Panasonic S-Link FP2 Bedienungsanleitung
Safety Precautions
Observe the following notices to ensure personal safety or to prevent accidents.
To ensure that you use this product correctly, read this User’s Manual thoroughly before use.
Make sure that you fully understand the product and information on safety.
This manual uses two safety flags to indicate different levels of danger.
WARNING
If critical situations that could lead to user’s death or serious injury is assumed by
mishandling of the product.
-Always take precautions to ensure the overall safety of your system, so that the whole
system remains safe in the event of failure of this product or other external factor.
-Do not use this product in areas with inflammable gas. It could lead to an explosion.
-Exposing this product to excessive heat or open flames could cause damage to the lithium
battery or other electronic parts.
CAUTION
If critical situations that could lead to user’s injury or only property damage is
assumed by mishandling of the product.
-To prevent excessive exothermic heat or smoke generation, use this product at the values
less than the maximum of the characteristics and performance that are assured in these
specifications.
-Do not dismantle or remodel the product. It could cause excessive exothermic heat or smoke
generation.
-Do not touch the terminal while turning on electricity. It could lead to an electric shock.
-Use the external devices to function the emergency stop and interlock circuit.
-Connect the wires or connectors securely.
The loose connection could cause excessive exothermic heat or smoke generation.
-Do not allow foreign matters such as liquid, flammable materials, metals to go into the inside
of the product. It could cause excessive exothermic heat or smoke generation.
-Do not undertake construction (such as connection and disconnection) while the power
supply is on. It could lead to an electric shock.
Copyright / Trademarks
-This manual and its contents are copyrighted.
-You may not copy this manual, in whole or part, without written consent of Panasonic
Industrial Devices SUNX Co., Ltd.
-Windows is a registered trademark of Microsoft Corporation in the United States and other
countries.
-All other company names and product names are trademarks or registered trademarks of
their respective owners. PLC_ORG
IntroductionFP2 S−LINK Unit
i
Introduction
Thank you for purchasing the FP2 S−LINK unit/CPU with S−LINK.
The FP2 S−LINK unit is designed exclusively for the FP2 programmable controller, and
is equipped with numerous functions that make it easy to use the S−LINK with the FP2.
This hardware manual describes the functions, installation, wiring, and operation of the
FP2 S−LINK unit/CPU with S−LINK.
Please make sure you understand the material contained in this manual before using
your equipment.
Table of Contents FP2 S−LINK Unit
ii
Table of Contents
Special Precautions iv................................................
Chapter 1 Selecting the Right Equipment
1.1 Features 1 −3.........................................................
1.2 Types 1 −5............................................................
1.3 Installation Restrictions 1 −6............................................
1.3.1 FP2 S−LINK Unit 1 −6..........................................
1.3.2 CPU with S−LINK 1 −7.........................................
1.4 Current Consumption 1 −8..............................................
Chapter 2 Specifications
2.1 Parts Related to S−LINK Operation 2 −3..................................
2.2 Parts Related to CPU Operation (CPU with S−LINK) 2 −7...................
2.3 Specifications 2 −8.....................................................
2.4 S−LINK Controller Specifications 2 −9....................................
Chapter 3 I/O Assignments
3.1 An Overview of I/O Assignments 3 −3....................................
3.2 Specifying the Number of Input/Output Points 3 −4.........................
3.3 Assigning Inputs and Outputs 3 −8.......................................
3.3.1 User−Determined Assignments 3 −8..............................
3.3.2 I/O Mounting Assignments 3 −9..................................
3.3.3 Automatic Assignments 3 −9....................................
3.4 Slot of CPU with S−LINK 3 −10.........................................
Chapter 4 Construction and Wiring
4.1 Wiring Methods for S−LINK Main Unit 4 −3................................
4.1.1 Wiring to the S−LINK Terminal Block 4 −3.........................
4.1.2 Standard Wiring 4 −4...........................................
4.1.3 Loop Wiring 4 −5...............................................
4.2 S−LINK Main Power Supply 4 −6........................................
Chapter 5 Operation
5.1 Starting Operation 5 −3.................................................
Table of Contents
FP2 S−LINK Unit
iii
5.2 Ending Operation 5 −5.................................................
5.3 Timing 5 −6...........................................................
5.4 S−LINK I/O Device Address Recognition 5 −7.............................
5.4.1 Recognizing the Address 5 −7...................................
5.4.2 For a CPU With S−LINK 5 −8....................................
5.4.3 What to do if an Error Occurs 5 −8...............................
5.4.4 Results and Processing of Address Recognition 5 −9...............
5.4.5 Confirming Connected Stations 5 −10............................
5.4.5.1 Confirming All Recognized Addresses 5 −10...........
5.4.5.2 Confirming All Addresses Where Errors Have
Occurred 5 −12.....................................
5.4.5.3 Confirming the On/Off Status of Addresses 5 −13.......
Chapter 6 Shared Memory
6.1 Configuration of the Shared Memory 6 −3.................................
6.2 Shared Memory Reading Program 6 −4...................................
Chapter 7 What To Do If An Error Occurs
7.1 Judging Errors From the Error Indicators 7 −3.............................
7.1.1 ERR1 is Lighted 7 −3...........................................
7.1.2 ERR1 and ERR3 are Lighted 7 −4................................
7.1.3 ERR4 is Lighted 7 −4...........................................
7.2 Address Display 7 −5..................................................
7.3 Judging Error Displays 7 −6.............................................
7.3.1 Only a Numeric Value is Displayed 7 −6...........................
7.3.2 A Numeric Value and Decimal Points are Displayed 7 −6............
Chapter 8 Appendix
8.1 Table of Shared Memory Addresses 8 −3.................................
8.1.1 Error Address Quick Reference Table 8 −5........................
8.1.2 Connection Unit Address Quick Reference Table 8 −5..............
8.2 S−LINK Address Quick Reference Table 8 −6.............................
Record of changes R−1..............................................
Special Precautions FP2 S−LINK Unit
iv
Special Precautions
This manual is the instruction manual for the FP2 S−LINK unit/CPU with S−LINK.
For detailed information about the S−LINK, refer to the “S−LINK Design manual and
Construction manual.”
Chapter 1
Selecting the Right Equipment
1.1 Features 1 −3.......................................
1.2 Types 1 −5..........................................
1.3 Installation Restrictions 1 −6..........................
1.3.1 FP2 S−LINK Unit 1 −6........................
1.3.2 CPU with S−LINK 1 −7.......................
1.4 Current Consumption 1 −8............................
Selecting the Right Equipment FP2 S−LINK Unit
1−2
FP2 S−LINK Unit Selecting the Right Equipment
1−3
1.1 Features
1.1 Features
Two methods of wiring may be employed, depending on the application: standard wiring
or loop wiring.
Example: Standard wiring
In this method, wiring is done from the control section using
an S−LINK exclusive flat cable and an end hook−up connector
is connected at the end of the main cable. The maximum cable
length is 200 meters (400 meters if a booster is used).
End hook−up
connector
Control section
S−LINK exclu-
sive flat cable
Maximum length: 200 m (400 m when a booster is used)
S−LINK I/O device
Branch
cable
’T’−branch
hook−up
connector
‘T’−branch hook−up
connector
Example: Loop wiring
The S−LINK exclusive flat cable from is run from the controller,
and the end is connected back to the controller. The loop can
have a maximum length of 200 meters. The end connector is
connected at approximately the mid−point of the loop (the
position furthest from the S−LINK unit). Even if the main
signal/power line is broken at one point, the system does not
go down and signal transmission continues.
‘T’−branch hook−up
connector
End
hook−up
connector
S−LINK I/O device
next page
Selecting the Right Equipment FP2 S−LINK Unit
1−4
1.1 Features
•A built−in S−LINK controller is provided for coupling directly to the
S−LINK. This enables wiring for expansion inputs and outputs
points to be neat and efficient.
•The user may select combinations offering up to a total of 128
inputs and outputs.
•For the CPU with S−LINK, two internal S−LINK controllers are
provided, and two input/output channels (128 points x 2) can be
used.
•The inputs and outputs are handled by the program just like
ordinary ones.
•The S−LINK system can be easily monitored by reading shared
memory data.
•A broad range of peripheral devices for the S−LINK enable easy
system configuration.
Andere Handbücher für S-Link FP2
1
Inhaltsverzeichnis
Andere Panasonic Controller Handbücher
Panasonic
Panasonic CZ-RD516C-1 Bedienungsanleitung
Panasonic
Panasonic AFP7CPS Series Bedienungsanleitung
Panasonic
Panasonic Vossloh-Schwabe Light Controller IP/DALI 2CH Bedienungsanleitung
Panasonic
Panasonic FP7 Series Bedienungsanleitung
Panasonic
Panasonic WVCU161C - SYSTEM CONTROLLER Bedienungsanleitung
Panasonic
Panasonic AW-RP60GJS Bedienungsanleitung
Panasonic
Panasonic AFPXHEAD4 Bedienungsanleitung
Panasonic
Panasonic S-LINK V Bedienungsanleitung
Panasonic
Panasonic AFP7PSA1 Bedienungsanleitung
Panasonic
Panasonic FP3 Bedienungsanleitung
Panasonic
Panasonic AW-HHD100E Bedienungsanleitung
Panasonic
Panasonic FP7 Series Bedienungsanleitung
Panasonic
Panasonic FP0-TC4 Bedienungsanleitung
Panasonic
Panasonic AWLK30 - LENS CONTROLLER Bedienungsanleitung
Panasonic
Panasonic AGA96 - VCR ACC Bedienungsanleitung
Panasonic
Panasonic CZ-ANC2 Bedienungsanleitung
Panasonic
Panasonic CF-VEBC11U Bedienungsanleitung
Panasonic
Panasonic DPS-400 Series Bedienungsanleitung
Panasonic
Panasonic FV-WCCS1-W Bedienungsanleitung
Panasonic
Panasonic FP? Positioning Unit RTEX Bedienungsanleitung
