Panasonic FP0-TC4 Bedienungsanleitung

Safety Precautions

Observe the following notices to ensure personal safety or to prevent accidents.

To ensure that you use this product correctly, read this User’s Manual thoroughly before use.

Make sure that you fully understand the product and information on safety.

This manual uses two safety flags to indicate different levels of danger.

WARNING

If critical situations that could lead to user’s death or serious injury is assumed by

mishandling of the product.

-Always take precautions to ensure the overall safety of your system, so that the whole

system remains safe in the event of failure of this product or other external factor.

-Do not use this product in areas with inflammable gas. It could lead to an explosion.

-Exposing this product to excessive heat or open flames could cause damage to the lithium

battery or other electronic parts.

CAUTION

If critical situations that could lead to user’s injury or only property damage is

assumed by mishandling of the product.

-To prevent excessive exothermic heat or smoke generation, use this product at the values

less than the maximum of the characteristics and performance that are assured in these

specifications.

-Do not dismantle or remodel the product. It could cause excessive exothermic heat or smoke

generation.

-Do not touch the terminal while turning on electricity. It could lead to an electric shock.

-Use the external devices to function the emergency stop and interlock circuit.

-Connect the wires or connectors securely.

The loose connection could cause excessive exothermic heat or smoke generation.

-Do not allow foreign matters such as liquid, flammable materials, metals to go into the inside

of the product. It could cause excessive exothermic heat or smoke generation.

-Do not undertake construction (such as connection and disconnection) while the power

supply is on. It could lead to an electric shock.

-This manual and its contents are copyrighted.

-You may not copy this manual, in whole or part, without written consent of Panasonic Electric

Works SUNX Co., Ltd.

-Windows is a registered trademark of Microsoft Corporation in the United States and other

countries.

-All other company names and product names are trademarks or registered trademarks of

their respective owners.

PLC_ORG

Table of Contents

Precautions before Usage

1 Unit Outlines................................................................................................................................. 1

1.1 Functions..................................................................................................................................................... 1

1.2 Model........................................................................................................................................................... 1

1.3 Unit Connection Limit .................................................................................................................................. 1

2 Part Names and Functions.......................................................................................................... 2

3 Input Range Setting Switch ........................................................................................................ 3

4 Wiring............................................................................................................................................ 4

5 Conversion Characteristic .......................................................................................................... 6

6 What is Averaging ? .................................................................................................................... 8

7 I/O Allocations and Program....................................................................................................... 9

7.1 I/O No. ......................................................................................................................................................... 9

7.2 Program..................................................................................................................................................... 10

8 When Error Occurred ................................................................................................................ 13

8.1 What to Do................................................................................................................................................. 13

8.2 Digital Value when Out of Range .............................................................................................................. 13

9 Specifications............................................................................................................................. 14

9.1 Specifications............................................................................................................................................. 14

9.2 Dimensions................................................................................................................................................ 17

Precautions before Usage

- Accuracy

・ Connecting/disconnecting the Thermocouple input terminal block while the Thermocouple Unit is ON will

lower an accuracy temporarily. Accordingly, use the temperature data obtained 15 minutes after its action.

・ When a high-accurate temperature data is required, use the temperature data obtained 15 minutes after

turning ON the Thermocouple Unit. (However, the temperature data within 15 minutes is also within the

Total accuracy range.)

・A rapid temperature change in the Thermocouple Unit might change the temperature data temporarily.

・ The direct air (wind) from the cooling fan built in the control panel etc. to the Thermocouple Unit will lower

an accuracy. Prevent a direct air.

- Programming

・ From the Power-ON to the converted data Ready, the digital value will be K8001 or K16001. Create a

ladder program not to use the data obtained during that period.

・ When the thermocouple is broken, the digital value will change to K8000 or K16000 within 70 seconds.

Practice in the ladder program a process for avoiding a risk, would be resulting from a broken thermocouple,

and exchange the thermocouple.

・ When the Input range setting switch is set for 4 channels or more, use a program described in “7.2

Program>, without fail.

1 Unit Outlines

1.1 Functions

1. Thermocouple input unit for FP0/FPΣControl Unit

The temperature data obtained using the thermocouple is converted to the digital value to be read into the

FP0/ FPΣControl Unit.

2. Thermocouple types K, J, T and R are available.

3. 3 temperature measurement ranges are available.

-100.0 to +500.0 (Thermocouple types: K and J)

-100.0 to +400.0 (Thermocouple type : T)

0.0 to +1500.0 (Thermocouple type : R)

4. The data can be converted to the degree Celsius or the degree Fahrenheit.

The temperature data measured using the sensor is converted to the degree Celsius or the degree

Fahrenheit inside the Thermocouple Unit.

5. The averaging function is installed.

The converted data (degree Celsius or Fahrenheit) is averaged, so that even unstable input signals can

be properly read.

6. The broken-thermocouple detector is attached.

A thermocouple, broken, can be detected.

1.2 Model

-Thermocouple Unit

Part number Thermocouple

input points Product number

FP0-TC4 4 points AFP0420

FP0-TC8 8 points AFP0421

1.3 Unit Connection Limit

- Number limit

Up to 3 expansion units can be connected with the Control Unit.

- Position limit

Install the thermocouple unit on the right side of other expansion unit. If it is installed on the left side, the

total

precision will deteriorate.

Reference: “7.1 I/O No.”.

2 Part Names and Functions

- Thermocouple Unit

①Input range setting switch

changes between the input ranges (thermocouple types). Only the same range setting is available for all

the 8 channels. (The setting can not be specified per channel.)

Reference: “4 Input Range Setting Switch”.

②Thermocouple input terminal block (9-pin)

is made by Phoenix. Model No. is MC1.5/9-ST-3.5 (Part No.: 1840434)

Suitable wires

Size Nominal cross-sectional area

AWG# 28 to 16 0.08 mm2to 0.25mm2

Reference: FP0 Hardware Manual “Wiring the Terminal Type”.

FP∑User’s Manual “Wiring of Terminal Block Type”.

③Expansion connector

Connects the expansion unit to the internal circuit of the Control Unit.

Reference: FP0 Hardware Manual “Adding Expansion Units”.

FP∑User’s Manual “Expansion Method of Units for FP0 and FP∑”.

④DIN rail attachment lever (One-touch hook)

The unit can be installed to the DIN rail through one-touch operation.

This is also used for installing the unit to the FP0 Slim Type Mounting Plate (AFP0803).

⑤Expansion hook

Fixes the expansion unit with the Control Unit.

3 Input Range Setting Switch

-Input range setting switch

OFF

MODE

(The following switch settings are read once when the Control Unit is turned ON. Any change will not be

reflected even if made while ON.)

1) Input range setting switch

OFF ON OFF ON OFF ON OFF ON

MODE SW 1

Thermocouple type K J T R

2) Temperature unit switch

OFF ON OFF ON

MODE SW 3

Unit ℃℉

3) Input channel selection switch

OFF ON OFF ON OFF ON OFF ON

MODE SW 4

Input channel CH0, 1 CH0 to CH3 CH0 to CH5 CH0 to CH7

Number of input

channels 2 4 6 * 8 *

* Do not specify it for the FP0-TC4.

4 Wiring

-Wiring method

-Input line wiring

・Keep the space more than 100mm between the input line and the power line/high-voltage line.

・It is recommended grounding the unit using the insulated compensating wire.

- Input terminal block

Pin No. Name Function

1 CH.0 + CH0 + thermocouple input

2 CH.0 - CH0 - thermocouple input

3 CH.1 + CH1 + thermocouple input

4 CH.1 - CH1 - thermocouple input

5 CH.2 + CH2 + thermocouple input

6 CH.2 - CH2 - thermocouple input

7 CH.3 + CH3 + thermocouple input

8 CH.3 - CH3 - thermocouple input

9 NC no connection

1 CH.4 + CH4 + thermocouple input

2 CH.4 - CH4 - thermocouple input

3 CH.5 + CH5 + thermocouple input

4 CH.5 - CH5 - thermocouple input

5 CH.6 + CH6 + thermocouple input

6 CH.6 - CH6 - thermocouple input

7 CH.7 + CH7 + thermocouple input

8 CH.7 - CH7 - thermocouple input

9 NC no connection

* Where between channels are insulated using the PhotoMos relay.

5 Conversion Characteristic

-K and J range (-100.0℃to 500.0℃)-T range (-100.0℃to 400.0℃)

When the input out of the range is made When the input out of the range is made

Input converted to Input converted to

-100.1℃Max. K -1001 - 100.1℃Max. K -1001

500.1℃Min. K 5001 or K 8000 400.1℃Min. K 4001 or K 8000

When the thermocouple

is broken K 8000 When the thermocouple

is broken K 8000

- R range (0.0℃to 1500.0℃)

When the input out of the range is made

Input converted to

0.0℃Max. K 0

1500.1℃Min. K 15001 or K 16000

When the thermocouple

is broken K 16000

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Controller Handbücher

Panasonic

Panasonic AW-RP60G Bedienungsanleitung

Panasonic

Panasonic SQ4-C11 Bedienungsanleitung

Panasonic

Panasonic FP-XH Series Bedienungsanleitung

Panasonic

Panasonic MINAS S-series Bedienungsanleitung

Panasonic

Panasonic FP0R Series Bedienungsanleitung

Panasonic

Panasonic FP7 Series Bedienungsanleitung

Panasonic

Panasonic MGSDB2 Series Bedienungsanleitung

Panasonic

Panasonic CZ-256ESMC1U Bedienungsanleitung

Panasonic

Panasonic AF7CPS Series Bedienungsanleitung

Panasonic

Panasonic DPC-100 Series Bedienungsanleitung

Panasonic

Panasonic WVCU161C - SYSTEM CONTROLLER Bedienungsanleitung

Panasonic

Panasonic AG-A571 Bedienungsanleitung

Panasonic

Panasonic FP2-PP2T Bedienungsanleitung

Panasonic

Panasonic TY-FB12LC Bedienungsanleitung

Panasonic

Panasonic FP7 Series Bedienungsanleitung

Panasonic

Panasonic FP-M Hardware Bedienungsanleitung

Panasonic

Panasonic WVCU161C - SYSTEM CONTROLLER Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Panasonic

Panasonic FP Web-Server2 Bedienungsanleitung

Panasonic

Panasonic EYFLA7AR Betriebsanleitung

Panasonic

Panasonic EYFR03 Einrichtungshandbuch

Panasonic

Panasonic FP7 Series Installationshandbuch

Panasonic

Panasonic CZ-256ESMC3 Bedienungsanleitung

Panasonic

Panasonic FP (Sigma) Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung