Oreck Edge Bedienungsanleitung

Increase Quality Through Interaction with the Field

The Oreck Manufacturing Company

Oreck Edge - Upright Tune-Up & Service

Guide

02/26/2010

Compiled by Clark DeNoble

Increase Quality Through Interaction with the Field 1

Increase Quality Through Interaction with the Field

Table of Contents

Electrical Page 3

Tune-Up

Evaluate Page 4

Clean Page 4

Replace Page 5

Low Power/Sparks Pages 5 – 6

Wheels Grinding/Rattling/Worn Page 6

Part Replacement/Disassembly

Sole Plate Page 7

Lens/Fascia/Top Cover Pages 7 - 8

Brushroll Page 8

Belt Page 9

Power Supply Page 9

Valve Assembly Pages 10 - 11

Valve Service Pages 11 – 13

Control Board Page 13

Motor Module Pages 14 –15

Motor Pages 15 – 16

Fan Housing Module Page 16

Outer Bag Pages 16 – 18

Grip Pages 19 – 20

Harness Pages 20 – 21

Lifter Pages 21 – 23

Troubleshooting

Valve Stuck in Hose Position Page 23

Valve Stuck in Nozzle Position Pages 24 – 25

Nothing Works Pages 25 – 28

Everything Works But The Motor Page 28

Everything Works But The LED Lights Page 29

Features of the Edge

1. Electronic Motor Speed Control

2. Electronic Motor Stop – If the fan jams the motor will stop which save both the

motor and the belt.

3. Mechanical nozzle lift prevents brushroll contact with the floor surface when

the unit is in the accessory hose mode or locked upright and left running.

4. Electronic Suction Path Valve Control - When the hose is attached and the unit

is upright and locked, the suction path is through the hose. When the unit is

moved from the upright and locked position to the normal use position, the

suction path automatically changes to through the power nozzle. If the hose isn’t

installed then the path stays through the nozzle no matter the position of the unit.

Increase Quality Through Interaction with the Field 2

Increase Quality Through Interaction with the Field

Electrical

1. The fuse on the logic board is for fire safety, not to protect the board.

2. If the motor current increases and the fuse doesn’t blow, then the chip will

shutdown the motor.

3. If left plugged in the unit will return to the speed in use when it was turned off. If

unplugged then the speed will rev up to full speed.

4. On the power supply board the resistor marked ☼will blow if the board goes bad.

5. If the LEDs are On but the unit doesn’t function, turn Off, unplug, wait 30 seconds

and plug it back in. Turn it On and the unit should work.

Increase Quality Through Interaction with the Field 3

Handle Switch

On/Off High Speed Low Speed

Motor

Line

Control/Triac 110-120VAC

Line

eutral

Servo

–

Brown – On/Off 5vdc

Yellow – Low Speed 5vdc

Red – High Speed 5vdc

☼

Black

Brown

Switch White

Not Used

lack

–

Line

Red – 12 VDC

☼

Fuse

Common - Brown

12VDC - Black

12VDC - White

White - Neutral

Hall Effect Sensor

Brown on the bottom

White in the middle

Black on top

Increase Quality Through Interaction with the Field

Tune-Up

1. Evaluate

a. Cord assembly and harness condition

i. Jacket free of holes especially at the entrance to the handle

grip or nozzle housing

ii. Plug blades secure and straight

b. Cord dump function

i. Holds in place while winding the cord

c. Housing condition

i. Tells a lot about how the unit was treated by the user

ii. Fascia fixed in place

d. Base/Sole plate assembly condition

i. Normal wear

ii. Edge brush condition

iii. Microsweep condition

iv. Rear wheel condition & function

v. Front wheel condition & function

e. Bumper condition

f. Outer bag condition

g. Inner bag dock condition & function

h. Dirt tube condition

i. Collar condition

j. Handle condition

k. Switch condition & function

l. Motor condition & function

m. Brushroll condition & function

n. Belt condition & function

o. Light cover condition & light function

p. Yoke condition & function

q. Pivot detent

r. Accessory valve condition & function

s. Height adjuster condition & function

2. Clean

a. Check for clogging at the inlet of the pivot.

b. Check the fan and fan housing for foreign objects.

c. Clean the components:

i. WD40 to remove marks from cords and bumpers

ii. Oreck Glass & Mirror Cleaner

iii. Oreck Hospital Clean (Liquid only, not the aerosol)

iv. Steam cleaning is an effective method of cleaning.

v. Use soap (Joy, Ivory, Dawn) and water as the primary

cleaning ingredients.

vi. Do not use Citrus-based cleaners (orange oil). They will

cause most plastic to become brittle.

Increase Quality Through Interaction with the Field 4

Increase Quality Through Interaction with the Field

3. Replace

a. Inner filter bag

4. Only when necessary - Low Power/Sparks - Commutator Polish

a. It is not necessary to polish all commutators. Commutators in

pictures 1 & 2 have a gray film. This is graphite from the brushes

and desirable since it acts as a lubricant. Picture 3 shows heat and

4 uneven wear. These two should be polished.

1 2 3 4

b. Hazardous conditions will exist during this step:

i. Wear safety glasses, remove jewelry from hands, wrists and

neck (if dangling). Secure loose clothing and long hair.

c. Another way to determine if polishing is necessary is to observe the

arcing characteristics of the function while in operation.

d. Maximum Acceptable Arc – Continuous no greater than 1/16”

e. Commutators producing more than the maximum acceptable arc

should be polished. Brushes may have to be changed.

f. Hazardous conditions will exist during this step:

i. Exposure to spinning components: brushroll, motor, belt,

fan and exhaust debris.

ii. Wear safety glasses and remove jewelry from hands, wrists

and neck (if dangling). Secure loose clothing and long hair.

iii. Exposure to lethal amperage: Keep hands away from

terminals, wires and motor components

g. Lightly touch the commutator with the commutator cleaner.

Burnishing will happen quickly.

h. Turn the commutator cleaner over and do the same for the belt

drive shaft.

Increase Quality Through Interaction with the Field 5

Increase Quality Through Interaction with the Field

i. Turn the unit off and unplug from outlet.

5. Wheels Grinding/Rattling/Worn - Rear Wheel Service

a. Remove hubcap – Insert flathead screwdriver blade into one of the

3 slots on the back of the wheel hub. Place the blade as shown in

picture 1 and twist until hub tab has unhooked from the wheel hub

picture 2, then push down.

b. Remove wheel – Remove E clip and washer

Washer E clip

c. Remove Axle – Remove 2 screws from the cord over-mold and the

yoke cover (Picture 1). Slide out the axle (Picture 2).

Yoke Cover

Cord Over-mold

End of Tune-up section

Increase Quality Through Interaction with the Field 6

Increase Quality Through Interaction with the Field

Part Replacement/Disassembly

(Reverse to Reassemble)

1. Sole Plate

a. Extract 6 screws (#2 Phillips)

b. Remove Edge Brush – Find the round tab (Circled). With a

punch and hammer knock out the edge brush

c. The edge brushes are marked left L and right R. Line up the tab

with the sole plate hole and snap in place

2. Lens/Fascia/Top Cover

a. To remove the fascia the lens must be removed and two screws

extracted. Pry the lens away at one end, bend it out so the end

tab pops free (Picture) and do the same with the tabs along its

length.

Increase Quality Through Interaction with the Field 7

Increase Quality Through Interaction with the Field

b. Extract the two screws indicated, slide the fascia forward and

set aside.

c. To remove the top cover extract two screws indicated and lift it

off.

3. Brushroll – Requires 1,2 & 4

a. Service the brushroll

b. Install – The end caps must be oriented as shown or the belt

won’t track correctly.

Baseplate

Increase Quality Through Interaction with the Field 8

Increase Quality Through Interaction with the Field

4. Belt – Requires Steps 1, 2 & 3

a. Fit the belt to the brushroll pulley. Fit the brushroll/belt assembly

to the base. Feed the belt through the slot (Picture 1). Use a

3/8” or 10mm socket or nut driver (Picture 2) to capture the

motor shaft (Picture 3) and pivot the belt on to it (Picture 4), this

will require that the belt be encouraged onto the motor shaft. Be

sure the belt is centered and fully seated (Picture 5). If the short

socket doesn’t work for you try a deep socket (Picture 6 top) or

a hollow shaft 7/16” nut driver with the head cut off (Picture 6

bottom & Picture 7). Make sure the belt is seated in the brushroll

pulley

1 2

3 5

5. Power Supply – Requires Step 2

a. Unplug from control board and lift out.

Increase Quality Through Interaction with the Field 9

Increase Quality Through Interaction with the Field

6. Valve Assembly – Requires Step 2

a. Remove the hose coupler. Extract the clamp and valve module

screws indicated and remove the clamp. Loosen the motor

module screws about ¼”.

Hose Coupler

Valve Module

Motor Module

Clam

b. Where they interface, tilt both modules up and move the valve

module carefully out of the way to expose the valve connections

to the control board.

Increase Quality Through Interaction with the Field 10

Andere Handbücher für Edge

Inhaltsverzeichnis

Andere Oreck Staubsauger Handbücher

Oreck

Oreck Simply Amazing XLPRO6A Bedienungsanleitung

Oreck

Oreck XL U2640RH Bedienungsanleitung

Oreck

Oreck U2251 Bedienungsanleitung

Oreck

Oreck Aviator Upright Series Bedienungsanleitung

Oreck

Oreck XL21 Series Bedienungsanleitung

Oreck

Oreck XL7 705 SERIES Bedienungsanleitung

Oreck

Oreck XL2200RS Bedienungsanleitung

Oreck

Oreck STEAM 75 75 Bedienungsanleitung

Oreck

Oreck XL Edge Bedienungsanleitung

Oreck

Oreck XL2100RHS Bedienungsanleitung

Oreck

Oreck U2250 Bedienungsanleitung

Oreck

Oreck XL 2635RH Bedienungsanleitung

Oreck

Oreck XL 2310RS Bedienungsanleitung

Oreck

Oreck XL36R7HH Bedienungsanleitung

Oreck

Oreck UK30200 Bedienungsanleitung

Oreck

Oreck XL2200RS Bedienungsanleitung

Oreck

Oreck Magnesium OK2 Bedienungsanleitung

Oreck

Oreck Steemer XLS465 Bedienungsanleitung

Oreck

Oreck XL U3760HH Bedienungsanleitung

Oreck

Oreck Professional Series Gold Bedienungsanleitung

Oreck

Oreck Simply Amazing U4070H2 Bedienungsanleitung

Oreck

Oreck XL U2200RD Bedienungsanleitung

Oreck

Oreck XL COMPACTO 6 Bedienungsanleitung

Oreck

Oreck XL3605HH Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch