OHAUS D52 Bedienungsanleitung

D52 Indicator

RS232/RS485/USB Option

Instruction Manual

Interfaz RS232/RS485/USB

Manual de instrucciones

Interface RS232/RS485/USB

Manuel d’instruction

RS232/RS485/USB Schnittstelle

Bedienungsanleitung

Interfaccia USB/RS232/RS485

Manuale di Istruzioni

USB/RS232/RS485 折

折ↅ

∎䞷広㢝󱂖

EN-1

INTRODUCTION

This RS232/RS485/USB interface kit is for use with the Defender®5000 TD52 indicators

and D52 scales.

KIT CONTENT

INTERFACE INSTALLATION

Install the RS232 / RS485 / USB Device Interface on the underside of the indicator as

shown.

For TD52P:

1. Separate the terminal from the base by loosening load cell cable male connector.

Remove the interface option cover.

Load cell cable male connector

Interface option cover

EN-2

2. Break off the rib of the interface option cover as shown.

3. Connect the cable to the main board connector as shown. Place the ferrite in the

groove of the rear housing.

4. Install the RS232/RS485/USB Device board. Secure it with the 2 screws.

Connect the cable to the accessory board 12 pin connector.

Rib

Ferrite

Main board

connector 2

Cable

12 Pin Connector

Screw

EN-3

5. Set the function switch to according to the desired function.

Connect the corresponding RS232, RS485 or USB device cable to the applicable

connector.

Refer to Table 1 in the Setup section for the function switch settings.

Refer to Table 2 in the Setup section for RS232RS485 connection for external

serial devices.

6. Fix the output cable with the nylon cable tie.

7. Put the interface option cover back on the terminal.

Function switch

USB Device Socket

RS232/RS485 Connector

Nylon cable tie

Output cable

EN-4

For TD52XW:

1. Separate the terminal from the base by loosening load cell cable female

connector. Remove the interface option cover.

2. Take the rear housing down from the front housing as shown.

screws

Load cell cable male

connector

M25 hole plug

EN-5

3. Connect the cable to the main board connector. Place the ferrite in the slot of the

internal cover as shown.

4. Install the RS232 / RS 485 / USB device board. Secure it with 2 screws

(Note: boss post is 5 and 7). Connect the cable to RS232 / 485 / USB device

board 12 pin connectors.

Cable

Ferrite

Main board connector 2

Boss Post 5, 7

EN-6

5. Pass the RS232 / RS485 / USB device output cable through the cap nut; then

spread the rubber seal and place it over the cable. Now pass the cable through

the body of the cable gland.

12Pin Connector

Function switch

RS232/RS485

connector

screw

RS232 / RS485

Output

M25 Cable Gland

Cap nut

USB Device

Output Cable

M25 Cable Gland

Cap nut

EN-7

6. Toggle the Function switch according to different function. Put the corresponding

RS232 cable, RS485 cable or USB Device cable through the M25 hole. Connect

it to the applicable connectors.

7. Put the rear housing back on the front housing. Re-install the 6 screws.

8. Fasten the M25 gland to the rear housing.

RS232 cable / RS485 cable

USB Device cable

Current loop cable

M25 gland

EN-8

9. Push the rubber seal into the M25 cable gland.

10. Fasten the cap nut of the M25 gland.

For TD52XW with reversed rear cover:

1. Separate the terminal from the base by loosening load cell cable female

connector. Remove the interface option cover.

Rubber seal

Cap nut of M25 gland

Screw

M25 hole plug

Load cell cable male connector

Inhaltsverzeichnis

Sprachen:

Andere OHAUS Messgerät Handbücher

OHAUS

OHAUS a-AB33M1 Bedienungsanleitung

OHAUS

OHAUS STARTER 2200 Bedienungsanleitung

OHAUS

OHAUS ST20C-A Bedienungsanleitung

OHAUS

OHAUS MB45 Bedienungsanleitung

OHAUS

OHAUS AB23PH Bedienungsanleitung

OHAUS

OHAUS STARTER 3100M Bedienungsanleitung

OHAUS

OHAUS TD52 Bedienungsanleitung

OHAUS

OHAUS ST300 Bedienungsanleitung

OHAUS

OHAUS Defender I-D33P15B1R1 Bedienungsanleitung

OHAUS

OHAUS ST400D-B Bedienungsanleitung

OHAUS

OHAUS CKW Gebrauchs- und Pflegehandbuch

OHAUS

OHAUS STARTER 5000 Bedienungsanleitung

OHAUS

OHAUS ST20M Series Bedienungsanleitung

OHAUS

OHAUS MB90 Bedienungsanleitung

OHAUS

OHAUS Ranger 3000 Series Bedienungsanleitung

OHAUS

OHAUS ST3100M-B Bedienungsanleitung

OHAUS

OHAUS Defender 2000 Series Bedienungsanleitung

OHAUS

OHAUS MB90 Bedienungsanleitung

OHAUS

OHAUS T51 Gebrauchs- und Pflegehandbuch

OHAUS

OHAUS MB90 Bedienungsanleitung

OHAUS

OHAUS ST20D Bedienungsanleitung

OHAUS

OHAUS MB45 Bedienungsanleitung

OHAUS

OHAUS starter 3100 Bedienungsanleitung

OHAUS

OHAUS CKW-55 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung