Panasonic SLPR300 - CD RECORDER Bedienungsanleitung

ORDERNo.AD0109130C1

Compact Disk Recorder

SL-PR300

Mechanism unit:FMU-ZC4-1M (CD Changer),EMU-R7-1M (CD-R)

Colour

(S)...................Silver Type

Area

PP...................U.S.A. and Canada.

SPECIFICATIONS

Specifications

CD Player Section

System Compact disc digital audiosystem

Pitchcontrol ±12%

Signal-tonoise ratio 97 dB (1kHz)

Dynamicrange 93 dB (1kHz)

Frequencyresponse 20 Hz - 20 kHz (±1 dB)

Wowand flutter Less thanmeasurablelimit

Total harmonicdistortion0.0063 %(1kHz)

CDR Section

System Compact disc digital audio

recording system

Sampling frequency 44.1kHz

Frequencyresponse 20 Hz - 20 kHz (±1 dB)

Inputs:Analog (LINE IN) 300 mV

(Full scale-12 dB)/ 50 k

Digital OPTICAL× 1

COAXIAL× 1

Sampling frequency: 32 kHz,

44.1kHz, 48 kHz

Signal-to-noise ratio 94 dB (during playback, 1kHz)

Dynamicrange 91 dB (during playback, 1kHz)

Wowand flutter Less thanmeasurablelimit

Total harmonicdistortion0.0063 %(during playback, 1kHz)

Timer Section

Timer system DAILY TIMER operation (ON/OFF

timer)

ONCE TIMER operation (ON/OFF

timer)

Clock display 12-hourdisplay

Common Specifications

Output terminals:

Analog LINE × 1set, 2V/ 5k (Full scale)

Headphones × 1.4mW/ 32

Digital OPTICAL× 1

COAXIAL× 1

Power requirements AC 120 V, 60 Hz

Power consumption 40 Wpower ON mode

5WSTANDBY mode

Dimensions(W× H × D) 436 mm × 128 mm × 337 mm

(17-3/16 in. × 5in. × 13-1/4in.)

Mass 6.3kg(13.9lbs)

Notes:

-Specificationsaresubject to changewithoutnotice.

-Mass and dimensionsareapproximate.

Unauthorized copying and distribution isaviolation of law.

1. Accessories

-Remote control batteries...............2pcs.

[R6/LR6(AA, UM-3) ]

Note:These are availableon sales route.

-Stereo phono cables...............2pc.

(RJL2P004B08A)

-Remote control transmitter...............1pc.

(RAK-PR300)

2. Safety Precaution

(This “SafetyPrecaution” is appliedonlyinU.S.A..)

1. Before servicing, unplug the power cord to prevent an electric

shock.

2. When replacing parts, use onlymanufacture’srecommended

components for safety.

3. Check the condition of the power cord. Replace ifwear or damage

isevident.

4. After servicing, be sure to restore the lead dress, insulation

barriers, insulation papers, shields etc..

5. Before returning the serviced equipment to the customer, be sure

to make the following insulation resistance test to prevent the

customer from being exposed to ashock hazard.

2.1. Insulation resistance test

1. Unplug the power cord and short the twoprongs of the plug with

ajumper wire.

2. Turn on the power switch.

3. Measure the resistance value with ohmmeter between the

jumpered AC plug and each exposed metal cabinet parts, such as

screw heads antenna, control shafts, handlebrackets, etc..

Equipment with antenna terminalsshouldread between 3M -

5.2M to all exposed parts. (Refer to Fig. 2-1.)Equipment without

antenna terminalsshouldread approximatelyinfinityto all

exposed parts. (Refer to Fig. 2-2.)

Note:

Some exposedparts maybe isolatedfromthe chassis bydesign. These will readinfinity.

4. Ifthe measurement isoutside the specified limits, there isa

possibilityof ashock hazard. The equipment shouldbe repaired

and rechecked before itisreturned to the customer.

Fig. 2-1

Fig. 2-2

3. Precaution of Laser Diode

Caution:

Thisunitutilizes aclass 1laser. Invisiblelaser radiation isemitted

from the optical pickup lens when the unitisturn on:

1. Donot look directlyinto the pickup lens.

2. Donot use optical instruments to look at pickup lens.

3. Donot adjust the preset variableresistor on the optical pickup.

4. Donot disassemblethe optical pickup unit.

5. Ifthe optical pickup isreplaced, use the manufacture’sspecified

replacement pickup only.

6. Use of control or adjustment or performance of procedures other

than those specified hereinmayresultinhazardous radiation

exposure.

4. CD and CDR Messages

4.1. SCMS (Serial CopyManagement System)

Due tocopyright and otherconsiderations, the following restriction is nowinplace forCD-R

and CD-RW discs ontowhichthe digital signals of CDs have beencopied.

The digital qualityof CDs and otherdigital media canbe recordedtoCD-R and CD-RW using the

CDR function of this unit. However, it is not possible tomake a second generation digital copy

froma first generation copy. This restriction, knownasSCMS (Serial CopyManagement

System), is intendedtoprevent unlimiteddigital copying inthe interests of artists and other

This unit is designedtocomplywithSCMS restrictions.

The copyright laws allowrecordings tobe made forthe personal enjoyment of the individual

userbut theydo not allowsuchrecordings tobe usedforanyotherpurpose without permission

fromthe rightful ownerof the copyrights.

Notes

-Ifdigital recording of afirst generation digital copyisattempted,

“SCMS PROTECT” isshowninthe information display, and the

recording operation iscanceled.

-Inthe case of synchronized recording operations, Listening Edit

recording and Program Editrecording, when the first-generation

copyisafinalized CD-Ror CD-RWdisc loaded inthe 3-CD

changer, the recording type isautomaticallychanged fromdigital

to analog, and the recording type indicators light accordingly. (If

high-speed dubbing isturned on, itwill be turned off when the

recording type ischanged.)

4.2. CompatibleDisc Formats

The following disc formats canbe usedforrecording inthe CDR.

Inaddition tothe marks shownon the right, the phrases shownbelowortheirequivalent should

alsobe present somewhere on the packaging oraccompanying documentation:

FOR CONSUMER

FOR CONSUMER USE

FOR MUSIC USE ONLY

Discs that cannot be usedforrecording are as follows:

-Discs bearing marks other than those shownabove

-Discs intended for professional use and/or marked

“FORPROFESSIONALUSE ONLY”

-Discs intended for recording computer data

Inaddition tothe twodisc formats shownabove, the following disc format canalsobe playedin

eitherthe 3-CD changerorCDR.

Notes

-The unitcan playback audiodata recorded on CD-G, CD-EXTRA

and CD-Text discs as well, however the text information of CD-

Text discs cannot be displayed.

-IfaCD-Ror CD-RWhas been recorded using apersonal computer,

playback isonlypossibleifthe disc isrecorded inthe CD-Digital

Audioformat.

-You can playCD-Rand CD-RWdiscs recorded inthe musicCD

format.

Some of them, however, maynot be played depending on the disc

characteristics or recording condition.

-Donot use aCD-Ror CD-RWdisc that has been recorded inany

format other than the musicCD format or aCD-RWdisc that has

been used inanyformat other than the musicCD format with this

unit. Using such adisc with thisunitmaycause loudsound to

damage the speakers or cause hearing disorder.

5. Location of Controls

6. Preventing static electricity

Electrostatic discharge (ESD), whichoccurs whenstatic electricitystoredinthe body, fabric,

etc. is discharged, candestroythe laserdiode inthe traverse unit (optical pickup). Take care to

prevent this whenperforming repairs.

6.1. Grounding to prevent damage bystaticelectricity

Static electricityinthe work area candestroythe optical pickup (laserdiode) indevices suchas

CD players.

Be careful touse propergrounding inthe area where repairs are being performed.

6.1.1. Ground the workbench

1. Ground the workbench bylaying conductive material (such as a

conductive sheet) or an iron plate over itbefore placing the

traverse unit(optical pickup) on it. (Refer to Fig. 6-1.)

6.1.2. Ground yourself

1. Use an anti-staticwrist strap to release anystaticelectricitybuilt

up inyour body. (Refer to Fig. 6-1.)

Fig. 6-1

6.1.3. Handling the optical pickup

1. Inorder to maintainqualityduring transport and before

installation, both sides of the laser diode on the replacement

optical pickup are shorted. After replacement, return the shorted

parts to theiroriginal condition.

(Refer to the text.)

2. Donot use atester to check the condition of the laser diode inthe

optical pickup. The tester’sinternal power source can easily

destroythe laser diode.

6.2. Handling the traverse unit(optical pickup)

1. Donot subject the traverse unit(optical pickup) to strong shocks,

as itisasensitive, complex unit.

2. Cut off the shorted part of the flexiblecableusing nippers, etc.

after replacing the optical pickup. For specificdetails, refer to the

replacement procedure inthe text. Remove the anti-staticpin

when replacing the traverse unit. Becarefulnot to take too long a

time when attaching itto the connector.

3. Handlethe flexiblecablecarefullyas itmaybreak when subjected

to strong force.

4. Itisnot possibleto adjust the semi-fixed resistor that adjusts the

laser power. Donot turn it

7. Precautions for Service

[Handling of Traverse Unit and LaserPickup]

1. Donot touch anyperipheral element of the pickup or the actuator.

2. The traverse unitand the pickup are precision devices and

therefore must not be subjected to strong shock.

3. Donot use atester to examine the laser diode. (The diode can

easilybe destroyed bythe internal power supplyof the tester.)

4. To replace the traverse unit, pull out the metal short pinfor

protection from charging.

5. When replacing the pickup, after mounting anew pickup, remove

the solder on the short land which isprovided at the center of the

flexiblewire to open the circuit.

6. Half-fixed resistors for laser power adjustment are adjusted in

pairs at shipment to match the characteristics of the optical block.

Donot change the setting of these half-fixed resistors for laser

power adjustment.

7. New pickup isshorted bysoldering the land which isprovided at

the part nof the flexibleboard on the underside of it.

After completing the rapair, remove the solder to open the circuit.

[Destruction of Traverse Unit and LaserPickup byStatic Electricity]

Laserdiodes are easilydestroyedbystatic electricitychargedon clothing orthe humanbody.

Before repairing peripheral elements of the traverse unit orpickup, be sure totake the following

electrostatic protection:

1. Wear an antistaticwrist wrap.

2. With aconductive sheet or asteel plate on the workbench on

which the traverse unitor the pickup isto be repaired, ground the

sheet or the plate.

3. After removing the flexiblewire from the connector (CN601), short-

circuitthe flexiblewire bythe metal clip.

4. Short-circuitthe laser diode bysoldering the land which is

provided at the center of the flexiblewire for the pickup.

After completing the repair, remove the solder to open the circuit.

Please referto"Fig.4" of "Disassemblymethod <Changermechanismunit>" fordetails.

Andere Handbücher für SLPR300 - CD RECORDER

Inhaltsverzeichnis

Andere Panasonic Aufnahmegeräte Handbücher

Panasonic

Panasonic AJSPD850P - P2 DECK Bedienungsanleitung

Panasonic

Panasonic AJ-HPM110 Bedienungsanleitung

Panasonic

Panasonic NV-HD610EG Bedienungsanleitung

Panasonic

Panasonic AG-HMX100 Bedienungsanleitung

Panasonic

Panasonic AG-YAGHG Bedienungsanleitung

Panasonic

Panasonic WJND200 - NETWORK DISK RECORDER Bedienungsanleitung

Panasonic

Panasonic SVSR100 - SD AUDIO RECORDER Bedienungsanleitung

Panasonic

Panasonic SV-3800 Bedienungsanleitung

Panasonic

Panasonic RR-XS410 Bedienungsanleitung

Panasonic

Panasonic WJHD316A - DIGITAL DISK RECORDER Bedienungsanleitung

Panasonic

Panasonic DVCPRO P2 Series Bedienungsanleitung

Panasonic

Panasonic AJ-DE77P Bedienungsanleitung

Panasonic

Panasonic NV-HD90B Bedienungsanleitung

Panasonic

Panasonic AG-YA500G Bedienungsanleitung

Panasonic

Panasonic AG-HPG20 Bedienungsanleitung

Panasonic

Panasonic AJD850A - DVC STUDIO VTR Bedienungsanleitung

Panasonic

Panasonic AJ-DE97P Bedienungsanleitung

Panasonic

Panasonic PN28080i-ID Bedienungsanleitung

Panasonic

Panasonic AJLT85P - DVC PRO Bedienungsanleitung

Panasonic

Panasonic WJHD309A - DIGITAL DISK RECORDER Einrichtungshandbuch

Panasonic

Panasonic WJHD200 - Digital Disk Recorder Bedienungsanleitung

Panasonic

Panasonic AJHD1400 - DVCPRO HD VTR Bedienungsanleitung

Panasonic

Panasonic SLPR300 - CD RECORDER Bedienungsanleitung

Panasonic

Panasonic WJHD200 - Digital Disk Recorder Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch