Olympus U-PCD2 Bedienungsanleitung

A X 7 3 5 7

INSTRUCTIONS

U-PCD2

Phase Contrast Condenser

This instruction manual is for use of the Olympus Phase Contrast Condenser Model U-PCD2. To ensure the

safety and obtain optimum performance and to familiarize yourself fully with the use of this unit, we recom-

mend that you study this manual thoroughly before operating the microscope. Retain this instruction manual

in an easily accessible place near the work desk for future reference.

BEFORE USE

This unit employs the UIS2/UIS optical system and should be used only with UIS2/UIS microscopes,

eyepieces and objectives. Less than optimum performance may result if inappropriate accessories

are used.

Caution:

If the condenser is used in a manner not specified by this manual, the safety of the unit may be impaired.

In addition, the unit may also be damaged. Always use the unit as outlined in this instruction manual.

FEATURES

1. 3 kinds of the light annuli are built into this turret condenser, allowing the following observations by

changing the light annuli.

Phase contrast observation: 10X, 20X, 40X, 100X

Darkfield observation: 10X or higher

Brightfield observation

2. This phase contrast condenser makes it possible to center each light annuli.

3. Applicable phase contrast objectives are as follows:

UIS2 series UPlanFLN 10Xph, 20Xph, 40Xph, 100XOph

PlanN 10Xph, 20Xph, 40Xph, 100XOph

UIS series UPlanFl 10Xph, 20Xph, 40Xph, 100XOph

Ach 10Xph, 20Xph, 40Xph, 100XOph

Plan 10Xph, 20Xph, 40Xph, 100XOph

U-PCD2

NOMENCLATURE

Phase Contrast Turret Condenser

Aperture iris diaphragm lever

Light annulus centering knob

Phase contrast turret Mounting dovetail

Aperture is wide-open ex-

cept when this is set at the

brightfield position.

Fig. 1

ASSEMBLY

Mounting on the Microscope

1. Rotate the coarse adjustment knob @ to fully raise the stage.

#Be careful not to raise the stage too much to avoid acci-

dental contact with the objective lens and specimen.

2. Lower the condenser holder with the condenser height ad-

justment knob ² until it stops at the lower limit.

3. Loosen the condenser clamping knob ³.

4. Insert the phase contrast turret condenser into the dovetail

guideway of the condenser holder until the positioning pin of

the condenser is engaged in the positioning groove of the

mounting dovetail guideway.

5. Tighten the clamping knob of the condenser holder.

6. Raise the condenser holder until it stops at the upper limit.

U-PCD2

OPERATION

Center the Phase Contrast Condenser

1. Rotate the phase contrast turret until the letter “0” can be seen in the central window, and open the

aperture iris diaphragm fully.

2. Place a specimen on the stage, bring the 10X objective into the light path and focus on the specimen.

3. Reduce the field iris diaphragm of the microscope frame.

4. While looking through the eyepieces, move the condenser up and down with the condenser height

adjustment to focus on the image of the field iris diaphragm.

5. Adjust the condenser centering knobs | to bring the diaphragm image into the center of the field of view.

(Figs 1 & 2)

· Widening the diameter of the field iris diaphragm progressively, repeat this operation until the reduced

image of the diaphragm becomes inscribed in the circle which indicates the field of view.

· When opening the field iris diaphragm, the image may be out of focus. Re-focus with the condenser

height adjustment knob.

Fig. 2

Phase Contrast Observation

1. Swing the objective of your choice into the light path.

2. Rotate the phase contrast turret until the turret index dot indicates the Ph number seen through the

central window which corresponds to the Ph number indicated on the side of objective lens.

3. Focus roughly on the specimen.

4. Remove one of the eyepieces, and insert the centering telescope U-CT30 into the eyepiece sleeve.

5. Rotate the top lens assembly of the U-CT30 to bring the bright ring (light annulus in the condenser) and

the dark ring (phase annulus in the objective) in focus.

6. Rotate the two light annulus centering knobs @ of the condenser until the light annulus and phase

annuls are concentric and superimposed. (Fig. 3)

Before centration After centration

a = b = c = d

Fig. 3

U-PCD2

# The other phase annuluses should be centered in the same manner.

In case Ph1 is indicated on both 10X and 20X objectives, for observation purposes, once the phase

annulus is aligned for 10X, it’s unnecessary to realign the phase annulus for 20X.

However, for the purpose of photomicrography, it is recommended the phase annulus be aligned for

each objective even though the same Ph number may be indicated on the objective lens.

7. Remove the U-CT30, and insert the eyepiece back into the eyepiece sleeve.

Now you can start your phase contrast observation with any phase contrast objective and corresponding

light annulus as desired.

Darkfield Observation

1. Rotate the turret until “DF” can be seen in the central window.

2. Engage the 10X or higher objective.

#Objectives with NA 0.7 or lower NA and objectives with iris diaphragm can be used.

3. Place the specimen on the stage and move the stage up and down to bring the specimen into focus.

4. Move the condenser up and down until uniform darkfield illumination is attained.

5. Open the field iris diaphragm to the extent that even brightness is attained.

#Keep eyes away from the eyepieces while changing the objective during darkfield observation, or

changing from darkfield to another observation mode.

2-43-2, Hatagaya, Shibuya-ku, Tokyo, Japan

Postfach 10 49 08, 20034, Hamburg, Germany

2 Corporate Center Drive, Melville, NY 11747-3157, U.S.A.

491B River Valley Road, #12-01/04 Valley Point Office Tower, Singapore 248373

2-8 Honduras Street, London EC1Y OTX, United Kingdom.

31 Gilby Road, Mt. Waverley, VIC 3149, Melbourne, Australia.

6100 Blue Lagoon Drive, Suite 390 Miami, FL 33126-2087, U.S.A.

This publication is printed on recycled paper.

Printed in Japan 2004 09 M 005–@

Inhaltsverzeichnis

Andere Olympus Laborausrüstung Handbücher

Olympus

Olympus SZ2-ILLC Bedienungsanleitung

Olympus

Olympus SZX2-ILLT Bedienungsanleitung

Olympus

Olympus SZX2 Series Bedienungsanleitung

Olympus

Olympus MX61A Bedienungsanleitung

Olympus

Olympus U-LH50HG Bedienungsanleitung

Olympus

Olympus AL120-12 Series Bedienungsanleitung

Olympus

Olympus U-RFLT50 Bedienungsanleitung

Olympus

Olympus OMCL-TR800PSA Bedienungsanleitung

Olympus

Olympus OER-Elite Bedienungsanleitung

Olympus

Olympus OER-Pro Bedienungsanleitung

Olympus

Olympus R1 Bedienungsanleitung

Olympus

Olympus SZX-RFL2 Bedienungsanleitung

Olympus

Olympus U-DO3 Bedienungsanleitung

Olympus

Olympus OMCL-AC160TS-W2 Bedienungsanleitung

Olympus

Olympus U-SRG Bedienungsanleitung

Olympus

Olympus SZX-DO Bedienungsanleitung

Olympus

Olympus U-HGLGPS Bedienungsanleitung

Olympus

Olympus CIX100 Bedienungsanleitung

Olympus

Olympus CX-DO Bedienungsanleitung

Olympus

Olympus SZ2-STS Bedienungsanleitung

Olympus

Olympus SZX-RFL3 Bedienungsanleitung

Olympus

Olympus SZX-SDO2 Bedienungsanleitung

Olympus

Olympus VISERA CLV-S40 Bedienungsanleitung

Olympus

Olympus SZX2-ILR66 Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung