Opticon RS232 Bedienungsanleitung

User’s Manual

LGP Series

Handheld CCD Scanner

25-ULGPMU01-01

April 2002

Keyboard Wedge Interface

USB Interface

RS232 Interface

8 Olympic Drive

Orangeburg, NY 10962

Tel 845.365.0090

Fax 845.365.1251

www.opticonUSA.com

Manual No. 25-ULGPMU01-01 Series LGP Handheld CCD Scanner

Table of Contents

PART I CCD Scanning

General Information ...........................................4

Unpacking

Factory Technical Support

Part II Installation and SetUp

A. Installation –Wedge Interface ……………5

Reset all Defaults …………………………………………….6

Computer Type Selection … ............................... 6

Keyboard Wedge and USB Option…………………7

InterCharacter Delay ..........................................8

B. Installation – RS232 Interface................ 9

RS-232C Communication Parameters................10

Baud Rate........................................................10

Data Bits / Stop Bits / Parity..............................11

C. Installation – USB Interface ..................12

_________________________________________

NOTICE

Opticon has taken every step to ensure that the

information included in this manual is accurate,

however we reserve the right to change any

specification at any time without prior notice.

_________________________________________

Part III Bar Code Menu Functions

Section A Programming the Scanner……………….13

Section B Symbology Selections ..................... 14

Enabling only a single symbology...................... 14

Enabling additional symbology......................... 16

Number of Characters…………………………….........18

Setting Options for UPC-A/E ............................. 19

Setting Options for EAN-13 and -8 .................... 21

Code 39 Settings ............................................. 23

Codabar Settings ............................................. 25

2 of 5 Settings................................................. 28

MSI/Plessey Setting ......................................... 30

Code 128 Setting............................................. 31

IATA Settings .................................................. 32

Section C: Universal Selections

Case Conversion.............................................. 34

Prefix Options.................................................. 35

Suffix Options.................................................. 37

Direct Input - Keyboard Keys............................ 39

Direct Input - Characters ................................ 42

Direct Input - Control Characters ...................... 50

Read Mode Settings......................................... 53

Trigger Settings............................................... 54

Beeper Options................................................ 58

Good Read Indicator (LED)............................... 60

Page 3

Manual No. 25-ULGPMU01-01 Series LGP Handheld CCD Scanner

Part I

General Information

The LGP-6125 Series CCD Scanners utilize state-of-the-art imaging technology similar to that found in digital cameras,

facsimile machines and video camcorders. The scanner images the bar code label, then converts the digital signals into data

the host computer can understand. By capturing the bar code image all at once, the scanner provides fast, highly accurate

reading.

Miniature surface mount electronics make up the CCD scanner's solid state construction. CCD scanners have no moving

mechanical parts and provide years of trouble-free operation.

This manual contains information on setting-up the scanner as well as programming various parameters of the scanner.

The LGP6125 scanner is available in several different interface configurations:

Keyboard Wedge Interface

RS232 Serial Interface

USB Interface

There is a specific section of this manual for installing each type of interface. Be sure you are using the section of the

manual that pertains to interface you are using.

Unpacking

Remove the scanner from its packaging and inspect it for damage. If the scanner was damaged in transit, call the dealer or

distributor from whom you purchased it. If you purchased it directly from Opticon, call Opticon Customer Service Dept. at

800-636-0090.

Factory Technical Support

If you have any questions or need assistance with programming your scanner call Opticon Technical Support at 800-636-

0090 please have the unit model number and several bar code labels readily at hand. The model number is located near the

connector end of the cable.

If the scanner must be returned, please contact Opticon to obtain an RMA (Return Merchandise Authorization) number prior

to returning the product. The Customer Service Dept. may be reached at 800-636-0090.

NOTE: Returned merchandise will not be accepted without a RMA number indicated clearly on the outside of the carton.

Page 4

Manual No. 25-ULGPMU01-01 Series LGP Handheld CCD Scanner

Part II Installation and SetUp

This section of the manual contains information on the physical installation of the scanner as well as certain programming options.

There is a separate section for each type of interface. Check to see which type of interface your scanner has and turn to that

section for information on installing the scanner

A.) Installation – Keyboard Wedge Interface

A "Y" connection cable is required for installation. The scanner is installed or "wedged" between the keyboard and the computer..

Your “Y” cable should have connectors for both a PS2 and AT type installation. The "Y" cable connects both the scanner and the

keyboard to the computer.

The scanner must match the type of computer being used. The default setting is for an IBM AT type computer. If this type does

not match the host computer, refer to the “Computer Type Selection” in the programming section that follows. If the connector

does not match the host compute remove the short cable section, reverse it and insert it in the other connector

Page 5

Manual No. 25-ULGPMU01-01 Series LGP Handheld CCD Scanner

Reset All Defaults – Keyboard Wedge Interface

Our scanners are shipped with factory default settings that represent the settings most commonly used by our customers. In most

applications, the scanner will work right out of the box without any need for additional programming. At any time you can return

the scanner to the factory default settings. First scan the Start Program Menu bar code below, then scan the “Reset all Defaults”

programming bar code, and then the End Program Menu bar.

NOTE: (%) A pointing finger indicates default settings throughout the following menus.

ZZ Start

Program Menu [[ 

UB Reset All Defaults

(AT Wedge) VC 

ZZ End

Program Menu [[ 

Computer Type Selection (for Keyboard Wedge only)

The Keyboard Wedge interface scanner is designed to operate with an IBM personal computers and compatibles along with a

Macintosh PC's. Select the host computer type from the menu below.

NOTE: If the scanner has not been set to the correct host computer, the scanner may display random characters on the screen after

reading a bar code label.

ZZ Start

Program Menu [[ 



UA IBM PC/XT VB 

UB IBM AT &

compatibles VC 

UD HP Vectra VE 

UM Macintosh VN 



ZZ End

Program Menu [[ 



Page 6

Manual No. 25-ULGPMU01-01 Series LGP Handheld CCD Scanner

Keyboard Wedge and USB options

With Keyboard: Use this mode in case a keyboard is connected to the PC wedge Y-cable. The Wedge is only listening in case the

computer is booting or the wedge is idle.

Without Keyboard: Use this mode in case no keyboard is connected to the PC wedge Y- cable. In some cases, this mode is

required when a PC USB keyboard is connected. If this option is enable, the computer detects the wedge as a keyboard. If the

computer reports a keyboard error or in case no data is displayed, try this option. It is required to power OFF the PC, wait 10

seconds and power ON the PC.

NOTE: Do not enable ‘without keyboard’ option when a keyboard is connected to the Y cable. The ‘without keyboard’ option is

only supported for PC/AT wedges.

ZZ Start

Program Menu [[ 

KM With keyboard LN 

KL Without keyboard LM 

ZZ End

Program Menu [[ 

Page 7

Manual No. 25-ULGPMU01-01 Series LGP Handheld CCD Scanner

Intercharacter Delay for Keyboard Wedge interface

The scanner may send data faster than the computer or application program can accept. This is called "keyboard buffer overrun".

If data appears to be missing, random read errors occur or the scanner locks up and will not scan, experiment with the various

keyboard timing options listed in the menu to follow.

ZZ Start Program

Menu [[ 

LA No Delay MB 

LB Delay = 1 MB 

LC Delay = 2 MD 

LD Delay = 3 ME 

LE Delay = 4 MF 

LF Delay = 5 MG 

LG Delay = 6 MH 

LH Delay = 7 MI 

LI Delay = 8 MJ 

LJ Delay = 9 MK 

LK Delay = 10 ML 

ZZ End Program

Menu [[ 

Page 8

Manual No. 25-ULGPMU01-01 Series LGP Handheld CCD Scanner

B.) Installation – RS232 Interface

The RS-232 scanner cable is terminated in with a DB9 female connector. An external power supply (+5V DC) may be necessary.

There is a power supply jack on the RS-232 connector.

Installation is as follows:

1. Plug the scanner into an RS232 serial port (such as COM1) of the host PC. If external power is required, insert external power

plug into the jack on the RS-232 connector.

2. Connect the power supply into an electrical outlet (110 V AC)

3. Turn on the power to the host computer. Make sure the communication parameters of the computer match those of the

scanner. The default communications settings are: 9600 baud, 8 data bits, 1 stop bit, no parity, no handshaking

4. Be sure the PC is in a program (such as WordPad) that will accept input from the serial port.

Reset All Defaults – RS232

Our scanners are shipped with factory default settings that represent the settings most commonly used by our customers. In most

applications, the scanner will work right out of the box without any need for additional programming. At any time you can return

the scanner to the factory default settings by scanning the “Reset all Defaults” programming bar codes below. First scan the Start

Program Menu bar code below, then scan the “Reset all Defaults” programming bar code, and then the End Program Menu bar.

ZZ Start

Program Menu [[ 

U2 RS232

Reset all defaults

V3 

ZZ End

Program Menu [[ 

Page 9

Manual No. 25-ULGPMU01-01 Series LGP Handheld CCD Scanner

RS-232C Communication Parameters

Handshaking Protocol

ZZ Start

Program

Menu [[ 



P0 None Q1 

HP04 RTS/CTS +IQ15+



P3 ACK/NAK Q! 



ZG Xon/Xoff [H 



Flow

Control

Time

Unlimited J1 

I1 Flow

Control:

100ms J2 



I2 Flow

Control:

200ms J3 



I3 Flow

Control:

400ms J! 



Baud Rate

K7 19200 L8 

K6 9600 L7 

K5 4800 L6 



K4 2400 L5 



K3 1200 L! 



K2 600 L3 



Page 10

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Opticon Barcode-Lesegerät Handbücher

Opticon

Opticon C 37 Bedienungsanleitung

Opticon

Opticon OPN-2006 BLUETOOTH Programmierhandbuch

Opticon

Opticon UNIVERSAL MENU BOOK Montageanleitung

Opticon

Opticon OPL 7836 Bedienungsanleitung

Opticon

Opticon PX-25 Bedienungsanleitung

Opticon

Opticon NFT 2100 Bedienungsanleitung

Opticon

Opticon CS1504 Bedienungsanleitung

Opticon

Opticon LPN5627 Bedienungsanleitung

Opticon

Opticon OPL 2724 ZAPPER Bedienerhandbuch

Opticon

Opticon OPI-3601 Bedienungsanleitung

Opticon

Opticon OPI 2201 Bedienungsanleitung

Opticon

Opticon OPR 3101 Bedienungsanleitung

Opticon

Opticon OPI 4002 Bedienungsanleitung

Opticon

Opticon RFI3793B Bedienungsanleitung

Opticon

Opticon OPL-9725 Benutzerhandbuch

Opticon

Opticon NLV 2001 Bedienungsanleitung

Opticon

Opticon STD-3201 Bedienungsanleitung

Opticon

Opticon NLV-3101-HD Bedienungsanleitung

Opticon

Opticon OPR 3001 Bedienungsanleitung

Opticon

Opticon OPN2002 Bedienungsanleitung

Opticon

Opticon OPL972X Bedienungsanleitung

Opticon

Opticon OPN2002 Benutzerhandbuch

Opticon

Opticon M-5 Bedienungsanleitung

Opticon

Opticon NLB-1000 Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung