Panasonic KX-UTG200 Bedienungsanleitung

Getting Started

SIP Phone

Model No. KX-UTG200

KX-UTG300

Document Version: 2014-04

Thank you for purchasing this Panasonic product.

Please read this manual carefully before using this product and save this manual for

future use.

Note

• In this manual, most illustrations shown are based on the KX-UTG200.

Outline

This manual briey describes basic information about the installation of the unit.

Related Documentation

Operating Instructions

Describes information about the installation and operation of the unit.

Administrator Guide

Describes information about the programming and maintenance of the unit.

These manuals and supporting information are provided on the Panasonic Web site

at:

http://www.panasonic.com/sip

Other Information/For Your Safety

Other Information

Open Source Software Notice

Parts of this product use open source software. For details about the open source

software, see the Operating Instructions.

Trademarks

• Plantronics is a trademark or registered trademark of Plantronics, Inc.

• Jabra is a registered trademark of GN Netcom A/S.

• The Bluetooth® word mark and logos are registered trademarks owned by

the Bluetooth SIG, Inc. and any use of such marks by Panasonic System

Communications Company of North America is under license.

• All other trademarks identied herein are the property of their respective owners.

For Your Safety

To reduce the risk of injury, loss of life, electric shock, re, malfunction, and damage

to equipment or property, always observe the following safety precautions.

Explanation of symbols

The following symbols are used to classify and describe the level of hazard and

injury caused when the denotation is disregarded and improper use is performed.

WARNING Denotes a potential hazard that could

result in serious injury or death.

CAUTION Denotes a hazard that could result in

minor injury or damage to the unit or other

equipment.

The following symbols are used to classify and describe the type of instructions to be

observed.

This symbol is used to alert users to a specic operating procedure that

must not be performed.

This symbol is used to alert users to a specic operating procedure that

must be followed in order to operate the unit safely.

For Your Safety

WARNING

General Safety

Do not disassemble this unit. Dangerous electrical shock could result.

The unit must only be disassembled and repaired by qualied service

technicians.

Never attempt to insert wires, pins, etc. into the vents or other holes of

this unit.

To prevent possible re or electric shock, do not expose this unit to rain or

moisture.

Do not splash water on the AC adaptor or the power cord, nor get them

wet. Doing so can result in re, electric shock, or injury. If they do get wet,

immediately disconnect the AC adaptor and power cord, and contact an

authorized service center.

Do not connect or disconnect the AC adaptor and/or the AC adaptor cord

with wet hands.

Do not touch the AC adaptor for extended periods of time. Doing so can

lead to low-degree burns.

Do not use the power cord with other products. Doing so can result in re

or electric shock.

Unplug this unit from the AC outlet and have the unit serviced by qualied

service personnel in the following cases:

A. When the power supply cord or plug is damaged or frayed.

B. If liquid has been spilled on the unit.

C. If the unit has been exposed to rain or water.

D. If the unit does not work normally by following the manual. Adjust only

controls covered by the manual. Improper adjustment may require

repair by an authorized service center.

E. If the unit has been dropped, or damaged.

F. If the unit's performance deteriorates.

For Your Safety

If damage to the unit exposes any internal parts, immediately disconnect

the cable or cord. If the power is supplied from the network to the SIP

Phone [Power-over-Ethernet], disconnect the Ethernet cables. Otherwise,

disconnect the AC adaptor cord. Then return this unit to an authorized

service center.

This handset earpiece is magnetized and may retain small ferrous

objects.

The use of excessive sound volume through earphones, headphones, or

headsets may cause hearing loss.

Disconnect this unit from power outlet/the Ethernet cables if it emits

smoke, an abnormal smell, or makes unusual noise. These conditions can

cause re or electric shock. Conrm that smoke has stopped and contact

an authorized service center.

Installation

Do not make power connections that exceed the ratings for the AC outlet

or power equipment. If the power rating of a surge protector, etc. is

exceeded, it can cause a re due to heat buildup.

Do not bundle up the AC adaptor cord. The cord may become damaged,

which can lead to a re, electric shock, or electric short.

The unit should only be connected to a power supply of the type as shown

on the label on the unit.

Completely insert the AC adaptor into the AC outlet. Failure to do so may

cause electric shock and/or excessive heat resulting in a re.

Medical (KX-UTG300 only)

Do not use the product in health care facilities if any regulations posted in

the area instruct you not to do so. Hospitals or health care facilities may

be using equipment that could be sensitive to external RF energy.

Consult the manufacturer of any personal medical devices, such as

pacemakers or hearing aids, to determine if they are adequately shielded

from external RF (radio frequency) energy (the product operates in the

frequency range of 2.402 GHz to 2.480 GHz and the power output is 1.82

mW [max.]).

For Your Safety

Placement

Care should be taken so that objects do not fall onto, and liquids are not

spilled into, the unit. Do not subject this unit to excessive smoke, dust,

moisture, mechanical vibration, shock, or direct sunlight.

Do not place heavy objects on top of this unit.

Place this unit on a at surface.

Allow 10 cm (3 15/16 in) clearance around the unit for proper ventilation.

Wall Mounting

Make sure that the wall that the unit will be attached to is strong enough

to support the unit. If not, it is necessary for the wall to be reinforced. For

information about the weight of the unit, see the Operating Instructions.

Only use the optional wall mount kit with the unit. The wall mount kit

includes the necessary screws, washers, and wall mounting adaptor.

When driving the screws into the wall, be careful to avoid touching any

metal laths, wire laths or metal plates in the wall.

When this unit is no longer in use, make sure to detach it from the wall.

CAUTION

Keep the unit away from heating appliances and devices that generate

electrical noise, such as uorescent lamps, motors and televisions. These

noise sources can interfere with the performance of the unit. It also should

not be placed in rooms where the temperature is less than 0 ºC (32 ºF) or

greater than 40 ºC (104 ºF).

For Your Safety/Important Safety Instructions

Wipe the unit with a soft cloth. Do not clean the unit with abrasive

powders or with chemical agents such as benzine or thinner.

The handset hook poses a choking hazard. Keep the handset hook out of

reach of children.

When left unused for a long period of time, disconnect the unit from

the AC outlet. When the unit receives power from a PoE power supply,

disconnect the Ethernet cables.

When the unit is mounted on a wall, make sure the cables are securely

fastened to the wall.

Notice

•

If the unit does not operate properly, disconnect the AC adaptor cord and

Ethernet cables and then connect again.

•

If you are having problems making calls, disconnect the Ethernet cables and

connect a known working SIP Phone. If the known working SIP Phone operates

properly, have the defective SIP Phone repaired by an authorized service

center. If the known working SIP Phone does not operate properly, check the

SIP server and the Ethernet cables.

•

Under power failure conditions, the SIP Phone may not operate. Please ensure

that a separate telephone, not dependent on local power, is available for use in

remote sites in case of emergency.

•

For information regarding network setup of the SIP Phone such as IP

addresses, please see the Operating Instructions.

•

If an error message is shown on your display, consult your phone system dealer

or the network administrator.

•

External parts (the handset, cords, etc.) of the unit are not interchangeable.

Only use Panasonic brand parts.

Important Safety Instructions

When using this unit, basic safety precautions should always be followed to reduce

the risk of re, electric shock and injury to persons, including the following:

1. Do not use the unit near water, for example, near a bathtub, washbowl, kitchen

sink, or laundry tub, in a wet basement, or near a swimming pool.

2. Avoid using a telephone (other than a cordless type) during an electrical storm.

There may be a remote risk of electric shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

SAVE THESE INSTRUCTIONS

Accessory Information

Included Accessories*1

Handset (1) Handset Cord (1)

[Part No.]

95.1204T00

[Part No.]

371.00447.005

Stand (1) Ethernet cable (1)

[Part No.]

467.00209.005

[Part No.]

371.00473.005

*1 For extra orders for the accessories, call toll-free: 1-800-332-5368.

Note

• The illustrations may differ from the appearance of the actual product.

Optional Accessories

AC Adaptor

• DSA-42D-48 2 480063 (P/N: 381.00398.005)

Wall Mount Kit • KX-A433

Add-on key module • KX-UTA336

Location of Controls

Front View

For KX-UTG200:

EF G HI JK L MNOP Q R

For KX-UTG300:

F G H IJ KL MNOP Q R

Location of Controls

AHandset Hook

Keeps the handset stable when the unit is mounted on a wall.

BLCD (Liquid Crystal Display)

KX-UTG200 is equipped with a 3.5-inch color LCD and LCD backlight.

KX-UTG300 is equipped with a 5.0-inch color LCD touch screen and LCD

backlight.

CFlexible Buttons/Flexible Button Lamps (KX-UTG200 only)

Used to make or receive calls, or perform the feature that has been assigned

to the button. The exible button lamp shows the status of each exible

button.

DMessage/Ringer Lamp

When you receive a call, the lamp ashes red.

When someone has left you a message, the lamp stays on red.

ESoft Buttons (S1 to S4) (KX-UTG200 only)

S1 to S4 (located below the display) are used to select the item displayed on

the bottom line of the display.

FMESSAGE

Used to access your voice mailbox.

GVOLUME

Used to adjust the volume.

HFORWARD/DO NOT DISTURB

Used to set Call Forwarding or Do Not Disturb on your extension.

INavigator Key

Used to select desired items.

JENTER

Used to assign the selected item.

KHOME

Used to return the display to the home screen.

LSP-PHONE (Speakerphone)

Used for performing hands-free operations. When the SP-PHONE is used, its

lamp turns red.

MHEADSET

Used when using a headset. When the HEADSET is used, its lamp turns red.

NCONFERENCE

Used to establish a three-way conference.

OTRANSFER

Used to transfer a call to another party.

PMUTE

Used to mute the microphone/handset/headset during a conversation. When

the MUTE is used, its lamp turns red.

Installation and Setup

QREDIAL

Used to redial the last dialed number.

RHOLD

Used to put a call on hold.

Right Side View (for KX-UTG300)

AAdd-on Key Module Slot Cover

Remove the Add-on key module slot cover when connecting an Add-on key

module to the unit.

BUSB Port

Connect a USB headset or other USB device.

Andere Handbücher für KX-UTG200

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic IP-Telefon Handbücher

Panasonic

Panasonic KX-UT113 Bedienungsanleitung

Panasonic

Panasonic KX-TDE100 Bedienungsanleitung

Panasonic

Panasonic KX-HDV100 Service-Handbuch

Panasonic

Panasonic KX-NT400 Bedienungsanleitung

Panasonic

Panasonic KX-HDV430 Bedienungsanleitung

Panasonic

Panasonic KX-UT133 Bedienungsanleitung

Panasonic

Panasonic KX TPA 65 Bedienungsanleitung

Panasonic

Panasonic KX-TD7665 Bedienungsanleitung

Panasonic

Panasonic KX-NT321-B Bedienungsanleitung

Panasonic

Panasonic KX-UTG200 Bedienungsanleitung

Panasonic

Panasonic KX-UT133-B Bedienungsanleitung

Panasonic

Panasonic KX-TDA0350 Bedienungsanleitung

Panasonic

Panasonic KX-UT123 Bedienungsanleitung

Panasonic

Panasonic T-Mobile KX-HDV130 Bedienungsanleitung

Panasonic

Panasonic DECT Portable Station KX-TCA256 Bedienungsanleitung

Panasonic

Panasonic KX-HDV100 Service-Handbuch

Panasonic

Panasonic KX-UT113 Bedienungsanleitung

Panasonic

Panasonic KX-TD7685 - Wireless Digital Phone Bedienungsanleitung

Panasonic

Panasonic KX-UTG200 Service-Handbuch

Panasonic

Panasonic KXDT321 - DIGITAL PROPRIETARY TELEPHONE Bedienungsanleitung

Panasonic

Panasonic KX-TDA Gebrauchsanweisung

Panasonic

Panasonic TGP 550 Bedienungsanleitung

Panasonic

Panasonic KX-NT543 Bedienungsanleitung

Panasonic

Panasonic KX-TGP500 Bedienungsanleitung

Beliebte IP-Telefon Handbücher anderer Marken

Alcatel

Alcatel 4028 Bedienungsanleitung

Polycom

Polycom Polycom VVX 600 Bedienungsanleitung

Polycom

Polycom SoundPoint IP 450 Bedienungsanleitung

Cisco

Cisco SPA-500 Series Bedienungsanleitung

Polycom

Polycom SoundPoint IP 650 Bedienungsanleitung

Proximus

Proximus Maestro 3016 IP Bedienungsanleitung

Fanvil

Fanvil X4 Bedienungsanleitung

Cisco

Cisco 7962 Bedienungsanleitung

Snom

Snom 320 Bedienungsanleitung

Yealink

Yealink Yealink SIP-T46G Bedienungsanleitung

Avaya

Avaya 4625SW Bedienungsanleitung

Yealink

Yealink SIP-T52S Bedienungsanleitung

Nortel

Nortel 1140E Bedienungsanleitung

Nexotek

Nexotek NT-P500 Bedienungsanleitung

Avaya

Avaya Integral 5 R3.0 Bedienungsanleitung

GE 28320EE2 - Dect 6.0 InfoLink 2 Bedienungsanleitung

Avaya

Avaya 4600 Series Service-Handbuch

Mitel

Mitel MIVOICE OFFICE 400 6940 SIP Bedienungsanleitung