OWC U.2 NVMe Interchange System Leitfaden

Assembly Manual & User Guide

U.2 NVMe Interchange System

for Mercury Helios 3S

Install up to 16TB

U.2 NVMe SSD

Designed for

global workows

Locking drive bay

U.2 NVMe Interchange System for Mercury Helios 3S Contents

CONTENTS

Introduction

1.1 Minimum System Requirements.............................................. 1

-Mac Requirements

-PC Requirements

1.2 Package Contents..................................................................... 1

1.3 About This Manual.................................................................... 1

1.4 Rear View................................................................................... 2

1.5 Usage Notes.............................................................................. 3

Device Setup

2.1 Assembly Steps ........................................................................ 4

Support Resources

3.1 Formatting ............................................................................... 10

3.2 Troubleshooting ...................................................................... 10

3.3 About Data Backup ................................................................. 10

3.4 Contacting Technical Support................................................ 10

U.2 NVMe Interchange System for Mercury Helios 3S Introduction

1.1 Minimum System Requirements

Mac Requirements

-macOS 10.14.5 or later

PC Requirements

-Windows 10 or later

Hardware

-OWC Mercury Helios 3S

-Mac or PC with a Thunderbolt 3 port

Supported U.2 Drives

-2.5-inch U.2 NVMe SSD drive with a PCIe interface

-SATA or SAS drives are not supported

-Hot-swap is not supported (Disconnect the Mercury Helios 3S to swap the drive)

1.2 Package Contents

1.3 About This Manual

The images and descriptions may vary slightly between this manual and the unit shipped. Functions

and features may change depending on the rmware version. The latest product details and warranty

information can be found on the product web page. OWC’s Limited Warranty is not transferable and

subject to limitations.

INTRODUCTION

U.2 NVMe Interchange System

for Mercury Helios 3S

Quick Start Guide

U.2 NVMe Interchange System for Mercury Helios 3S Introduction

To avoid damage, do not expose the device to temperatures outside:

-Environmental (Operating)

-Temperature (ºF): 41º — 95º

-Temperature (ºC): 5º — 35º

-Environmental (Non-Operating)

-Temperature (ºF): -4º — 140º

-Temperature (ºC): -20º — 60º

-Protect your device from excessive exposure to dust during use or storage. Dust can build

up inside the device, increasing the risk of damage or malfunction.

-Do not block any ventilation openings on the device. These help to keep the device cool

during operation. Blocking the ventilation openings may cause damage to the device and

cause an increased risk of short-circuiting or re.

-Read this guide carefully and follow the recommended steps for assembly.

-Use proper anti-static precautions while installing this device. Failure to do so can cause

damage to your drive and/or the PCIe enclosure.

-Do not attempt to disassemble or modify the device. To avoid any risk of electrical shock,

re, short-circuiting or dangerous emissions, never insert any metallic object into the

device. If it appears to be malfunctioning, please contact technical support.

-Never expose your device to rain or use it near water or in damp or wet conditions. Never

place objects containing liquids on the device, as they may spill into its openings. Doing so

increases the risk of electrical shock, short-circuiting, re or personal injury.

General Use Precautions

Safety Precautions

1.4 Rear View

1. Security lock – use the included keys to unlock

or secure the U.2 drive carrier tray to the Mercury

Helios 3S.

2. Security slot – connect a security tether here.

U.2 NVMe Interchange System for Mercury Helios 3S Introduction

1.5 Usage Notes

-To ensure no data is lost during normal use, always eject or unmount the corresponding disk(s) from

your operating system before disconnecting the Mercury Helios 3S from power. Several options are

provided below for Mac and PC.

-macOS

-Drag the disk icon to the trash can in the Dock; OR

-Right-click the disk icon on the desktop, then click ‘Eject’; OR

-Highlight the disk icon on your Desktop and press Command-E.

-Windows

1. Go to the System Tray (located in the lower right corner of your screen). Click on the “Eject” icon

(a small green arrow over a hardware image).

2. A message will appear, detailing the devices that the “Eject” icon controls, i.e., “Safely remove...”

Click on this prompt.

3. You will then see a message that says, “Safe to Remove Hardware.” It is now safe to disconnect

the Mercury Helios 3S from the computer.

-The steps above are applicable to Windows 10 build 1803 and earlier. If you are using Windows 10 build

1809 (October 2018) or later, you can eject the drive by clicking the ‘Show hidden items’ menu in the

Taskbar, then clicking ‘Safely Remove Hardware and Eject Media’, and last select the ‘Eject’ option for this

volume.

U.2 NVMe Interchange System for Mercury Helios 3S Device Setup

DEVICE SETUP

2.1 Assembly Steps

This section describes the process of setting up and installing the U.2 NVMe Interchange System for

Mercury Helios 3S; drive formatting information is available in Section 3. If you received this product

pre-installed and need to replace the U.2 drive, start with the nal step and work backward to Step 6, at

which point you can replace the drive and then follow the same instructions back to the nal step.

1. Loosen the captive thumbscrews on the back of the

Mercury Helios 3S until they spin freely.

2. Set the enclosure on its side then grip the front

grill and slide the inner chassis out of the outer

enclosure.

3. Remove both of the highlighted thumbscrews. Set

the screws and the inner chassis aside.

U.2 NVMe Interchange System for Mercury Helios 3S Device Setup

4. Set the U.2 NVMe Interchange System in front of

you then turn the key to unlock the drive tray.

5. Pull the drive tray out and separate it from the

outer case.

6. Flip the drive tray over and set it on a at surface.

Place the U.2 drive into the drive tray making sure the

connector on the drive is align with the connector on

the tray.

7. Slide the drive forward until it is fully seated on

the U.2 connector. Minimal force is required.

U.2 NVMe Interchange System for Mercury Helios 3S Device Setup

8. Carefully ip the drive tray over and ax the drive

to the tray using the four included drive screws, at

the locations shown. Be sure all four screws are

alike; there is a fth screw used later that is similar

to but not exactly like the others. For now set the

tray and drive aside.

9. Align the inner chassis of the Mercury Helios 3S

and the outer case of the U.2 interchange system

as shown.

U.2 NVMe Interchange System for Mercury Helios 3S Device Setup

11. Carefully ip the Mercury Helios 3S over so that it’s

resting on its feet as shown. Ax the last included

screw at the location shown.

10. Carefully seat the interchange system into the PCIe slot,

making sure the bracket ends slot into their cutouts,

located on the bottom of the Mercury Helios 3S.

12. Re-ax the two thumbscrews you removed

in Step 3, to secure the PCIe bracket on the

Interchange system.

U.2 NVMe Interchange System for Mercury Helios 3S Device Setup

14. Re-fasten the two captive thumbscrews you

loosened in Step 1.

13. Again set the combined inner chassis and outer case

on their side, then slide them into the outer enclosure

of the Mercury Helios 3S, until the front grill is ush

with the edge of the enclosure.

15. Take the drive tray, oriented as shown, and carefully

slide it into the back of the Mercury Helios 3S. Once

the connector on the tray is fully seated, the edge

of the tray should be ush with the edge of the

Mercury Helios 3S.

Inhaltsverzeichnis

Andere OWC Gehäuse Handbücher

OWC

OWC Mercury On-The-Go Bedienungsanleitung

OWC

OWC Mercury Elite-AL Pro Bedienungsanleitung

OWC

OWC Mercury On-The-Go Pro Series Bedienungsanleitung

OWC

OWC ThunderBay 4 mini Leitfaden

OWC

OWC ThunderBay 4 Leitfaden

OWC

OWC Envoy Pro Bedienungsanleitung

OWC

OWC Mercury Elite Pro Dual mini Leitfaden

OWC

OWC Mercury On-The-Go Pro Bedienungsanleitung

OWC

OWC Mercury Elite Pro Dual Bedienungsanleitung

OWC

OWC Mercury Elite Pro Dual Leitfaden

OWC

OWC data doubler Bedienungsanleitung

OWC

OWC TB2U3DKR2 Bedienungsanleitung

OWC

OWC Mercury Elite Pro Dual Leitfaden

OWC

OWC Envoy Pro Bedienungsanleitung

OWC

OWC Mercury Elite-AL Pro Bedienungsanleitung

OWC

OWC ENVOY EXPRESS Bedienungsanleitung

OWC

OWC OWCMANVLS2ASY Bedienungsanleitung

OWC

OWC Mercury Elite-AL Pro Bedienungsanleitung

OWC

OWC OWC “Value Line” Bedienungsanleitung

OWC

OWC Mercury Elite-AL Pro Bedienungsanleitung

OWC

OWC Value Line Bedienungsanleitung

OWC

OWC Mercury Elite-AL Pro Bedienungsanleitung

OWC

OWC Mercury Elite Pro Dual Bay Bedienungsanleitung

OWC

OWC Mercury Elite Pro Dual Leitfaden

Beliebte Gehäuse Handbücher anderer Marken

SilentiumPC

SilentiumPC Armis AR5 Handbuch

Pulsar

Pulsar 17/TRP80/DSPR Bedienungsanleitung

Thermaltake

Thermaltake V150 TG Bedienungsanleitung

MSI

MSI MPG SEKIRA 500X Bedienungsanleitung

Antec

Antec Dark fleet DF-10 Bedienungsanleitung

Nexans

Nexans WTC05 Bedienungsanleitung

Peavey

Peavey DS 1502 Bedienungsanleitung

D-Link

D-Link ShareCenter Pro DNS-1550-04 Bedienungsanleitung

Rosewill

Rosewill RX82-U(JBOD) Bedienungsanleitung

QNAP

QNAP SAS JBOD CLI 1.0 Bedienungsanleitung

GAMDIAS

GAMDIAS Talos P1 Bedienungsanleitung

Auvs

Auvs KR615 Bedienungsanleitung

Digitus

Digitus DA-71114 Bedienungsanleitung

CommScope

CommScope FDH 3000 Bedienungsanleitung

FS FHD-FWME4 Bedienungsanleitung

JBL

JBL CS1215T Bedienungsanleitung

Pulsar

Pulsar ARAD-S4 Bedienungsanleitung

Pulsar

Pulsar AWO454 Bedienungsanleitung