Panasonic AJ-DE97P Bedienungsanleitung

Non-Linear Editing System

Operating Instructions

AJ- P

This manual contains information on the hardware only.

For details on video and audio uploading, editing and other

operations, refer to the Reference Manual (AJ-SF97).

– 2 –

indicates safety information.

CAUTION:

Do not install or place this unit in a bookcase,

built-in cabinet or any other confined space in

order to maintain adequate ventilation. Ensure

that curtains and any other materials do not

obstruct the ventilation to prevent risk of

electric shock or fire hazard due to

overheating.

IMPORTANT

“Unauthorized recording of copyrighted television programs, video tapes and other materials may

infringe the right of copyright owners and be contrary to copyright laws.”

FCC Note:

This device complies with Part 15 of the FCC Rules. To

assure continued compliance follow the attached

installation instructions and do not make any

unauthorized modifications.

This equipment has been tested and found to comply

with the limits for a class A digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference when the equipment is operated in a

commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction

manual, may cause harmful interference to radio

communications. Operation of this equipment in a

residential area is likely to cause harmful interference in

which case the user will be required to correct the

interference at his own expense.

WARNING:

TO REDUCE THE RISK OF FIRE OR SHOCK

HAZARD, DO NOT EXPOSE THIS EQUIPMENT

TO RAIN OR MOISTURE.

CAUTION:

TO REDUCE THE RISK OF FIRE OR SHOCK

HAZARD AND ANNOYING INTERFERENCE,

USE THE RECOMMENDED ACCESSORIES

ONLY.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (service) instructions in the

literature accompanying the appliance.

CAUTION:

TO REDUCE THE RISK OF FIRE OR SHOCK

HAZARD, REFER CHANGE OF SWITCH

SETTING INSIDE THE UNIT TO QUALIFIED

SERVICE PERSONNEL.

CAUTION:

A CD-ROM DRIVE (CLASS 1 LASER PRODUCT)

IS INSTALLED IN THE PRODUCT.

USE OF CONTROLS OR ADJUSTMENTS OR

PERFORMANCE OF PROCEDURES OTHER

THAN THOSE SPECIFIED HEREIN MAY

RESULT IN HAZARDOUS RADIATION

EXPOSURE.

DO NOT MAKE ANY MODIFICATIONS. DO NOT

REPAIR BY YOURSELF. REFER SERVICING

TO QUALIFIED PERSONNEL.

CAUTION:

TO REDUCE THE RISK OF FIRE OR SHOCK

HAZARD, REFER INSTALLATION OF HARD-

DISK DRIVE TO QUALIFIED SERVICE

PERSONNEL.

HARD-DISK DRIVE MUST BE APPROVED BY

UL AND/OR CSA.

CAUTION:

TO REDUCE THE RISK OF FIRE OR SHOCK

HAZARD, REFER MOUNTING OF THE

OPTIONAL INTERFACE BOARD TO

QUALIFIED SERVICE PERSONNEL.

– 3 –

Contents

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Warning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Parts and Their Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

LED Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Basic Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Monitor Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

VTR Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Audio Equipment Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Editing Control Pad Connections . . . . . . . . . . . . . . . . . . . . . . . . . 16

System Startup and Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

System Startup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

System Exit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Connector Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Error Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

When the WARNING lamp is lighted . . . . . . . . . . . . . . . . . . . . . . 30

When the AUTO OFF lamp is lighted . . . . . . . . . . . . . . . . . . . . . . 30

Maintenance and Care. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Video Head Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Condensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

OWindows and Windows NT are registered trademarks of Microsoft Corporation.

OPentium is a registered trademark of Intel Corporation.

All other names of companies and products are the trademarks or registered trademarks of the companies

concerned.

– 4 –

Features

All-in-one tower design

This system contains a internal VTR for uploading and downloading data.

This feature translates into savings in terms of both the cost and space required for an externally connected

VTR, and it enables DVCPRO tapes to be loaded just like floppy disks or magneto-optical disks. The unit also

contains a hard disk for audio-video recording, and its size is the same as a tower-type personal computer. It

can be placed by the side of a desk for highly efficient editing operations.

Transfer and saving at twice/4 times normal speed

Data can be uploaded and downloaded between the internal VTR and hard drive at a speed of 2a(DVCPRO

50) or 4a(DVCPRO): this makes it possible to accomplish the preparatory work which has been viewed as a

kind of bottleneck in non-linear editing much more quickly.

Same high picture quality recording as with DVCPRO 50/DVCPRO

The same digital component compression recording system as for DVCPRO 50/DVCPRO is used to record data

onto the hard disk. The resulting picture quality is higher than that achieved by JPEG which has been adopted

by many non-linear editors (comparison made at the same transfer rate).

Furthermore, 140 minutes (with DVCPRO 50) or 280 minutes (with DVCPRO) of video and/or audio data can be

recorded on the internal hard drive (standard specification: 72GB).

Transfer of data while still compressed

Data still in a compressed format can be uploaded and downloaded between the internal VTR and hard drive.

Due to the absence of the A/D (D/A) conversion and compression/expansion processes, the picture quality of the

data is not subject to any deterioration whatsoever during the transfer process.

Editing of data while still compressed

In the case of cut editing, the unit leaves the recorded data completely unchanged. With the data still in its

compressed form, changes are made only to the read sequence and positions. During recording, the

compressed data does not need to be expanded at all, and it can be edited up to the form taken by the

completed package. This means that high picture quality is maintained even after editing.

(When the special effect and superimpose functions are used, the data is expanded into full bit digital video data,

and compressed back again after processing.)

Real-time preview of special effects

The unit contains a switcher so that wipe, dissolve and other special effects can be previewed on a real-time

basis during A/B roll editing. Trial-and-error operations can be repeated any number of times while checking

how the results turn out.

External VTR control (RS-422A)

The unit’s RS-422A (9 Pin) remote connector enables a wide range of analog or digital VTRs to be controlled.

This feature can also be used to introduce material or transmit perfect package programs using external VTRs.

All the proven features of the AJ-DE77’s operation system adopted

The user interfaces of the AJ-DE77 have served as a solid foundation on which to introduce improvements into

the system’s operating ease.

Streamlined operations using mouse

All the operator has to do in order to add, replace or delete cuts is rearrange the clips by operating the mouse.

Cut editing can be achieved with excellent response.

Warning

1. This unit must not be used on board a vehicle.

Doing so may damage the hard disk drive and destroy the data.

2. The user must not install any software programs which have not been designated for

use with this system.

The system may not operate properly if such programs are installed. For further details, consult your dealer.

– 5 –

System Configuration

Main unit

Keyboard

Mouse Power cord

Operating instructions

(which you are now reading)

Warranty card

Stabilizers (a4)

mounting screws (a8)

Installation manual

CAUTION:

To reduce the risk of injury due to tipping over,

mount the stabilizers before installation.

Service support guide

Do not subject the supplied mouse, keyboard or cables to strong bumps or

shocks. Doing so could damage them.

Ferrite cores (a4)

When the SCSI hard disk drive for external expansion

purposes is to be connected, attach one ferrite core to

one end of the SCSI I/F cable and the other one to the

other end.

– 6 –

Parts and Their Functions

Front Panel

1Main unit power switch

Set this switch to the OFF position after quitting the

system. If the power is turned off while the hard

disk drive is operating, data may be lost or the drive

may be damaged.

Do NOT turn off the power while white characters

on a blue background appear on the monitor

display (for the personal computer) during startup.

2Main unit power LED

3HDD sub switch

Press this switch if PC unit’s power does not come

on even when the main unit power switch is set to

ON.

Do not press this switch without good reason since

the power of the PC unit will be turned off if it

pressed while the power is supplied.

4HDD reset switch

Press this switch when the PC unit is not operating

properly. The start screen will now be restored,

and checks on the operation can be carried out.

Do NOT press this switch while white characters on

a blue background appear on the monitor display

(for the personal computer) during startup.

5Phones jack

The sound can be monitored when stereo

headphones are connected to this jack.

6Phones volume control

This is used to adjust the headphones volume and

the monitor output volume.

7Mic jack

The microphone is connected here for voice-over

editing operations.

8Mic volume control

This is used to adjust the level at which the

microphone sound is input.

9Cassette slot

M cassettes or L cassettes are loaded through this

slot. Consumer-use cassettes cannot be used for

recording or playback.

:Cassette tape EJECT button.

When this button is pressed, the tape is unloaded,

and the cassette is automatically ejected several

seconds later.

;CD-ROM drive

<Tray OPEN/CLOSE button

=Floppy disk drive

>Carrying handle

?HDD access display lamp (system)

@HDD access display lamp (AV data)

AScrews for securing mechanism

Loosen these screws when cleaning the head

mechanism transport system of the VTR unit or

when conducting other kinds of servicing or

maintenance. It will then be possible to pull out the

VTR unit’s mechanism.

After the maintenance work has been completed or

when the unit is to be moved, the mechanism must

be put back inside the unit and the screws

tightened up securely.

;

– 7 –

Parts and Their Functions

LED Display Panel

1AUTO OFF lamp

This lights when trouble has occurred in the unit’s

operation.

2Warning lamp

This lights when a warning item has occurred.

3Channel condition lamps

One of these lamps lights in accordance with the

error rate status.

(Green 5yellow 5amber)

Green: This lights when the video and audio play

signal error rates are at acceptable levels.

Yellow: This lights when either the video or audio

play signal error rate has deteriorated.

The playback picture remains normal even

while this lamp is lighted.

Amber: This lights when either the video or audio

play signal error rate is subject to

correction or interpolation.

4VTR lamp

This lights while the tape is traveling.

5Cassette loaded lamp

This lights when a cassette has been loaded in the

unit.

LED display panel

VTR

AUTO OFF

CH CONDITION

(Yellow)

(Amber)

(Green)

21345

–8 –

Parts and Their Functions

Rear Panel

1AC power socket [~AC IN]

The power cord (provided) is connected to this

socket.

2Fuse holder [FUSE 1/2, 125 V, 5 A]

This holder contains a 5 A fuse.

FUSE 1: for VTR unit

FUSE 2: for PC unit

3Ventilating fan

This fan prevents the internal temperature from

rising. Do not block the fan openings by placing the

unit right up against a wall or other object.

4Analog component video signal input

connectors [ANALOG, VIDEO INPUT, Y/PB/PR]

The analog component video signals are supplied

to these connectors. Connect a VTR or other video

unit with a component signal output capability here.

Analog composite video signal input connectors

[ANALOG, VIDEO INPUT, VIDEO IN]

The analog composite video signals are supplied to

these connectors which are joined by a loop-

through configuration. Connect a VTR or other

video unit with a composite signal output capability

here.

Analog reference video signal input connectors

[ANALOG, VIDEO INPUT, REF VIDEO IN]

The analog reference video signals are supplied to

these connectors which are joined by a loop-

through configuration.

In order to ensure that the video and audio signals

played back are stable, supply stable black burst

signals to these connectors from an external sync

signal generator.

775-ohm termination switch

Set this to ON for termination.

8Serial digital video signal input connectors

[SDI/SDTI IN] (option)

(For details on supporting this option, consult your

dealer.)

9Serial digital video signal output connectors

[SDI/SDTI OUT] (option)

(For details on supporting this option, consult your

dealer.)

AC IN

FUSE F1

125V

FUSE F2

125V

SIGNAL GND

IN OUT

SDI/SDIT

ACTIVE THROUGH

SDI/SDIT

(OPTION)

SDI

ANALOG

VIDEO INPUT VIDEO OUTPUT

AUDIO

OUT

AUDIO

MON

TC IN

OUT

DIGITAL AUDIO

MON

OUT

VIDEO

REF VODEO

OFF

75≠

OFF

75≠

CH1 CH2 CH3

PUSH

CH4

CH1 CH2

RS-232C

SERIAL 1

SERIAL 2

RS-422A

CH1-2 CH3-4

CH3 CH4

PUSH PUSH PUSH PUSH

CH1-2 CH3-4

PUSH PUSH

–9 –

Parts and Their Functions

Rear Panel

Analog component video signal output

connectors [ANALOG, VIDEO OUTPUT, Y/PB/PR]

The analog component video signals are output

from these connectors. Connect a VTR or other

video unit with a component signal input capability

here.

;Analog composite video signal output

connectors [ANALOG, VIDEO OUTPUT, 1/2]

The analog composite video signals are output from

these connectors.

Connect a VTR or other video unit with a composite

signal input capability here.

<Analog video monitor signal output connector

[ANALOG, VIDEO OUTPUT, MON OUT]

The analog composite video signals with

superimposed data are output from this connector.

Connect an monitor (Video) for monitoring the

pictures here.

=Analog audio signal input connectors

[ANALOG, AUDIO INPUT, CH1/CH2/CH3/CH4]

The analog audio signals are supplied to these

connectors. Connect a CD player, VTR or other

audio unit capable of outputting analog audio

signals to these connectors.

>Analog audio signal output connectors

[ANALOG, AUDIO OUTPUT, CH1/CH2/CH3/CH4]

The analog audio signals are output from these

connectors. Connect an audio amplifier, VTR other

audio unit capable of handling analog audio signals

to these connectors.

?Analog audio monitor signal output connectors

[ANALOG, AUDIO MON, L/R]

The audio playback signals are output from these

connectors. Connect monitor speakers, etc. to

them.

@Time code signal input connector [TC IN]

This connector is used when the time code signals

from an external source are to be supplied.

AC IN

FUSE F1

125V

FUSE F2

125V

SIGNAL GND

IN OUT

SDI/SDIT

ACTIVE THROUGH

SDI/SDIT

(OPTION)

SDI

ANALOG

VIDEO INPUT VIDEO OUTPUT

AUDIO

OUT

AUDIO

MON

TC IN

OUT

DIGITAL AUDIO

MON

OUT

VIDEO

REF VODEO

OFF

75≠

OFF

75≠

CH1 CH2 CH3

PUSH

CH4

CH1 CH2

RS-232C

SERIAL 1

SERIAL 2

RS-422A

CH1-2 CH3-4

CH3 CH4

PUSH PUSH PUSH PUSH

CH1-2 CH3-4

PUSH PUSH

;

–10 –

Parts and Their Functions

Rear Panel

ADigital audio signal input connector

[DIGITAL AUDIO IN, CH1-2/CH3-4]

The digital audio signals in the AES/EBU format are

supplied to these connectors.

BDigital audio signal output connectors

[DIGITAL AUDIO OUT, CH1-2/CH3-4]

Connect a VTR equipped with AES/EBU input

connectors here.

CSerial 1 connector [SERIAL 1]

Spare connector

DMouse connector [MOUSE]

Connect the mouse (provided) here.

EKeyboard connector [KEYBOARD]

Connect the keyboard (provided) here.

FParallel connector [PARALLEL]

Connect a device with a parallel interface here.

GSerial 2 connector [SERIAL 2]

Spare connector

HRS-232C connector [RS-232C]

Connect the editing pad here.

(Options supported: For details, please consult with

your dealer.)

IRS-422A connector [RS-422A]

Connect an external VTR (External VTR1) which

can be controlled using an RS-422A interface to

control its recording and playback functions.

AC IN

FUSE F1

125V

FUSE F2

125V

SIGNAL GND

IN OUT

SDI/SDIT

ACTIVE THROUGH

SDI/SDIT

(OPTION)

SDI

ANALOG

VIDEO INPUT VIDEO OUTPUT

AUDIO

OUT

AUDIO

MON

TC IN

OUT

DIGITAL AUDIO

MON

OUT

VIDEO

REF VODEO

OFF

75≠

OFF

75≠

CH1 CH2 CH3

PUSH

CH4

CH1 CH2

RS-232C

SERIAL 1

SERIAL 2

RS-422A

CH1-2 CH3-4

CH3 CH4

PUSH PUSH PUSH PUSH

CH1-2 CH3-4

PUSH PUSH

Andere Handbücher für AJ-DE97P

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Aufnahmegeräte Handbücher

Panasonic

Panasonic DMR-BCT855 Bedienungsanleitung

Panasonic

Panasonic NV-HD610EG Bedienungsanleitung

Panasonic

Panasonic WJHD309 - DIGITAL DISK RECORDER Bedienungsanleitung

Panasonic

Panasonic AYNE2000 - NONLINEAR AV WORKSTA Bedienungsanleitung

Panasonic

Panasonic WJND200 - NETWORK DISK RECORDER Bedienungsanleitung

Panasonic

Panasonic WJHD100 - DIGITAL DISC RECORDE Bedienungsanleitung

Panasonic

Panasonic AK-MSU935AP Bedienungsanleitung

Panasonic

Panasonic ESD Suppressor EZAEG2A Bedienungsanleitung

Panasonic

Panasonic AG-YAGHG Bedienungsanleitung

Panasonic

Panasonic AJ-HPM110 Bedienungsanleitung

Panasonic

Panasonic AGHPG10 - MEMORY CARD PORTABLE RECORDER Bedienungsanleitung

Panasonic

Panasonic WJ-NV300K Bedienungsanleitung

Panasonic

Panasonic WJ-NX400K/G Betriebsanleitung

Panasonic

Panasonic AJ-HPD2500P Bedienungsanleitung

Panasonic

Panasonic AJ-PD500P Bedienungsanleitung

Panasonic

Panasonic AJSPD850P - P2 DECK Bedienungsanleitung

Panasonic

Panasonic AJ-HPM100E Bedienungsanleitung

Panasonic

Panasonic WJHD316A - DIGITAL DISK RECORDER Bedienungsanleitung

Panasonic

Panasonic CZ-CLNC1U Bedienungsanleitung

Panasonic

Panasonic AV-HLC100E Bedienungsanleitung

Panasonic

Panasonic NV-HD90B Bedienungsanleitung

Panasonic

Panasonic WZ-DE45NH Bedienungsanleitung

Panasonic

Panasonic SLPR300 - CD RECORDER Bedienungsanleitung

Panasonic

Panasonic NV-HD100 Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch