Panasonic MC-CL676-ZC79 Bedienungsanleitung

rights reserved. Unauthorized copying and distribu-

tion is a violation of law.

Order No.VCB0707022CE

Vacuum Cleaner

Model No. MC-CL676-ZC79

Product Coior :Sherbet Blue

Destination :Europe

TABLE OF CONTENTS

PAGE PAGE

1 Specifications ----------------------------------------------------- 2

2 Location of Controls and Components ------------------- 3

3 Troubleshooting Guide ----------------------------------------- 5

4 Disassembly and Assembly Instructions ---------------- 6

4.1. Separate the upper and lower bodies. --------------- 6

4.2. P.C.B. assy removal -------------------------------------- 7

4.3. Motor removal ---------------------------------------------- 9

4.4. Cord reel unit replacement-----------------------------10

4.5. Spring-loaded cord reel pre-winding-----------------10

4.6. Installation of some Pakkin----------------------------- 11

4.7. How to disassemble the turbine nozzle-------------11

5 Wiring Connection Diagram ---------------------------------13

6 Exploded View and Replacement Parts List -----------14

6.1. EXPLODED VIEW (ATTACHMENTS) --------------14

6.2. PARTS LIST (ATTACHMENTS) ----------------------15

6.3. EXPLODED VIEW (BODY UNIT) --------------------16

6.4. PARTS LIST (BODY UNIT) ----------------------------17

6.5. PACKING INSTRUCTIONS----------------------------18

6.6. PACKING LIST ------------------------------------------- 19

1 Specifications

Model No. MC-CL676-ZC79

Power source 230V~50Hz

Input power (MAX) 2300W

Input power (Nominal) 2000W

Power control O

Extension wand Telescopic

Floor nozzle -

Turbin nozzle O

Dimensions (WxLxH)mm 290x470x280

Net weight 6.4kg

Cleaning tools Crevice nozzle / Upholstery nozzle

2 Location of Controls and Components

3 Troubleshooting Guide

CONDITION CHECKPOINT METHOD OF INSPECTION CAUSE / REMEDY

Motor fails to rotate Power supply cord Check power supply cord continu-

ity.

If there is no continuity, replace the

cord reel patition unit.

Fuse of P.C.B. Ass’y

(250V, 13A)

Check fuse continuity. If there is no continuity, replace

P.C.B. Ass’y.

Motor continuity Check the conduction between the

terminals of the motor.

If there is no continuity, replace the

motor.

ON/OFF Switch Check continuity across switch

connections

If there is no continuity, replace

P.C.B. Ass’y.

Triac (Inside of P.C.B.) Check if there is any problem in the

triac.

(Please refer to how to check the

triac.)

If it has any problem, replace the

P.C.B. Ass’y.

P.C.B. Ass’y Check the internal parts for any-

thing unusual. (burn-out, melt-

down, etc.)

If anything unusual is found,

replace the P.C.B. Ass’y with new

one.

Motor runs but there is no suction Hose or Suction inlet Check if there is any blockage in

the hose or suction inlet.

If there is any blockage, remove it.

Dust box unit

Upper filter Unit

Secondary filter

Check whether or not the dust box

unit is full of dust or dust is clogged

in the upper filter unit or secondary

filter.

If the dust box unit is full of dust,

then throw away the dust.

If dust is clogged in the upper filter

unit or secondary filter, then throw

away the dust and clean or replace

the upper filter unit or secondary fil-

ter.

Noise or vibration Motor fan Check dust accumulated in motor

fan (it could happen if the vacuum

cleaner has been used without cen-

tral filter).

If there is accumulated dust in the

motor fan, replace the motor and

check filter condition. (never try to

dismantle the motor fan)

Motor does not change power

(runs always at full speed)

P.C.B. Ass’y Examine the triac in the P.C.B.

Ass'y and check whether or not T1

and T2 are short-circuited.

If they are short-circuited, then

replace the P.C.B. Ass'y.

Motor runs irregularly P.C.B. Ass’y Check possible bad contact of

P.C.B. Ass’y.

Replace P.C.B. Ass’y.

4 Disassembly and Assembly Instructions

Important notice: Before replacing any components, make sure to turn OFF the vacuum cleaner.

Remove the power plug from the outlet.

4.1. Separate the upper and lower

bodies.

1. Remove the dust box assy from the main body.

2. Remove the filter cover from the upper body and remove

the filter unit.

3. Remove the three screws fixing the upper and lower bod-

ies.

4. Insert a flat-blade screwdriver into the gap between the

upper body and the ornamental plate unit. Move the

screwdriver in the direction of the arrow to remove the

ornamental plate unit from the three hooks on the upper

body. Remove the ornamental plate unit.

* Unhook the three tabs.

5. Remove the ornamental plate unit from the lower body.

6. Remove the screw fixing the caster unit (on the right in

the figure below) from the bottom of the lower body to

remove the lower caster support plate, caster unit.

7. From the bottom of the lower body, remove the four

screws fixing the upper and lower bodies.

8. Lift the upper body to separate it from the lower body.

4.2. P.C.B. assy removal

1. Remove the control shaft and switch cover unit with

spring A fitted.

2. Wiring treatment

3. Remove the right body packing from the lower body.

4. Remove the P.C.B. assy from the P.C.B. holder.

* When removing the P.C.B. assy, unhook it from the

tab on the P.C.B. holder by spreading the holder

frame.

Note: When removing the P.C.B. assy, do not bend it

to prevent damage and the wires from breaking.

5. Disconnect the fast-on terminal of the lead wire connect-

ing the fan motor unit to the P.C.B. assy.

* When connecting or disconnecting the fast-on ter-

minal, hold the P.C.B. assy and connecting terminals.

6. Disconnect the fast-on terminal of the lead wire connect-

ing the P.C.B. assy to the body partition assy.

4.3. Motor removal

1. Remove the P.C.B. holder from the lower body.

2. Remove the motor set from the lower body.

3. Remove all components fitted to the fan motor unit.

a. Remove the motor support rubber (rear).

b. Remove the motor support.

c. Remove the noise absorber.

d. Remove the motor support rubber (front).

4.4. Cord reel unit replacement

1. Lift the body partition assy (fitted with the cord reel unit)

while removing the cord reel shaft from the side of the

lower body.

2. Remove the screw fixing the body partition assy and the

cord reel unit.

3. Remove the cord reel unit from the body partition assy.

4.5. Spring-loaded cord reel pre-

winding

1. The body partition assy has a spring that pre-winds the

cord reel.

If the cord is not wound, then press the brake lever unit,

and the cord pre-winding will be loosened.

Pre-wind the cord as indicated by the arrow mark.

Number of pre-windings: Four turns

* If you wish to release the pre-winding, then make

sure to hold the cord plug.

Inhaltsverzeichnis

Andere Panasonic Staubsauger Handbücher

Panasonic

Panasonic MC-V7345C Bedienungsanleitung

Panasonic

Panasonic MC-SBU1F Bedienungsanleitung

Panasonic

Panasonic MC-CG711A249-AE Bedienungsanleitung

Panasonic

Panasonic MCV9640 - CANISTER VACUUM CLEA Bedienungsanleitung

Panasonic

Panasonic MC-V5737 Bedienungsanleitung

Panasonic

Panasonic MC-CJ905-R747 Bedienungsanleitung

Panasonic

Panasonic MC-V414 Bedienungsanleitung

Panasonic

Panasonic MCV5237 - UPRIGHT VACUUM-QKDR Bedienungsanleitung

Panasonic

Panasonic MC-YL799 Bedienungsanleitung

Panasonic

Panasonic MC-UL423 Bedienungsanleitung

Panasonic

Panasonic MCV5740 - UPRIGHT VACUUM Bedienungsanleitung

Panasonic

Panasonic MC-CG663 Bedienungsanleitung

Panasonic

Panasonic MC-E851 Bedienungsanleitung

Panasonic

Panasonic MCCG973 - CANISTER VAC - MULTI LANGUAGE Bedienungsanleitung

Panasonic

Panasonic MCCG902 - CANISTER VACUUM - MULTI LANGUAGE Bedienungsanleitung

Panasonic

Panasonic MC-CL565 Bedienungsanleitung

Panasonic

Panasonic MC-E3011-AP47 Bedienungsanleitung

Panasonic

Panasonic MC-UL910 Bedienungsanleitung

Panasonic

Panasonic MCV7400D - UPRIGHT VACUUM Bedienungsanleitung

Panasonic

Panasonic MC-CG373 Bedienungsanleitung

Panasonic

Panasonic Ultra-Pro MC-V200 Bedienungsanleitung

Panasonic

Panasonic MC-UL425 Bedienungsanleitung

Panasonic

Panasonic MC-UL810 Bedienungsanleitung

Panasonic

Panasonic MCV325 - COMMERCIAL VACUUM Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch

Craftsman

Craftsman CMCVS001D1 Bedienungsanleitung