a negative impact on the read range of the reader.

OBID®Manual ID RW01L.AB-A

FEIG ELECTRONIC GmbH Page 10 of 39 H20801-1e-ID-B.doc

1.8. Declaration of Conformity

Inhaltsverzeichnis

Andere OBID Andere Handbücher

OBID

OBID CPR50.10-E Bedienungsanleitung

Beliebte Andere Handbücher anderer Marken

GO Industries

GO Industries 38017 Bedienungsanleitung

Cissell

Cissell 30LBCMAN2 Bedienungsanleitung

RIDGID

RIDGID K-60SP Bedienungsanleitung

Gage Bilt

Gage Bilt GB751SH-5 Bedienungsanleitung

OVE

OVE SIERRA 60 Bedienungsanleitung

ReelCraft

ReelCraft 7800 OLB21 Bedienungsanleitung

Body Armor 4x4

Body Armor 4x4 ECO-SERIES Bedienungsanleitung

ROBLIN

ROBLIN DROP Benutzerhandbuch

EMG

EMG EMG-ACB BARREL Service-Handbuch

MiniSolar

MiniSolar MT-150 Bedienungsanleitung

Parkside

Parkside PSZ 250 B2 Bedienungsanleitung

ABB

ABB REM 610 Produkthandbuch

Parkside

Parkside 55992 Betriebsanleitung

Skyjacker

Skyjacker F250 Bedienungsanleitung

IBM

IBM IBM SYSTEM Z Installationsanleitung

Grech Motors

Grech Motors G28 Bedienungsanleitung

NOVAK

NOVAK BATTERY CARE SHEET Leitfaden

Telemotive

Telemotive blue PiraT Mini Benutzerhandbuch