oventrop REGTRONIC PM Bedienungsanleitung
INSTRUCTIONS FOR
INSTALLERS
Oventrop
REGTRONIC PM
Important!
Please read the instructions carefully before installing and operating the unit!
Failure to do this can void product warranty!
Please keep the instructions in a safe place!
This unit described has been manufactured and inspected according to CE
regulations.
Instructions for installers REGTRONIC PM
Instructions for installers 136955080 2 1317ZB010-10B-E, Revised 03/2008
REGTRONIC PM
Parameters set using the System Settings menu should only be
configured or modified by installers or qualified technical personnel.
Setting the wrong parameters can compromise the functionality of the
control unit and solar power system
Table of Contents:
1
"SYSTEM SETTINGS" MENU/ CHANGES TO THE SYSTEM..................................................... 3
2
USING A DATASTICK
®
................................................................................................................. 4
2.1
F
ACTORY SETTINGS
.................................................................................................................. 4
2.1.1
Restoring factory settings.................................................................................................. 4
2.1.2
Saving/loading configuration parameters.......................................................................... 4
2.2
U
PDATING SYSTEM SOFTWARE
.................................................................................................. 4
Instructions for installers REGTRONIC PM
Instructions for installers 136955080 3 1317ZB010-10B-E, Revised 03/2008
REGTRONIC PM
1 "S
YSTEM
S
ETTINGS
"
MENU
/
C
HANGES
TO THE SYSTEM
During normal operation, the "System
Settings" menu only displays parameters
and does not allow them to be altered.
This prevents accidental changes. To
change parameters, this menu must be
selected within one minute of switching
on the unit.
While the system is running, changes can
be made using the System Settings menu
by pressing the top , bottom
and right-hand button
simultaneously.
Once the user is in the menu, no time
limits apply.
The System Settings menu "locks"
itself automatically one minute after the
unit has been switched on and one
minute after the user has exited the
menu.
The System Settings menu is used to
select the basic schema and the language,
and also to activate or deactivate the
available protective and ancillary features.
The buttons and are used
to page through the various submenus.
The status – e.g. "On" or "Off" – is also
shown next to the name of each submenu.
Submenus are selected by using the
button.
Allocation of layout no. to system number: M1013 = 3310, M1016 = 3311, M1020 = 3312,
M1021=3313, M1022=3314, M1023=3315, M1024=3316, M1026=3317, M1027=3318,
M1028=3319, M1032=3320, X1010=3301, X1020=3302, X1030=3303.
Note: 3300 is the initial software set!
Example: Change system from 3300to 3310
System sel.
[off]
off
System
3300
on
off ok
ok
3300 3301 ok
ok
Service
[off]
MultiReg3
[off]
Instructions for installers REGTRONIC PM
Instructions for installers 136955080 4 1317ZB010-10B-E, Revised 03/2008
REGTRONIC PM
2 U
SING A
D
ATA
S
TICK
®
An installer or technician can use a DataStick
®
for the following tasks:
Updating unit parameters
Saving/loading factory settings
Updating system software
2.1 Factory settings
Factory settings can be saved, loaded or
restored in the "System Settings" menu. This also makes it possible to transfer
configuration data from one control unit to
another, for example.
2.1.1 Restoring factory settings
Menu item "Factory settings":
•Off
•On: Restores the default factory settings
2.1.2 Saving/loading configuration parameters
Menu item "Factory settings". Parameters:
Only insert or remove the DataStick
®
at this menu. If the DataStick
®
has been previously
used as a programming stick, then other menus in the system will ask the user if the software
on the DataStick
®
should be loaded! Parameter backups on the stick will not have this effect.
•Off
•Save
•Stick available: Message "OK"
-Stick unavailable: Message "OK" (the data will be sent, although it cannot be
stored)
•Load
-Stick available, system no. and system version on the stick match the data in
the control unit: Message "OK"
-Stick available, system no. on the stick matches the data in the control unit,
but the version is different: Message "Chk. par."
: the installer needs to check and verify the parameters.
-System no. does not match the system no. in the control unit: Message "Error"
2.2 Updating system software
First, insert the DataStick. If the DataStick
contains a software package that is valid
for this unit, then the screen will display
"Copy DataStick start?". Press the "OK"
button twice to confirm, and the copy
process will start. Once copying has
finished, the unit will ask you to remove
the DataStick. The control unit will then
reboot.
Andere oventrop Controller Handbücher
oventrop
oventrop Regtronic KM IP Bedienungsanleitung
oventrop
oventrop REGTRONIC PX Bedienungsanleitung
oventrop
oventrop Aktor M Handbuch
oventrop
oventrop Hydromat DTR Bedienungsanleitung
oventrop
oventrop R-Tronic Bedienungsanleitung
oventrop
oventrop REGTRONIC PX Bedienungsanleitung
oventrop
oventrop 1158021 Bedienungsanleitung
oventrop
oventrop NR 230 Bedienungsanleitung
oventrop
oventrop Regtronic BS/2-B Bedienungsanleitung
oventrop
oventrop OV-5 Betriebsanleitung
oventrop
oventrop Hydromat DFC Betriebsanleitung
oventrop
oventrop Aktor M ST L Bedienungsanleitung
oventrop
oventrop Aktor M ST L Modbus Bedienungsanleitung
oventrop
oventrop Hydromat DP DN 25 Handbuch
oventrop
oventrop Regtronic RD-W Bedienungsanleitung
oventrop
oventrop Aktor M ST/2P L Bedienungsanleitung
oventrop
oventrop Hycocon DTZ Bedienungsanleitung
oventrop
oventrop Hydromat DTR Series Bedienungsanleitung
oventrop
oventrop REGTRONIC PC Bedienungsanleitung
oventrop
oventrop Regtronic RX Bedienungsanleitung
