Panasonic EX-Z Series Bedienungsanleitung

Ultra-minute Photoelectric Sensor

EX-Z Series

USER’S MANUAL

WUME-EXZ-1

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Contens

1. Cautions··························································································3

2. Part Description ················································································4

3. Mounting ·························································································5

3-1 Mounting of sensor················································································· 5

3-2 Installation interval ················································································· 7

4. I/O Circuit Diagram············································································9

5. Stability Indicator·············································································10

6. Beam Alignment·············································································· 11

7. Option···························································································12

7-1 Sensor mounting bracket········································································12

8. Specications ·················································································13

8-1 Side sensing type ·················································································13

8-2 Front sensing type ················································································14

9. Dimensions····················································································15

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

1. Cautions

WARNING

●Never use this product as a sensing device for personnel protection.

●When using sensing devices for personnel protection, use products that meet laws

and standards, such as OSHA, ANSI or IEC etc., for personnel protection applicable in

each region or country.

●This product has been developed / produced for industrial use only.

●This product employs a small cable of 0.1mm2in conductor area. Take care that the

cable is not pulled with a strong force, as it may damage this product or break its wires.

●Make sure that stress by forcible bend or pulling is not applied to the sensor cable joint.

●

Cable can be extended up to 50m in total length (each emitter / receiver of thru-beam

type) if extension cable is more than 0.3mm2in electric conductor cross-sectional area.

●Make sure that the power supply is OFF while adding or removing the controllers.

●Take note that incorrect wiring will damage the sensor.

●Verify that the supply voltage variation is within the rating.

●If power is supplied from a commercial switching regulator, ensure that the frame ground

(F.G.) terminal of the power supply is connected to an actual ground.

●When noise generating equipment (switching regulator, inverter motor, etc.) is used in

the vicinity of this product, connect the frame ground (F.G.) terminal of the equipment to

an actual ground.

●Do not run the wires together with high-voltage lines or power lines or put them in the

same raceway. This can cause malfunction due to induction.

● Take care that the sensor is not directly exposed to uorescent lamp from a rapid-starter

lamp, a high frequency lighting device or sunlight etc., as it may affect the sensing per-

formance.

●Do not use during the initial transient time (50ms) after the power supply is switched

ON.

●This product is suitable for indoor use only.

●Avoid dust, dirt, and steam.

●Do not use this sensor in places where it may come in contact with corrosive gas, etc.

●Ensure that the product does not come into contact with organic solvents such as thin-

ner.

●Ensure that the product does not come into contact with strong acid or alkaline.

●Ensure that the product does not come into contact with oil or grease.

●This product cannot be used in an environment containing inflammable or explosive

gases.

●Never disassemble or modify the product.

●Cable end has not been waterproofed. Do not use the product in any manner that may

cause water entry via cable end.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

2. Part Description

Thru-beam emitter side sensing type EX-Z11□, EX-Z12□, EX-Z13□

Beam emitting part

Thru-beam receiver side sensing type EX-Z11□, EX-Z12□, EX-Z13□

Operation indicator (Orange)

Lights up when the sensing output

is ON.

Beam receiving part

Stability indicator (Green)

Lights up under the stable light condition

or the stable dark condition

Thru-beam emitter front sensing type EX-Z11F□, EX-Z12F□, EX-Z13F□

Beam emitting part

Thru-beam receiver front sensing type EX-Z11F□, EX-Z12F□, EX-Z13F□

Operation indicator (Orange)

Lights up when the sensing

output is ON.

Beam receiving part

Stability indicator (Green)

Lights up under the stable light condition

or the stable dark condition

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

3. Mounting

3-1 Mounting of sensor

●The tightening torque should be 0.2N·m or less.

● M2 screw and nut, spring washer, and at washer are accessory of this product.

When tapping in mounting section (Unit: mm)

Sensing

direction

8.5

M2 screw (length 10)

(accessory)

M2×0.4

Tapping depth: 5

Sensing

direction 8.5

M2 screw (length 6)

(accessory)

M2×0.4

Tapping depth: 7

When using screws and nuts that are accessory of the product (Unit: mm)

Sensing

direction

8.5

M2 screw (length 10)

(accessory) Thickness of mounting

plate: 2 or less

Nut

Spring washer

Flat washer

Thickness of mounting

plate: 2 or less

Nut

Spring washer

Flat washer

Sensing

direction 8.5

M2 screw (length 6)

(accessory)

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

When using sensor mounting bracket (optional)

L-shaped mounting bracket

MS-EXZ-1 Mounting bracket for front sensing type

MS-EXZ-2

Mounting spacer for front sensing type

MS-EXZ-4

Mounting bracket for side sensing type

MS-EXZ-3

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

3-2 Installation interval

●Interference prevention function is not incorporated in this product. In case mounting two

sets of this product close together, please mount it as drawing below indicates. (Typical

example)

● Find out the operating point ℓ1 on the parallel deviation diagram for the sensing distance

L1. Separate sensors by 2 X ℓ1 or more.

EX-Z11□, EX-Z11F□

010 1020 20

Operation distance ℓ(mm)

CenterLeft Right

(L1)

(ℓ1)

Sensing distance L (mm)

In case using at sensing distance (L1) 50mm, the

operation point (ℓ1) is approx. 8.02mm according

to diagram above.

The installation interval is

Approx. 8.02mm X 2 = approx. 16.04mm

Thus, install the product to approx. 16.04mm or

more away.

50mm

16.04mm

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

EX-Z12□, EX-Z12F□

200

100

050 50100 100

Operation distance ℓ(mm)

CenterLeft Right

(L2)

(ℓ2)

Sensing distance L (mm)

In case using at sensing distance (L2) 200mm, the

operation point (ℓ2) is approx. 30.5mm according

to the diagram at left.

The installation interval is

Approx. 30.5mm X 2 = approx. 61mm

Thus, install the product to approx. 61mm or more

away.

200mm

61mm

EX-Z13□, EX-Z13F□

800

400

600

200

050 50100 100

Operation distance ℓ(mm)

CenterLeft Right

(L3)

(ℓ3)

Sensing distance L (mm)

In case using at sensing distance (L3) 500mm, the

operation point (ℓ3) is approx. 81.9mm according

to the diagram at left.

The installation interval is

Approx. 81.9mm X 2 = approx. 163.8mm

Thus, install the product to approx. 163.8mm or

more away.

500mm

163.8mm

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

4. I/O Circuit Diagram

NPN output type and PNP output type common: Thru-beam type emitter EX-Z1□

Main circuit

(Brown) + V

(Blue) 0V

‒

12 to 24V DC

±10%

Users’ circuitInternal circuit

NPN output type: Thru-beam type receiver EX-Z1□

Main circuit

(Brown) + V

(Black) Output

(Blue) 0V

Load

‒

12 to 24V DC

±10%

Users’ circuitInternal circuit

PNP output type: Thru-beam type receiver EX-Z1□-P

Main circuit

(Brown) + V

(Black) Output

(Blue) 0V

Load

‒

12 to 24V DC

±10%

Users’ circuitInternal circuit

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

5. Stability Indicator

●The stability indicator (green) lights up when the incident light intensity has sufficient

margin to the operation level.

When the beam is received at a level where the stability indicator lights up, stable sens-

ing is possible in both the "Light" state operation and the "Dark" state operation without

being affected by changes in temperature, voltage, etc.

Approx.

15%

Approx.

25%

100

Lights up

Turned off

"Light" state operation

"Dark" state operation

Lights up

Output operation level

Light margin width

Dark margin width

Output operation

Stability indicator operation

Sensing distance

Incident light intensity (%)

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Inhaltsverzeichnis

Andere Panasonic Zubehör Handbücher

Panasonic

Panasonic HL-G1-A-C5 Series Bedienungsanleitung

Panasonic

Panasonic SR-HBA101 Bedienungsanleitung

Panasonic

Panasonic MA2DF31 Bedienungsanleitung

Panasonic

Panasonic SR-CN108 Bedienungsanleitung

Panasonic

Panasonic LS-H Series Bedienungsanleitung

Panasonic

Panasonic EX-F70 SERIES Bedienungsanleitung

Panasonic

Panasonic MA3S133 (MA133) Bedienungsanleitung

Panasonic

Panasonic EQ-34 Bedienungsanleitung

Panasonic

Panasonic MA2SP01 Bedienungsanleitung

Panasonic

Panasonic EX-F60 SERIES Bedienungsanleitung

Panasonic

Panasonic MA3J7420G Bedienungsanleitung

Panasonic

Panasonic Schottky Barrier Diodes MA3X721 (MA721) Bedienungsanleitung

Panasonic

Panasonic EQ-500 Series Bedienungsanleitung

Panasonic

Panasonic MA4X746 (MA746) Bedienungsanleitung

Panasonic

Panasonic HL-C211F5 Bedienungsanleitung

Panasonic

Panasonic KX-HNS101 Bedienungsanleitung

Panasonic

Panasonic MA4SD05X Bedienungsanleitung

Panasonic

Panasonic SF-C14EX Bedienungsanleitung

Panasonic

Panasonic MA3X787 (MA787) Bedienungsanleitung

Panasonic

Panasonic MQ-W3A-DC12-24VEM Bedienungsanleitung

Panasonic

Panasonic FZ-VNPN11U Bedienungsanleitung

Panasonic

Panasonic MA3X703 Bedienungsanleitung

Panasonic

Panasonic MA2SP02 Bedienungsanleitung

Panasonic

Panasonic MKG1301913 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Bedienungsanleitung