Panasonic ShowStopper PV-SS2710 Bedienungsanleitung

ORDER NO. MKE0101751C1

TV/Hard Disk Recorder Combination

PV-SS2710

SPECIFICATIONS

2001 Matsushita-Kotobuki Electronics Industries LTD. All rights

www.manualscenter.com

reserved. Unauthorized copying and distribution is a violation of law.

1. SAFETY PRECAUTIONS

1.1. GENERAL GUIDELINES

1. IMPORTANT SAFETY NOTICE

There are special components used in this equipment which are

important for safety. These parts are marked by in the Schematic

Diagrams, Circuit Board Layout, Exploded Views and Replacement

Parts List. It is essential that these critical parts should be replaced

with manufacturer’’s specified parts to prevent X-RADIATION, shock,

fire, or other hazards. Do not modify the original design without

permission of manufacturer.

2. An Isolation Transformer should always be used during the servicing

of HDR Combination whose chassis is not isolated from the AC power

line. Use a transformer of adequate power rating as this protects the

technician from accidents resulting in personal injury from electrical

shocks. It will also protect HDR Combination from being damaged by

accidental shorting that may occur during servicing.

3. When servicing, observe the original lead dress, especially the lead

dress in the high voltage circuits. If a short circuit is found, replace all

parts which have been overheated or damaged by the short circuit.

4. After servicing, see to it that all the protective devices such as

insulation barriers, insulation papers, shield, and isolation R-C

combinations are properly installed.

5. Before turning the receiver on, measure the resistance between B+

line and chassis ground. Connect (-) side of an ohmmeter to the B+

lines, and (+) side to chassis ground. Each line should have more

resistance than specified, as follows :

B+ Line

Minimum Resistance

130 V

1 k (Hot chassis ground)

27 V

180 (Cold chassis ground)

17 V

110 (Cold chassis ground)

6. When the TV set is not used for a long period of time, unplug the

power cord from the AC outlet.

7. Potentials, as high as 32.0 kV are present when this TV set is in

operation. Operation of the TV set without the rear cover involves the

danger of a shock hazard from the TV set power supply. Servicing

should not be attempted by anyone who is not thoroughly familiar with

the precautions necessary when working on high voltage equipment.

Always discharge the anode of the picture tube to the CRT ground of

receiver before handling the tube.

8. After servicing make the following leakage current checks to prevent

the customer from being exposed to shock hazards.

1.2. LEAKAGE CURRENT COLD CHECK

1. Unplug the AC cord and connect a jumper between the two prongs on

the plug.

2. For physically operated power switches, turn power on. Otherwise

skip step 2.

3. Measure the resistance value, with an ohmmeter, between the

jumpered AC plug and each exposed metallic cabinet part on the

receiver, such as screwheads, connectors, etc. When the exposed

metallic part has a return path to the chassis, the reading should be

between 1 M and 12 M . When the exposed metal does not have a

return path to the chassis, the reading must be infinity.

1.3. LEAKAGE CURRENT HOT CHECK

1. Plug the AC cord directly into the AC outlet.

Do not use a isolation transformer for this check.

www.manualscenter.com

2. Connect a 1.5 k , 10 W resistor, in parallel with a 0.15 F capacitor,

between each exposed metallic part on the set and a good earth

ground , as shown in Figure 1.

3. Use an AC voltmeter, with 1 k /V or more sensitivity, to measure the

potential across the resistor.

4. Check each exposed metallic part, and measure the voltage at each

point.

5. Reverse the AC plug in the AC outlet and repeat each of the above

measurements.

6. The potential at any point should not exceed 0.75 V RMS.

A leakage current tester (Simpson Model 229 equivalent) may be used

to make the hot checks. Leakage current must not exceed 1/2 mA. In

case a measurement is outside of the limits specified, there is a

possibility of shock hazard, and the receiver should be repaired and

rechecked before it is returned to the customer.

Figure 1

2. X-RADIATION

WARNING:

1. The potential source of X-Radiation in TV sets is the High Voltage

section and the picture tube.

2. When using a picture tube test fixture for service, ensure that the

fixture is capable of handling 32.0 kV without causing X-Radiation.

NOTE :

It is important to use an accurate periodically calibrated high voltage

meter.

1. Reduce the brightness to minimum.

2. Set the SERVICE switch to SERVICE .

3. Measure the High Voltage. The meter reading should indicate 30.0 kV±

2.0 kV.

If the meter indication is out of tolerance, immediate service and

correction is required to prevent the possibility of premature

component failure.

4. To prevent an X-Radiation possibly, it is essential to use the specified

picture tube.

HORIZONTAL OSCILLATOR DISABLE CIRCUIT TEST SERVICE WARNING:

The test must be made as a final check before set is returned to the customer.

1. With the rear cover removed, supply about a 120 V AC power source

to the set, turn on the set.

2. Set the customer controls to normal operating positions.

3. Short between TP891 and TP892 on the Main circuit board with a

jumper wire. Confirm that the picture goes out of horizontal sync.

4. If this does not occur, the horizontal oscillator disable circuit is not

operating. Follow the Repair Procedures of horizontal oscillator

disable circuit before the set is returned to customer.

REPAIR PROCEDURES OF HORIZONTAL OSCILLATOR DISABLE CIRCUIT

1. Connect a DC voltmeter between capacitor C513 (+) on the Main

circuit board and chassis ground.

2. If approximately +21.9 V is not present at that point when 120 V AC is

applied, find the cause. Check R503, R5342, C5325, C513 and D503.

3. Carefully check above specified parts and related circuits and parts.

When the circuit is repaired, try the horizontal oscillator disable circuit

test again.

CIRCUIT EXPLANATION

HORIZONTAL OSCILLATOR DISABLE CIRCUIT

The positive DC voltage, supplied from the D503 cathode for monitoring high voltage, is applied to the

IC5301 Pin11 through R503 and R5341. Under normal conditions, the voltage at IC5301 Pin 11 is less

than approx 3 V. If the high voltage at Flyback Tr Pin 5 exceeds the specified voltage, the positive DC

voltage which is supplied from the D503 cathode also increases. The increased voltage is applied to

IC5301 Pin11 through R503 and R5341. Due to the increased voltage at IC5301 Pin11, the horizontal

oscillator frequency increases, the picture goes out of horizontal sync, the beam current decreases

and the picture becomes dark in order to keep X-radiation under specification.

Figure 2

www.manualscenter.com

3. PREVENTION OF ELECTROSTATIC DISCHARGE

(ESD) TO ELECTROSTATICALLY SENSITIVE (ES)

DEVICES

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such

components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES

devices are integrated circuits and some field-effect transistors are semiconductor "chip"

components. The following techniques should be used to help reduce the incidence of component

damage caused by electrostatic discharge (ESD).

1. Immediately before handling any semiconductor component or

semiconductor-equipped assembly, drain off any ESD on your body

touching a known earth ground. Alternatively, obtain and wear a

commercially available discharging ESD wrist strap, which should be

removed for potential shock reasons prior to applying power to the

unit under test.

2. After removing an electrical assembly equipped with ES devices, place

the assembly on a conductive surface such as aluminum foil, to

prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES

devices.

4. Use only an antistatic solder removal device. Some solder removal

devices not classified as "antistatic (ESD protected)" can generate

electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical

charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package

until immediately before you are ready to install it. (Most replacement

ES devices are packaged with leads electrically shorted together by

conductive foam, aluminum foil or comparable conductive material).

7. Immediately before removing the protective material from the leads of

a replacement ES device, touch the protective material to the chassis

or circuit assembly into which the device will be installed.

CAUTION:

Be sure no power is applied to the chassis or circuit, and observe all

other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES

devices. (Otherwise harmless motion such as the brushing together of

your clothes fabric or the lifting of your foot from a carpeted floor can

generate static electricity (ESD) sufficient to damage an ES device).

"NOTE to CATV system installer :

This reminder is provided to call the CATV system installer’s attention

to Article 820-40 of the NEC that provides guidelines for proper

grounding and, in particular, specifies that the cable ground shall be

connected to the grounding system of the building, as close to the point

of cable entry as practical."

4. OPERATION GUIDE

5. SERVICE NOTES (PLEASE READ)

5.1. SERVICE NOTES

5.1.1. SERVICE POSITION

5.1.1.1. Service Position

CAUTION:

HOT CIRCUIT (Primary circuit) exists on the TV Main C.B.A. and the

Power Supply C.B.A. Use extreme care to prevent accidental shock

when servicing.

5.1.1.1.1. Service Position (1)

Fig. 1-1-1

Check the signal at the following wires and TPs. / Refer to “Check points and Waveforms for service

position (1).”

Fig. 1-1-2

Fig. 1-1-3

www.manualscenter.com

5.1.1.1.2. Service Position (2)

1. Remove the Rear Cover and the TV/Video/Power/HDR Unit. Then,

remove the C.B.A.s from the Bottom Frame.

2. Remove the PCB Holder Piece from the Bottom Frame as shown.

Fig. 1-2-1

3. Place the Main C.B.A. and TV Main C.B.A. on the Table. Then, connect

the Connector P7004 and P551.

4. In order to stabilize C.B.A.s, attach the PCB Holder Piece to both

C.B.A.s as shown.

Fig. 1-2-2

5. Place it along with Guide ribs on the Bottom Frame.

Service Position (2)

Fig. 1-2-3

Andere Panasonic Messgerät Handbücher

Panasonic

Panasonic TH13 Series Bedienungsanleitung

Panasonic

Panasonic WJ-NV300K/GJ Bedienungsanleitung

Panasonic

Panasonic LP-400 Series Gebrauchs- und Wartungshandbuch

Panasonic

Panasonic DMR-UBT1GL-K Bedienungsanleitung

Panasonic

Panasonic PV-V4524S Bedienungsanleitung

Panasonic

Panasonic WJHD500 - DIGITAL DISC RECORDE Bedienungsanleitung

Panasonic

Panasonic KW9M Eco-Power Meter Bedienungsanleitung

Panasonic

Panasonic RRQR100 - IC RECORDER Bedienungsanleitung

Panasonic

Panasonic KW4M Bedienungsanleitung

Panasonic

Panasonic KW2M-A Bedienungsanleitung

Panasonic

Panasonic LH2H preset Bedienungsanleitung

Panasonic

Panasonic K-NL316G Bedienungsanleitung

Panasonic

Panasonic DMR-HW220 Bedienungsanleitung

Panasonic

Panasonic KW9M Eco-Power Meter Bedienungsanleitung

Panasonic

Panasonic MKG1500-DE Bedienungsanleitung

Panasonic

Panasonic KW4S Bedienungsanleitung

Panasonic

Panasonic k-nl304k Bedienungsanleitung

Panasonic

Panasonic LH2H-FE-DHK Bedienungsanleitung

Panasonic

Panasonic AJ-PG50EJ Bedienungsanleitung

Panasonic

Panasonic Omnivision PV-V4600 Bedienungsanleitung

Panasonic

Panasonic AG6124 Bedienungsanleitung

Panasonic

Panasonic LP-V10U-C Bedienungsanleitung

Panasonic

Panasonic KW2G Eco-POWER METER Bedienungsanleitung

Panasonic

Panasonic AG-RT850P Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung