Olympus ORBEYE OME-V200 Bedienungsanleitung

– 1 –

This guide is for quick reference only, especially for inspection and troubleshooting. Please refer to the instructions

provided with the device for detailed instructions.

1.1 Movement and lock of the equipment

1.3 Connection of the monitor

Holding the movement handles of this instrument

firmly. Check the position of the brake pedal, push up

it with a foot to unlock the casters.

After stopping this instrument, check the position of

the brake pedal, push it until it hits the back, apply

the brake, and confirm that this instrument is locked

to the floor.

1.2 Connection of the power cord

Connect the power plug of the power cord directly into the hospital grade wall mains outlet.

Connection of LMD-X550ST, LMD-X310ST, LMD-X550S, or LMD-X310S

The methods of connection of this instrument to the LMD-X550ST, LMD-X310ST, LMD-X550S, and

LMD-X310S are completely identical. The following instructions take the connection of the LMD-X550ST as

an example.

OME-V200 Quick Reference Guide

1 Installation and Connection

Brake pedal

Unlock Lock

Brake pedal

LMD-X550ST

MAJ-2309

SDI1 input terminals A – D

A BcD

SDI

SDI 2

→ → → → →

→ → →

→

(Red)

3G-SDI quad-link

combined output 1 or 2

terminal

OME-V200

(Green)

(Blue)

(White)

– 2 –

1.4 Connection of the video recorder

Connection of HVO-4000ST

OME-V200

HVO-4000ST

MAJ-2310

A (Red)

B (Green)

C (Blue)

D (White)

Playback terminal

Release terminal

Recording control terminal

SDI input

terminals A to D

3G-SDI quad-link

combined output

1 or 2 terminal

REMOTE contact

switch connectors

MAJ-2309

Red

Blue

Green

Blue

Red

– 3 –

2.1 Inspection of the brake

2.2 Inspection of the caution line (yellow)

2.3 Connection of cables

1Holding the movement handles of this instrument firmly. Check the position of

the brake pedal, push up it with a foot to unlock the casters.

2After stopping this instrument, check the position of the brake pedal, push it

until it hits the back, apply the brake, and confirm that this instrument is locked

to the floor.

Confirm that the caution lines (yellow) on the cover of the

microscope section are invisible. If a caution line (yellow) is

visible, do not use this instrument and contact Olympus.

1Confirm that this instrument and the ancillary

equipment to be used are turned OFF.

2Confirm that the electrical contacts of the

connector of the 4K combined cable 10M

connected to the observation monitor are free

of irregularities such as bending or crushing.

3Hold the connector of the 4K combined cable

10M so that the UP index comes on the top

and insert it into the 3G-SDI quad-link

combined output 1 or 2 terminal all the way

until it clicks.

2 Inspection

Brake pedal

Base

Cover

Caution lines

(yellow)

Microscope

section

combined

cable 10M

Connector

UP index

3G-SDI quad-link

combined output

1 terminal

3G-SDI quad-link

combined output

2 terminal

– 4 –

2.4 Inspection of the power ON

2.5 Inspection of the illumination light

2.6 Inspection of the observation monitor

2.7 Inspection of the image

1Check that the ventilation grilles on the front and rear

of the base of this instrument are not stopped by dust,

a foreign object, or cloth.

2Confirm that the power switch of the LED light source is set to “ (ON)” as described in the instruction manual

for the LED light source.

3Press the power switch of this instrument to turn it ON. The power indicator

lights green and the illumination lamp of the LED light source lights up.

Confirm that the illumination light is output from the illumination lens of the

microscope section.

Operate the observation monitor by following its instruction manual and confirm that it can display images.

1Using a white object such as a piece of gauze as the

subject, bring the focus on it and set so that no

clipped white area is observed on the entire image.

2Keeping this instrument unmovable, tap and hold the

“White balance” button on the touch panel or the

custom switch to which the white balance function is

assigned for about 1 second.

3The white balance display window shows “Completed”, the message is

displayed on the observation monitor and the white balance icon appears on

the touch panel.

Ventilation

grilles

Power indicator

Power switch

Illumination

lens

White balance

White balance display window

White balance icon

– 5 –

2.8 Inspection of the focus/zoom functions

2.9 Inspection of the view field movement

4Place an object having an easy-to judge vertical

direction view so that it is focused on the center

of the image displayed on the observation

monitor. Observe the observation monitor

images without wearing the 3D eyeglasses and

confirm that there is no positioning error in the

up-down direction between the left and right

images.

5Observe the images by wearing the 3D

eyeglasses, close the left and right eyes

alternately, and confirm that there is no difference in color or brightness between the left and right images.

6While observing the 3D images, contact the observed object with forceps or a similar tool and confirm that

there is no peculiarity in the feeling of depth.

7Confirm that the data display is displayed on the observation monitor.

8Observe your hand and confirm that the image is displayed

in normal colors without noise.

1Tilt the scope switches A and B on the microscope

section all the way upward or downward and, by

observing the observation monitor, confirm that the

focus and zoom functions are activated correctly.

2If the zoom + of the adaptive AF is set, confirm that

the auto focus is activated and focus is adjusted after

completion of the zoom + (UP) operation.

1Tilt the joystick on the foot switch all the

way. Observe the observation monitor and

confirm that the field moves to direction in

which the joystick is tilted.

2If the view field movement of the adaptive

AF is set, confirm that the auto focus is

activated after completion of the view field

movement operation.

Observation

monitor

Images without up-down

positioning error

Images with up-down

positioning error

Left image Right image Left image Right image

Data display

Observation

monitor

Observation monitor

Scope

switch A

Scope

switch B

Observation monitor

Joystick

Foot switch

Observation monitor

– 6 –

2.10 Inspection of the arm locking/unlocking

2.11 After inspection

3With the view field movement activated, flip open the

switch cover and press the upper segment of the

view field movement stop switch and confirm that the

indicator above the switch lights orange and the view

field movement is stopped. After checking, press the

lower segment of the view field movement stop

switch and confirm that the indicator is extinguished

and the view field movement is activated.

1Hold the grip of the microscope section firmly, push in the scope switch C with

a finger, and confirm that the arm is unlocked.

2With the arm in the unlocked condition, confirm that the

microscope section and arm can be moved in the necessary

range without causing the feeling of being pulled in a specific

direction.

3Remove your finger from the scope switch C and confirm

that the arm is locked and the microscope section can be

fixed at the current position.

4If the arm free of the adaptive AF is set, confirm that the auto

focus is activated and focus is adjusted after the arm has

been unlocked.

5With the arm set in the unlocked condition by pushing

in the scope switch C with a finger, flip open the

switch cover, press the upper segment of the arm

locking switch and confirm that the indicator above

the switch lights orange and the arm in locked. After

checking, press the lower segment of the arm locking

switch and confirm that the indicator is extinguished

and the arm is unlocked.

1Press the scope switch C and fold the arm in a compact form as shown in

Figure.

2Press the power switch to turn this instrument OFF. Confirm that the power

indicator is extinguished.

View field movement

stop switch

Switch cover Indicator

Scope

switch C

Grip

Switch cover

Indicator

Arm locking switch

Arm

Scope

switch C

Power indicator

Power switch

– 7 –

3.1 Orient the arm to the direction to be used

3.2 Attaching the drape

1This instrument is designed to allow a wide range of

arm positions by enabling “Installation of base on the

right of operator (a)” and “Installation of base on the

left of operator (b)”. Perform the following operation

according to the desired positioning of the arm.

The following steps describe how to change the “Installation of base on the right of operator” to “Installation of

base on the left of operator”. If you need the opposite work, reverse the left and right in the following steps.

2Press the scope switch C on the microscope

section and rotate the microscope section

around rotation axis A shown in (a) by 180

toward the front (in the direction of arrow 1) to

the positioning shown in (b). Then rotate the

microscope section around rotation axis B in

the direction of arrow 2 to change the arm

positioning as shown in (c).

1To facilitate attaching of the drape, press the scope switch

C on the microscope section and extend the arm as shown

in Figure.

2Take out the drape from the package.

3Open the drape in the direction of the arrow.

4Check for adhesion of foreign matter to drape, wetting due to water, etc. If there is an abnormity, replace with

new drape.

3 Operation

(a) (b)

Operator

Base Base

Rotation

axis A

Arrow 1

Microscope

section

Scope

switch C

(a) (b) (c)

Rotation

axis B

Arrow 2

Arm

Microscope section

Scope switch C

Package

Drape

Arrow

– 8 –

5With the orientation of index visible, put your hands in the folded drape and

hold the lens hood.

6Align the convex shape part of the drape attaching bezel

of the microscope section with the convex shape part of

the lens hood and push firmly until the lens hood hits the

drape attaching bezel.

7Hold the lens hood and pinch the seal part,

spread the drape along the arm.

8Push firmly until the lens hood hits the drape attaching bezel.

9Wrap the grip sheet around the grip section of

the microscope section and hold down the

slack of the drape. Peel off the release paper at

the end of the grip sheet and firmly press the

attaching bezel and attach it onto the grip

sheet.

10 Operate the scope switch C of the microscope section and the custom switches 1 to 3, and confirm that each

switch is not pushed and it can operate each switch without a feeling of getting caught. Feel uncomfortable

with the operation of each switch, repeat from Step 9.

Lens hood glass section Lens

hood

Index

Convex

shape part

Lens

hood

Convex shape part

Arm

Seal part

Attach it onto the

grip sheet

Grid sheet

Adhesion

part

– 9 –

11 Fix the drape with 3 straps. Beginning from the

position closer to the microscope section,

attach 3 straps in the same way as above.

12 Press the scope switch C on the microscope section, move the arm, and

confirm that its movement is not hindered. Adjust the swelling of the

drape near the strap when the arm movement is not smooth or when the

switch is unintentionally pushed by the drape. If it still does not resolve

please remove the strap and repeat from Step 11.

13 Check that there is no breakage or adhesion of foreign matter, wetting due to water, etc. If there is an

abnormity, replace with new drape.

14 Check the image of observation monitor is no abnormality.

Fix on the tip side of the

black part.

Black part

Cut out the straps along

the perforations.

Peel off the release paper and

attach it onto the same strap.

How to use the strap

– 10 –

3.3 Loading the user preset

1Tap the “Load user preset” button.

2Tap the user ID button to be set.

3The selected setting will appear on the user ID window on the touch panel.

Load user preset

User ID

User ID window

Andere Handbücher für ORBEYE OME-V200

Inhaltsverzeichnis

Andere Olympus Messgerät Handbücher

Olympus

Olympus OMCL-AC160TN-C3 Bedienungsanleitung

Olympus

Olympus OMCL-AC200TN-C3 Bedienungsanleitung

Olympus

Olympus U-GAN Bedienungsanleitung

Olympus

Olympus 38DL PLUS Bedienungsanleitung

Olympus

Olympus WS 100 - 64 MB Digital Voice Recorder Bedienungsanleitung

Olympus

Olympus USPM-RU-W Series Bedienungsanleitung

Olympus

Olympus Vanta L Series Bedienungsanleitung

Olympus

Olympus BIX III Bedienungsanleitung

Olympus

Olympus SOLTIVE Bedienungsanleitung

Olympus

Olympus STM7-AF Bedienungsanleitung

Olympus

Olympus BondMaster 600 Bedienungsanleitung

Olympus

Olympus 27MG Bedienungsanleitung

Olympus

Olympus 27MG Bedienungsanleitung

Olympus

Olympus USPM-RU-W Series Bedienungsanleitung

Olympus

Olympus 45MG Bedienungsanleitung

Olympus

Olympus OMCL-AC240TS-R3 Bedienungsanleitung

Olympus

Olympus Magna-Mike 8600 Bedienungsanleitung

Olympus

Olympus 45MG Bedienungsanleitung

Olympus

Olympus VN-850PC Bedienungsanleitung

Olympus

Olympus OMCL-AC240TN-R3 Bedienungsanleitung

Olympus

Olympus DM-450 Bedienungsanleitung

Olympus

Olympus EPOCH 650 Bedienungsanleitung

Olympus

Olympus USPM-RU-W Series Bedienungsanleitung

Olympus

Olympus CIX100 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung