Opticon OPL-9725 Benutzerhandbuch

OPL-9725

Demo Application Manual

Version LFBP0033

OPL 9725 Demo Application

Getting Started

The OPL 9725 is shipped with a demo application loaded on the scanner and ready to use out of the

box. The demo application allows you to collect data and transfer data to your host PC. Data is saved

in the OPL’s RAM disk as a flat text file called SCAN.TXT. The file then can be transferred to your PC

using the NetO32 application which can be installed from the Opticon OPL Product CD supplied with

your OPL. You can also transfer the file to your PC in plain ASCII mode using a terminal application

like HyperTerminal.

NetO protocol is the default communication mode but you can switch to ASCII mode by scanning a

special barcode. Please see the section Switching File Transfer Mode at the end of this document.

Steps to use the demo application:

1. Scan some barcodes using the trigger button on the OPL 9725. The OPL will beep once and the

LED will flash green after each successful scan.

2. Once you are done collecting data, you can send the data file to your PC using NetO32 application.

Note: You must first install and configure NetO32 before you can transfer your data. For

information on installing and configuring NetO32, please refer to the NetO32 Instruction

Manual which can be found on the OPL Product CD supplied with your OPL.

3. Configuring NetO:

a. Set the baud rate to 115200bps (default). If you change the default baud rate, you need to

change the switches on the cradle to match the new baud rate. See the OPL/CRD manual for

details.

b. Set the COM port to match the COM port number to which the CRD 9723 cradle is connected

to on your PC

c. Configure your download folder. This is the folder in which NetO will save your data file after

downloading.

d. Configure the File Download mode (options are Append, Overwrite and Unique). Please refer

to NetO’s Instruction Manual for details on each of these modes.

Version LFBP0033 Page 2

OPL 9725 Demo Application

4. Downloading your data file:

a. Make sure the cradle is connected to a COM port on your PC and is powered on.

b. Place the OPL on cradle

c. Start NetO Protocol by selecting Protocol

Start

from the Menu. When Neto protocol is running, the

amber light on the cradle will be blinking. You should

see the file download progress on NetO’s main screen.

The file SCAN.TXT should now be available in the

download folder you configured in step 3.c above.

d. The file is deleted from the OPL after download.

Data Format

Data is formatted as comma delimited variable length fields in the file with each record on a separate

line as follows:

Example:

070330506060,03/22/2007,14:17:47

070330506060,03/22/2007,14:17:48

070330506060,03/22/2007,14:17:49

Version LFBP0033 Page 3

OPL 9725 Demo Application

Version LFBP0033 Page 4

Switching File Transfer Mode

The default data transfer mode is NetO. You can switch between NetO and plain ASCII modes by

scanning the corresponding barcode from the table below.

When using plain ASCII mode, the file is transferred automatically to the PC when the OPL is placed

on the cradle. The file is deleted after transmission. You need to use your own terminal application

like HyperTerminal to receive the data.

If you’re using HyperTerminal, you can configure it to capture data in a file using the menu option

Transfer ÆCapture Text. Please refer to HyperTerminal help for details.

It is a good idea to test your unit using simulated data after making any setting changes before

collecting real data.

+008+ PLAIN ASCII ,119, 

+009+ NETO ,11:, 

CAUTION:

When using Plain ASCII mode, Do not place the OPL on the cradle until the host computer

program is running and ready to receive data.

Inhaltsverzeichnis

Andere Opticon Barcode-Lesegerät Handbücher

Opticon

Opticon OPR 3101 Bedienungsanleitung

Opticon

Opticon CS1504 Bedienungsanleitung

Opticon

Opticon OPN2005 Bedienungsanleitung

Opticon

Opticon OPR 3101 Referenzhandbuch

Opticon

Opticon OPI 4002 Bedienungsanleitung

Opticon

Opticon OPR3301 Bedienungsanleitung

Opticon

Opticon OPR 3001 Bedienungsanleitung

Opticon

Opticon PHL 2700 Bedienungsanleitung

Opticon

Opticon OPI 2201 Bedienungsanleitung

Opticon

Opticon PX-25 Bedienungsanleitung

Opticon

Opticon NFT 1125 Series Bedienungsanleitung

Opticon

Opticon NFT 2200 Bedienungsanleitung

Opticon

Opticon OPR 2001 Bedienungsanleitung

Opticon

Opticon Code Reader 2.0 Bedienungsanleitung

Opticon

Opticon OPN2003 Bedienungsanleitung

Opticon

Opticon OPR 3101 Bedienungsanleitung

Opticon

Opticon NFT 2100 Bedienungsanleitung

Opticon

Opticon RS232 Bedienungsanleitung

Opticon

Opticon OPH 1004 Bedienungsanleitung

Opticon

Opticon CRD-3301 Bedienungsanleitung

Opticon

Opticon OPN-2006 BLUETOOTH Programmierhandbuch

Opticon

Opticon OPR 2001 Bedienungsanleitung

Opticon

Opticon NFT 1125 Series Bedienungsanleitung

Opticon

Opticon CRD972X Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung