Pacific Z26BA Bedienungsanleitung

Page 1 of 35

Z26BA

The contents of this manual are based on the

latest product information available at the

time of publication. Pacific reserves the right

to make changes or improvements to its

machines without notice.

Carefully inspect all components to ensure

that there is no concealed freight damage. If

such damage is discovered, file a

“CONCEALED DAMAGE REPORT”

immediately with the delivering carrier.

FOR YOUR CONVENIENCE, RECORD

THE FOLLOWING IMPORTANT

INFORMATION:

For new manuals write to:

Pacific

2259 S. Sheridan

Muskegon, MI 49442-6252

or download the most recent version of the

manuals from our website:

www.pacificfloorcare.com

SERIAL NUMBER

DATE PURCHASED

Page 2 of 35

SAFETY INSTRUCTIONS

1) You must have training in the operation of the machine before using it. READ THE

INSTRUCTION BOOK. If you do not understand any instruction, ask your supervisor.

2) Make sure all labels, decals, warnings, cautions and instructions are fastened to the

machine.

3) Read the labels carefully on the machine. Do not cover them for any reason and

replace them if damaged.

4) Do not operate this machine unless it is completely assembled and inspect the machine

carefully before operation.

5) Pay close attention to other people and especially children while operating this machine.

6) Be a careful driver and do not strike shelving or scaffolding, especially where there is a

danger of falling objects.

7) Machines can cause an explosion when operated near flammable materials and vapors.

Do not use this machine with or near fuels, grain dust, solvents, thinners, or other

flammable materials.

8) In case of fire, use a powder extinguisher. Do not use water.

9) Do not use this machine as a means of transport.

10) Do not use acid solutions that could damage the machine.

11) Adjust your speed to the conditions of the floor.

12) Do not turn the machine on an incline. Do not stop and leave the machine on a ramp or

incline.

13) During any maintenance operation disconnect the power supply from the machine.

14) Lead acid batteries generate gases that can cause an explosion. Read the instruction

manual supplied with the battery charger. Keep sparks and flames away from batteries.

NO SMOKING. Charge the batteries only in an area with good ventilation.

15) Do not use a charger if the power cord is damaged or if charger is not rated for the

machine.

16) Always wear eye protection and protective clothing when working near batteries.

Remove all jewelry. Do not put tools or other metal across the battery terminals, or on

the top of the batteries.

17) Maintenance and repairs must be performed by authorized Service Centers only.

18) Keep the electrical parts of the machine dry. Do not wash the machine with direct water

jets or high pressure, or with corrosive material. For storage, keep the machine in a dry

location.

19) Water solutions or cleaning materials used with this type of machine can leave wet

areas on the floor surface. These areas can cause a dangerous condition for the

operator or other persons. Always put CAUTION signs near the area you are cleaning.

20) Do not reach under shrouds with fingers, hands, or toes when machine is running.

Page 3 of 35

SYMBOLS USED ON THE AUTOMATIC SCRUBBER

Water Valve Indicator

Brush Drive Motor Control Switch

Vacuum Motor Control Switch

Battery Charge Indicator

Main Machine Power Key Switch

Squeegee Lift Control Lever

Solution Flow Rate Adjusting Lever

Page 4 of 35

MACHINE PREPARATION

1) UNPACKING THE MACHINE

a) Take off the outer

packaging.

b) The machine is fastened to

the pallet with wooden

wedges that block the

wheels. Remove tie down

straps.

c) Using a ramp, pull the

machine off the pallet.

2) BATTERY INSTALLATION

a) Remove the squeegee hose

from the recovery tank.

b) Remove the vacuum cover

by rotating it

counterclockwise.

c) Remove recovery tank by

lifting tank by lift chain at the

back of the tank and the

drain hose at the front of the

tank.

Remove

Lift Chain

Drain Hose Lift Point

Page 5 of 35

MACHINE PREPARATION

BATTERY INSTALLATION

(Cont.)

d) Place the batteries in the

battery compartment.

e) Connect the battery

connector to the machine

connector

f) Replace the recovery tank

and reassemble the vacuum

cover and squeegee hose.

3) BATTERY CHARGE LEVEL

INDICATOR

The battery indicator is digital with

4 display levels and a flashing one.

The numbers, which appear on the

display, show the approximate

charge level. 4 represents a full

charge and 0 represents

discharged and the batteries must

be recharged.

NOTE: The brush motor

automatically switches off after

the battery indicator light

begins to flash. You will be

able run the vacuum motor and

finish drying any wet areas.

Battery Charge

Indicator

Machine Connector

Battery Connector

Page 6 of 35

MACHINE PREPARATION

4) SQUEEGEE ASSEMBLY INSTALLATION

The squeegee is assembled to the machine

by lifting the locking latches and sliding the

squeegee assembly onto the 2 posts at the

rear of the squeegee swing arm. Push on the

locking latches down. Lower the squeegee

and install vacuum hose over vacuum outlet

on squeegee assembly. The hose should be

located to the rear of the lifting cable.

5) ADJUSTING SQUEEGEE HEIGHT

The height from floor to squeegee should be

adjusted based on blade wear. Rotate the

adjusting knobs counter-clockwise to lower

squeegee and clockwise to lift it.

NOTE: Rotate the right and left adjusting

knobs until the squeegee is positioned parallel

to the floor.

6) ADJUSTING SQUEEGEE INCLINATION

During operation the rear squeegee blade is

most efficient when bent backwards roughly

3/16ths to 5/16ths of an inch along its entire

length. To increase the blade bending in the

center of the squeegee, tilt the squeegee body

backward by turning the adjuster knob

counter-clockwise. Conversely, turn the

adjuster knob clockwise to increase the

bending at the outside edges of squeegee

blade.

Locking Latches

Vacuum

Outlet

Height

Adjusting

Knobs

Inclination

Adjusting

Knob

Page 7 of 35

MACHINE PREPARATION

7) RECOVERY TANK

Open the lid and confirm the following

connections are secure:

a) The vacuum cover is securely attached.

Align the notches and rotate the cover

clockwise to close. The vacuum hose

must also be attached.

b) Confirm that the squeegee hose is properly

connected.

c) Confirm that the drain hose plug, which is

located at the front of the machine, is

closed.

8) SOLUTION WATER

Fill the solution tank with clean water at a

temperature not higher than 50°C / 122°F. Add

the proper concentration of liquid detergent by

following the manufacturer instructions. Excess

foam in the recovery tank can damage the

vacuum motor, so use only the minimum amount

of detergent necessary. Reassemble the cover.

WARNING! Always use low foaming

detergent. Adding antifoam liquid into

the recovery tank before cleaning will also help

prevent foaming.

NEVER USE ACID, BLEACH or AMMONIA

9) BRUSH INSTALLATION

a) Lift the brush base by depressing the foot

level at the rear of the machine.

b) Place the brushes under the base. Align

the brush lugs with the holes in the brush

plate. Insert the brushes into the plate and

turn each brush so the lugs are pushed

toward their retaining springs, until locked.

The photo shows the directions to rotate

the brushes to lock them into operating

position.

Vacuum

Cove

Squeegee

Hose

Solution Tank

Fill O

enin

Page 8 of 35

MACHINE OPERATION

1) Connect machine connector to the battery

connector.

2) Turn on the main power key switch. Battery

charge indicator will illuminate indicating the

charge level of the batteries. If the indicator is

flashing the batteries need to be charged.

3) Turn on the brush motor switch. Please note

that the scrubbing brush will not rotate until

the hand switch lever is engaged.

4) Turn on the water solenoid valve switch.

5) Turn on the vacuum motor switch.

6) Adjust the flow rate of the cleaning solution

with lever. Moving the solution flow control

lever downward increase the flow rate and

raising the lever decreases the flow rate.

There should be enough solution to wet the

floor uniformly, but not so much thatthe water

gets past the splash guard. Remember that

the correct solution quantity depends on the

type of floor, the dirt level and the scrubbing

speed.

7) Release parking brake by raising parking

brake lever.

8) Release and raise the brush base lift lever to

lower the brush base.

9) Lower the squeegee using the squeegee lift

lever.

Machine

Connecto

Battery

Connecto

Squeegee

Lift Leve

Brush

Base

Lift

Leve

Solution

Flow

Control

Lever

Parking Brake

Leve

Solution

Tank

Drain

Hose

Vacuum

Motor

Switch

Water

Solenoid

Switch

Battery

Charge

Indicator

Brush Motor

Switch

Main Power

Key Switch

Page 9 of 35

MACHINE OPERATION

10)SCRUBBING

This machine is equipped with brush assist

propulsion. Depress the handle switch lever.

The scrub brush will begin to rotate and solution

will begin to flow. During the first few yards of

operation, check that the quantity of the cleaning

solution is sufficient to wet the floor and that the

squeegee dries the floor surface.

WARNING! Always lift the squeegee when

moving backwards.

11)OVER FILL PROTECTION

The machine is equipped with a float that stops

the vacuum exhaust air flow when the recovery

tank is full. Vacuum motor does not stop

operating but the vacuum exhaust air flow rate is

greatly reduced. When this occurs, empty the

recovery tank by removing the drain plug on the

drain hose and then empty the recovery tank.

WARNING! Use gloves for protection from

contact with dangerous solutions.

Drain Plug

Float

Handle

Switch

Lever

Page 10 of 35

UPON COMPLETION OF MACHINE USE

After finishing your work and before any type of

maintenance is done, it is necessary to do the

following:

1) Close the water valve by raising the solution

flow control lever.

2) Raise the brush base by stepping down

locking the brush base lift lever. To lock the

lever move your foot to the right while the

lever is pressed down.

3) Lock parking brake by stepping down on

parking brake lever. To lock the lever move

your foot to the right while the lever is pressed

down.

4) Lift the squeegee by raising the squeegee lift

lever and locking it by moving the lever to the

left.

WARNING! The squeegee blades can

be damaged if the squeegee is not raised

during storage or transport.

5) Switch off main power key switch.

6) Switch off the water solenoid valve switch.

7) Switch off the brush motor switch.

8) Switch off the vacuum motor switch.

9) Transport the machine to the location where

the recovery tank should be emptied.

10)Remove the drain hose at the front of the

recovery tank.

11)Remove the drain plug and empty the

recovery tank.

WARNING! Use gloves for protection

from contact with dangerous solutions.

12)Remove the brush or pad driver and clean

them with clear water.

Squeegee

Lift Leve

Brush

Base

Lift

Lever

Solution

Flow

Control

Lever

Parking Brake

Leve

Drain Plug

Solution

Tank

Drain

Hose

Vacuum

Motor

Switch

Water

Solenoid

Switch

Battery

Charge

Indicator

Brush Motor

Switch

Main Power

Key Switch

Inhaltsverzeichnis

Andere Pacific Bodenreinigungsmaschine Handbücher

Pacific

Pacific Proteus 26 Installations- und Betriebshandbuch

Pacific

Pacific SANISWEEP Installations- und Betriebshandbuch

Pacific

Pacific FURY 20BB Installations- und Betriebshandbuch

Pacific

Pacific Proteus 210E Installations- und Betriebshandbuch

Pacific

Pacific 535401 Bedienungsanleitung

Pacific

Pacific TIGERRAY 21 Installations- und Betriebshandbuch

Pacific

Pacific FURY 21 HSB Installations- und Betriebshandbuch

Pacific

Pacific Floormaster 18B Installations- und Betriebshandbuch

Pacific

Pacific 2000 DCP Installations- und Betriebshandbuch

Pacific

Pacific pro 7r Installations- und Betriebshandbuch

Pacific

Pacific FURY 1500P Bedienungsanleitung

Pacific

Pacific FM-ME Bedienungsanleitung

Pacific

Pacific Floormaster 18B Installations- und Betriebshandbuch

Pacific

Pacific FM-17EHD Bedienungsanleitung

Pacific

Pacific B-1500 Bedienungsanleitung

Pacific

Pacific B-1500 Bedienungsanleitung

Pacific

Pacific MINISWEEP Installations- und Betriebshandbuch

Pacific

Pacific FM-17EHD Bedienungsanleitung

Pacific

Pacific ScrubMaster 32B Bedienungsanleitung

Pacific

Pacific B-1500 Bedienungsanleitung

Pacific

Pacific FM-17 EHD Bedienungsanleitung

Pacific

Pacific Z26T Bedienungsanleitung

Pacific

Pacific Z20T Bedienungsanleitung

Pacific

Pacific FURY 1500DCP Bedienungsanleitung

Beliebte Bodenreinigungsmaschine Handbücher anderer Marken

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Bedienungsanleitung

Numatic

Numatic ET 4045 Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Bedienungsanleitung

Mytee

Mytee 8070 Mytee-Lite Bedienungsanleitung

Kärcher

Kärcher B 140 R Bedienungsanleitung

Triple S

Triple S Ace 26T1 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW 750 Bedienungsanleitung

Tornado

Tornado Marathon 2000 98190 Handbuch

Windsor

Windsor ADMIRAL Admiral 8 Bedienungsanleitung

Numatic

Numatic TTB 1117/100 Bedienungsanleitung

Tennant

Tennant 8210D Bedienungsanleitung

Nobles

Nobles Frontier Produkthandbuch

lavina

lavina 21-X Bedienungsanleitung

KENT

KENT Edge 28B Bedienungsanleitung

Tennant

Tennant 215 Produkthandbuch

Windsor

Windsor BDP 51/2000C Bedienungsanleitung

CleanFreak

CleanFreak DURA-18HD Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Administratorhandbuch