OHAUS I-DT33XW Bedienungsanleitung

i-DT33P / i-DT33XW Indicator

USB Option

Instruction Manual

Indicador i-DT33P / i-DT33XW

Opción USB

Manual de Instrucciones

Indicateur i-DT33P / i-DT33XW

Option USB

Mode d’emploi

Anzeigegerät i-DT33P oder i-DT33XW

USB-Option

Bedienungsanleitung

Indicatore i-DT33P / i-DT33XW

Opzione USB

Manuale di istruzioni

i-DT33P / i-DT33XW Indicator

USB Option

사용자 매뉴얼

D3000 シリーズ

（i-DT33P / i-DT33XW）

USB オプション

取扱説明書

i-DT33P / i-DT33XW 仪表

USB 选件

使用说明书

EN-1

INTRODUCTION

This USB interface kit is for use with the Defender®3000 i-DT33P and i-DT33XW

indicators.

KIT CONTENTS

CAUTION: THE INSTALLATION AND CONNECTIONS SHOULD

ONLY BE DONE BY AUTHORIZED AND QUALIFIED PERSONNEL,

SUCH AS AN ELECTRICIAN.

Cable

USB Board

Screws (2)

Watertight

Seal (with Two

Holes)

USB Cable

EN-2

INTERFACE INSTALLATION

Install the USB Interface kit to the indicator as the following.

WARNING: BEFORE INSTALLATION, POWER OFF THE

INDICATOR AND REMOVE ALL EXTERNAL AC POWER

CONNECTIONS.

i-DT33P

1. Remove the battery cover in the direction of the arrow, and take out dry

batteries if used.

2. Slightly push the end of the charging cover (circled) in the direction of the

arrow and take it out.

EN-3

3. Remove the sealing plug upwards.

4. Take out the cable supplied. Connect one side to the main board connector

(circled), and pass the other side through the side hole.

EN-4

5. Take out the USB board supplied. Connect the cable's another side to the

connector on the USB board (circled). Then insert the USB board into the two

card slots (circled) on both sides.

6. Take out the USB cable supplied and pass it through the hole where the

sealing plug is removed (circled), and then connect its USB interface to the

connector on the USB board (circled).

USB board

EN-5

7. Re-install the dry batteries if used, and close the battery cover.

i-DT33XW

1. Remove the six hex head bolts from the rear housing of the indicator.

EN-6

2. Release the strain relief for option connector (circled) including the watertight

seal in it on the bottom of the indicator and remove the plug at the end of it.

3. Take out the cable and the USB board supplied and pin the upper left corner

and the lower right corner of the board on the positioning column (circled),

facing up.

Watertight Seal（with One Hole）

Plug

EN-7

4. Connect one side of the cable to the connector on the USB board (circled) and

the other to the indicator's main board connector (circled).

5. Screw the two screws to the indicator's screw holes (circled). Make sure the

USB board is tightly clamped by the screws.

EN-8

6. Take out the USB cable supplied and pass it through the strain relief for option

connector. Make sure the watertight seal is attached to it, and then connect its

USB interface to the connector on the USB board (circled).

Note: If you install RS232 and the USB kit at the same time, please use the

supplied watertight seal with two holes. Pass the RS232 cable through one hole of

the watertight seal and the Ethernet cable through another.

Strain Relief for Option Connector

Watertight Seal (with One Hole)

Watertight Seal （with Two Holes）

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere OHAUS Messgerät Handbücher

OHAUS

OHAUS TD32PE Bedienungsanleitung

OHAUS

OHAUS ST20C-A Bedienungsanleitung

OHAUS

OHAUS MB90 Bedienungsanleitung

OHAUS

OHAUS MB35 Bedienungsanleitung

OHAUS

OHAUS D52 Bedienungsanleitung

OHAUS

OHAUS ST20D Bedienungsanleitung

OHAUS

OHAUS CD-1 Bedienungsanleitung

OHAUS

OHAUS MB35 Bedienungsanleitung

OHAUS

OHAUS TD52P Bedienungsanleitung

OHAUS

OHAUS TD52 Bedienungsanleitung

OHAUS

OHAUS STARTER 2100 Bedienungsanleitung

OHAUS

OHAUS MB23 Bedienungsanleitung

OHAUS

OHAUS STARTER 300C Bedienungsanleitung

OHAUS

OHAUS MB90 Bedienungsanleitung

OHAUS

OHAUS Ranger 3000 Series Bedienungsanleitung

OHAUS

OHAUS Ranger 3000 Series Bedienungsanleitung

OHAUS

OHAUS i-DT61XWE Bedienungsanleitung

OHAUS

OHAUS STARTER 400D Bedienungsanleitung

OHAUS

OHAUS i-DT33P Bedienungsanleitung

OHAUS

OHAUS T31P Bedienungsanleitung

OHAUS

OHAUS ST300-B Bedienungsanleitung

OHAUS

OHAUS a-AP30TUR Bedienungsanleitung

OHAUS

OHAUS ST3100M-B Bedienungsanleitung

OHAUS

OHAUS CKW-55 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

OHAUS i-DT33XW Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken