Panasonic MC-CG463-KA76 Bedienungsanleitung

rights reserved. Unauthorized copying and distribu-

tion is a violation of law.

Order No VCB0608018CE

Vacuum Cleaner

MC-CG463-KA76

MC-CG463-KA7A

Destination : Swither land

TABLE OF CONTENTS

PAGE PAGE

1 Specifications ----------------------------------------------------- 2

2 Location of Controls and Components ------------------- 3

3 Troubleshooting Guide ----------------------------------------- 5

4 Disassembly and Assembly Instructions ---------------- 6

4.1. Dust box cover assembly removal -------------------- 6

4.2. Separate the upper and lower body units ----------- 6

4.3. Printed circuit board AU removal ---------------------- 7

4.4. Motor removal ---------------------------------------------- 8

4.5. Cord reel partition unit replacement ------------------ 9

4.6. Rail base U replacement -------------------------------10

4.7. Spring-loaded cord reel pre-winding-----------------10

5 Wiring Connection Diagram ---------------------------------11

6 Exploded View and Replacement Parts List -----------12

6.1. EXPLODED VIEW (ATTACHMENTS)---------------12

6.2. PARTS LIST (ATTACHMENTS)-----------------------13

6.3. EXPLODED VIEW (BODY UNIT) --------------------14

6.4. PARTS LIST (BODY UNIT) ----------------------------15

6.5. PACKING INSTRUCTIONS --------------------------- 16

6.6. PACKING LIST ------------------------------------------- 17

1 Specifications

Model No. MC-CG463

Power source AC230V~50Hz

Input power (MAX) 1800W

Input power (IEC) 1500W

Power control O

Extension wand Metal telescopic

Floor nozzle 2-Step O

Turbin nozzle -

Parquet nozzle -

Dimensions (WxLxH)mm 280x425x260

Cord length 5.0m

Net weight 4.5kg

Cleaning tools Crevice nozzle / Dusting brush

2 Location of Controls and Components

3 Troubleshooting Guide

CONDITION CHECKPOINT METHOD OF INSPECTION CAUSE / REMEDY

Motor fails to rotate.

(no noise is heard at all)

Power cord Chech power cord continuity between

pliug pins cord reel patition unit.

If there is no continuity, replace the

cord reel patition unit.

Main fuse (250V, 12A) Check main fuse continuity. If there is no continuity, replace the rail

base unit.

Motor continuity Check motor continuity between car-

bon brush holder tabs.

If there is no continuity, replace the

motor.

ON/OFF Switch Check continuity across switch connec-

tions.

If there is no continuity, replace the

switch.

Power board (P.C.B. AU) If cther checkpoints do not have any problems, then replace the control circuit

board AU (P.C.B. AU).

Rotary potentiometer Check if the potentiometer is in open

circuit.

If it is in open circuit, replace power

control.

Motor runs but there is no suc-

tion.

Hose or Suction inlet, Exten-

sion wand and nozzle

Check if there is any blockage in the

indicated parts.

If there is any blockage, remove it.

Dust bog / Secondary filter Check if dust bag is full or Secondary

filter is choked up.

If dust bag is foll, replace with a new

one. If Secondary filter is choked up,

remove and clean it out or replace.

Noise or vibration Motor fan Chech dust accumulated in motor fan

(if could happen if the vacuum cleaner

has been used with a broken dust bag

or without central filter).

If there is dust accumulated in the

motor fan, repiace the motor and check

filter condition (never try to dismantle

the motor fan).

Motor boes not change power

(runs alweys at full speed).

Rotary potentiometer Check possible bad contact of power

control potentiometer.

If there is bad contact, replace the

power control.

Power board (P.C.B.AU) Check if power board circuit is short-

circuited.

If it is short-circuited, replace power

board ass’y.

Motor runs irregularly Rotary potentiometer Check possible bad contact of power

control potentiometer.

If there is bad contact, replace power

control.

4 Disassembly and Assembly Instructions

Important notice: Before replacing any components, make sure to turn OFF the vacuum cleaner.

Remove the power plug from the outlet.

4.1. Dust box cover assembly

removal

1. Open the dust box cover assembly at an angle of approx.

45°. Insert a flat-blade screwdriver between the upper

body and the dust box cover assembly and move it in the

direction of the arrow mark to remove the dust box cover

assembly from its right side.

4.2. Separate the upper and lower

body units

1. Remove the five screws fixing the upper body U and

lower body U.

2. Remove the screw fixing the upper body U from the rear

side.

3. Lift the upper body U to separate it from the lower body U.

4.3. Printed circuit board AU

removal

1. Remove the Control knob U, supporter plate U and switch

cover U.

2. Remove the switch lever.

3. Disengage the fast-on terminal of the lead wire (red) lead-

ing to the fuse and that of the lead wire (blue) leading to

the cord reel connected to the printed circuit board.

4. Remove the fast-on terminal of the lead wire (gray and

orange) connecting the switch to the printed circuit board.

5. Remove the printed circuit board AU (with control).

4.4. Motor removal

1. Remove the dust box lid assembly. (Refer to paragraph

4.1 on P.6)

2. Remove the upper body from the lower body. (Refer to

paragraph 4.2 on P.6)

3. Remove the printed circuit board AU. (Refer to paragraph

4.3 on P.7)

4. Remove the two screws fixing the printed circuit board

holder and pull it out from the lower body.

5. Lift the motor set section from the lower body U.

6. Remove all components fitted to the motor.

a. Remove the motor support rubber (front).

b. Remove the motor support rubber (rear).

c. Remove the motor support.

d. Remove the noise suppressor U.

e. Remove all lead wires.

4.5. Cord reel partition unit replace-

ment

1. Increase the gap width between the cord reel and the

lower body with a screwdriver. While removing the cord

reel shaft from the side of the lower body, lift the cord reel

partition unit.

* For easy removal, pull out the cord slightly, and

then lift the cord reel.

4.6. Rail base U replacement

1. Remove the screw fixing the rail base U onto the cord reel

partition U.

2. Remove the rail base U from the cord reel partition U.

4.7. Spring-loaded cord reel pre-

winding

1. The cord reel partition U has a spring that pre-winds the

cord reel.

If the cord is not wound, then press the brake arm, and

the cord pre-winding will be loosened.

If you wish to apply pre-winding again, then wind the cord

three turns in the direction of the arrow mark.

* If you wish to release the pre-winding, then make

sure to hold the cord plug.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Staubsauger Handbücher

Panasonic

Panasonic MC-CG661 Bedienungsanleitung

Panasonic

Panasonic MCV215 - COMMERCIAL VACUUM Bedienungsanleitung

Panasonic

Panasonic MC-CL481K Bedienungsanleitung

Panasonic

Panasonic MCCG901 - CANISTER VACUUM - MULTI LANGUAGE Bedienungsanleitung

Panasonic

Panasonic National MC-4500 Bedienungsanleitung

Panasonic

Panasonic MCV7571 - UPRIGHT VACUUM Bedienungsanleitung

Panasonic

Panasonic Quickdraw MC-V5725 Bedienungsanleitung

Panasonic

Panasonic MC-SB53KH046 Bedienungsanleitung

Panasonic

Panasonic EXTREME Series Bedienungsanleitung

Panasonic

Panasonic QuickDraw MC-V5355 Bedienungsanleitung

Panasonic

Panasonic MCUG581 - PLATINUM UPRIGHT VAC Bedienungsanleitung

Panasonic

Panasonic MCCG381 - CANISTER VACUUM - MULTI LANGUAGE Bedienungsanleitung

Panasonic

Panasonic MC-E761 Bedienungsanleitung

Panasonic

Panasonic MCV120 - COMMERCIAL VACUUM Bedienungsanleitung

Panasonic

Panasonic Quickdraw MC-V5247 Bedienungsanleitung

Panasonic

Panasonic MC-UG725 Bedienungsanleitung

Panasonic

Panasonic MC-E7113K Bedienungsanleitung

Panasonic

Panasonic MCV3110 - COMMERCIAL VACUUM Bedienungsanleitung

Panasonic

Panasonic Ultra-Pro MC-V300 Bedienungsanleitung

Panasonic

Panasonic MC-UG327 Bedienungsanleitung

Panasonic

Panasonic MC-UG775-00 Bedienungsanleitung

Panasonic

Panasonic MC-UL975 Bedienungsanleitung

Panasonic

Panasonic MC-UG415 Bedienungsanleitung

Panasonic

Panasonic QuickDraw MC-V7325 Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch

Craftsman

Craftsman CMCVS001D1 Bedienungsanleitung