Panasonic MC-CG691-RA76 Bedienungsanleitung

Unauthorized copying and distribution is a violation

of law.

Order Number VCB0902002CE

Vacuum Cleaner

Model No. MC-CG691-RA76

MC-CG691-RC79

MC-CG691-RC7A

MC-CG691K-RP47

Product Color :Burgundy Red

Destination :Europe

TABLE OF CONTENTS

PAGE PAGE

1 Specifications ----------------------------------------------------- 2

2 Location of Controls and Components ------------------- 3

3 Troubleshooting Guide ----------------------------------------- 4

4 Disassembly and Assembly Instructions ---------------- 5

4.1. Dust box lid U removal ----------------------------------- 5

4.2. Separate the upper and lower body units ----------- 5

4.3. Separate the cord reel U and the body

partition U---------------------------------------------------- 6

4.4. Printed Circuit Board (PCB) AU removal ------------ 7

4.5. Motor removal ---------------------------------------------- 8

5 Wiring Connection Diagram ---------------------------------- 9

6 Exploded View and Replacement Parts List -----------10

6.1. EXPLODED VIEW (ATTACHMENTS) --------------10

6.2. PARTS LIST (ATTACHMENTS) ----------------------10

6.3. EXPLODED VIEW (BODY UNIT) -------------------- 11

6.4. PARTS LIST (BODY UNIT) ----------------------------12

6.5. PACKING INSTRUCTIONS----------------------------13

6.6. PACKING LIST--------------------------------------------14

1 Specifications

Model No. MC-CG691 MC-CG691K

Power source AC230V~50Hz AC240V~50Hz

Input power (MAX) 1300W

Power control O

Extension wand Telescopic

Floor nozzle O

Dimensions (W x L x H) 300×440×235

Cord length 5.0m

Net weight 5.0kg

Attachments (cleaning tools) Crevice nozzle/Upholstery nozzle

2 Location of Controls and Components

3 Troubleshooting Guide

CONDITION CHECKPOINT METHOD OF INSPECTION CAUSE / REMEDY

Motor does not rotate. Power supply cord Check power supply cord continu-

ity. Check cord reel U electrical con-

tinuity.

If there is no continuity, replace

cord reel U.

Fuse (250V, 10A)

(above PCB)

Check for fuse meltdown.

Visual meltdown inspection:

• Investigate the cause of the

meltdown

1. Burnt-out motor, coil short

circuit

2. Lead wire short circuit (short)

3. Burnt printed circuit board

(PCB)

If there has been a meltdown,

remove the problem fuse and

replace the PCB AU.

Motor unit Check electrical continuity between

motor unit terminals.

If there is no electrical continuity,

replace the motor unit.

ON/OFF switch Turn the switch on and off to check

electrical continuity

If there is any abnormality, replace

the PCB AU.

Printed circuit board (PCB) AU Check that there are no internal

part abnormalities (burnt, melted,

split, etc.).

If there is any abnormality, replace

the PCB AU.

Triac

(inside the printed circuit board AU)

Perform the following examination

and check the triac.

If there is any abnormality, replace

the PCB AU.

Motor runs, but there is no suction. Paper dust bag, dust box, second-

ary filter

Check if the paper dust bag or the

dust box is full of waste.

Is there some blockage in the sec-

ondary filter?

If the paper dust bag is full, replace

it with a new one.

If the dust box or the secondary fil-

ter is full of waste or there is a

waste blockage, throw out the

waste and clean.

Hose, extension wand, floor nozzle Check if there are any blockages. If there is a blockage, remove it.

Excessive vibration, excessive

noise

Motor unit Check if dust has accumulated in

the motor unit.

(Dust and waste can enter the

motor unit if there is no secondary

filter.)

Check for dust and waste in the

motor unit, as well as the condition

of the filter, and replace if neces-

sary.

Motor power (suction power) does

not change.

Printed control board (PCB) AU Turn the power control knob and

check if the suction power can be

changed.

If there is any abnormality, replace

the PCB AU.

4 Disassembly and Assembly Instructions

Caution:

When disassembling, check the component fitting state and wirings. After repairing, always restore them to the original

state.

Carefully handle the removed components, packing, etc. If they are damaged, then replace them with new ones.

After repairing, check that the components, etc., in the vicinity of the repaired sections are not damaged, the removed

components are in place, and the wirings are restored to the original state. Carry out the test run. Also check that the fol-

lowing requirements are met.

Insulation resistance

Must be 5 MΩor more when a DC voltage of 500 V is applied across the power plug and the motor core for one second.

Dielectric strength

Must withstand an AC voltage of 1,250 V applied across the power plug and the motor core for one minute.

Do not alter the model, parts, or materials during repair.

If a wiring unit is supplied as a repair part, replace the whole unit with the new one instead of repairing or reconnecting the

broken portions only.

Insert/remove the fast-on terminals by pushing/pulling them straight out without jiggling them or applying unnecessary

force.

4.1. Dust box lid U removal

1. Open the dust box lid U, insert a screwdriver between the

upper body and the area where the dust box lid U is

attached and move it in the direction of the arrow to

remove the dust box lid U from the upper body.

4.2. Separate the upper and lower

body units

1. Remove the four screws from the top of the body.

2. Remove the two screws on the rear side of the lower

body.

3. Remove the wheel supporter right and wheel supporter

left.

4. Remove the upper body.

4.3. Separate the cord reel U and

the body partition U

1. Remove the cord reel partition from the lower body.

2. Remove the two lead wire terminals.

*Pull the terminals out while holding down the termi-

nal lock release.

3. Slowly remove the plug from the body cover partition

stopper and release the pre-winding spring.

4. After inserting a screwdriver into the slit in the shaft and

turning 90 degrees to the left, pull the cord reel U away

from the body partition U.

*When assembling, carry out pre-winding for the

spring.

(The number of times to pre-wind is noted on the

metal plate.)

4.4. Printed Circuit Board (PCB) AU

removal

1. Remove the control terminal U, the power control and the

switch from the motor support cover U.

2. Remove the four screws affixing the motor support cover

3. Remove the motor support cover U and remove the PCB

AU.

4. Disengage the fast-on terminals of the two lead wires

connecting the PCB AU.

*Note:

When disengaging the fast-on terminals, pull straight

out without lateral movement while holding down the

lock release.

4.5. Motor removal

1. Remove the motor support rubber (rear) from the motor

support front.

2. Remove the two screws from the motor support front.

3. Remove the motor support front from the motor unit.

4. Remove the motor support rubber (front) from the motor

unit.

5. Remove the noise suppressor U from the motor unit.

6. Remove the two lead wires from the motor unit.

Note:

Make sure that the thermal protector is on the under-

side when setting the assembled motor into the lower

body.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Staubsauger Handbücher

Panasonic

Panasonic MC-V5209 Bedienungsanleitung

Panasonic

Panasonic MC-E3002-WP47 Bedienungsanleitung

Panasonic

Panasonic MC-SB52K Bedienungsanleitung

Panasonic

Panasonic MC-E4061 Bedienungsanleitung

Panasonic

Panasonic MC-CG710 Bedienungsanleitung

Panasonic

Panasonic QuickDraw MC-V5355 Bedienungsanleitung

Panasonic

Panasonic MCV7398 - UPRIGHT VACUUM Bedienungsanleitung

Panasonic

Panasonic MCV9640 - CANISTER VACUUM CLEA Bedienungsanleitung

Panasonic

Panasonic MCE583 - UPRIGHT VAC.-PLAT Bedienungsanleitung

Panasonic

Panasonic MCU-L426 Bedienungsanleitung

Panasonic

Panasonic MCV7399 - UPRIGHT VACUUM Bedienungsanleitung

Panasonic

Panasonic MCV5110 - COMMERCIAL VACUUM Bedienungsanleitung

Panasonic

Panasonic MC-CL575 Bedienungsanleitung

Panasonic

Panasonic MC-CJ905-R747 Bedienungsanleitung

Panasonic

Panasonic MC-V9644 Bedienungsanleitung

Panasonic

Panasonic MC-UL672 Bedienungsanleitung

Panasonic

Panasonic MCV5740 - UPRIGHT VACUUM Bedienungsanleitung

Panasonic

Panasonic MC-E593 Bedienungsanleitung

Panasonic

Panasonic MC-CG521RV47-MY Bedienungsanleitung

Panasonic

Panasonic MC-UG729 Bedienungsanleitung

Panasonic

Panasonic MC-E8021 Bedienungsanleitung

Panasonic

Panasonic MC-CL789 Bedienungsanleitung

Panasonic

Panasonic MC-UG502 Bedienungsanleitung

Panasonic

Panasonic MCV9638 - CANISTER VAC.-PLAT Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch

Craftsman

Craftsman CMCVS001D1 Bedienungsanleitung