Panasonic MC-E4061-00 Bedienungsanleitung

COMPANY, DIVISION OF PANASONIC

CORPORATION NORTH AMERICA. All rights

reserved. Unauthorized copying and distribution is a

violation of law.

MC-E4061-00

Vacuum Cleaner

Specifications are subject to change without notice for further improvement.

Order Number MAC0612003CE

1.2. Wire Management Drawing

NOTE:

For general servicing, it is necessary to eliminate pinching of any wire during reassembly. After servicing any electrical

component or electrical enclosure, the unit should be reassembled and checked for dielectric breakdown or current leakage.

MC-E4061-00

2.5. Packing Materials

2.5.1. Exploded View

2.5.2. Parts List (Packing Material)

Ref. No Part No. Part Name & Description Quantity Remarks

1 AC61ZDDDZ0E0 Carton Box 1 Includes Items A thru E

MC-E4061-00

3.1. Nozzle cover

3.1.1. Removal

1. Release the nozzle cover by rotating the nozzle cover

retainers to the UNLOCK position.

2. Rotate upward on the nozzle cover to remove it from the

nozzle base.

3.1.2. Installation

1. To replace the nozzle cover, make sure the nozzle cover

retainers are in the UNLOCK position.

2. Hook the front of the nozzle cover onto the nozzle base and

rotate downward.

3. Once inplace, rotate the nozzle cover retainers to the LOCK

position.

3.2. Beater Bar Assembly

Replacement

3.2.1. Removal

1. Remove the nozzle as outlined in the Nozzle cover section.

2. Disconnect mains lead from electrical outlet. Press handle

release pedal and tilt the handle down so cleaner is lying

flat on the floor.

3. Position hands on beater bar. If the belt is still attached to

the beater bar, there will be tension on it.

4. Carefully lift the right end of the beater bar and then lift the

left end.

5. Remove the belt from the motor drive shaft.

3.2.2. Installation

1. Reinstall new belt if necessary.

2. To replace the beater bar assembly, place the belt around

the motor shaft.

3. Loop the other end of the belt over the belt pulley on the

beater bar.

4. Insert the beater bar by placing the rounded portion of the

end caps down into the slots in the nozzle base.

5. Press firmly, checking to see that each end is completely

inserted.

3 REPLACEMENT INSTRUCTIONS

MC-E4061-00

6. Check to see that the belt is centered on the belt pulley and

that the beater bar turns freely.

7. Replace nozzle cover.

3.3. Belt Replacement

3.3.1. Removal

1. Follow all of the removal instructions outlined in the Beater

Bar Assembly Replacement section.

3.3.2. Installation

1. Place the new belt around the motor shaft and follow the

installation instructions in the Beater Bar Assembly

Replacement section.

3.4. Handle Assembly Replacement

3.4.1. Removal

1. Remove the dust cover.

2. Press the handle release button and rotate to the down

position.

3. Disconnect the wire leads, wire connectors, and wire tie, if

present.

4. Remove cord stopper.

5. Remove the handle retention clip.

6. Remove handle from body by twisting and pulling away

from unit.

3.4.2. Installation

1. Insert handle into body in the down position, make sure

handle release button is in proper position.

2. Reinstall handle retention clip.

3. Replace cord stopper.

NOTE: Never reuse a cord stopper. Always install a new

cord stopper whenever the old one is removed.

4. Reconnect wire leads, wire connectors and wire tie if

needed.

5. Reinstall dust cover. Care should be taken not to pinch any

wires.

NOTE: For general servicing, it is necessary to eliminate

pinching of any wire during reassembly. After servicing

any electrical component or electrical enclosure, the unit

should be reassembled and checked for dielectric

breakdown or current leakage.

3.5. Handle Release Assembly

Replacement

3.5.1. Removal

1. Remove handle from unit as described above.

2. Separate the handle assembly by removing (14) fourteen

screws as illustrated in the Exploded View (Handle

Assembly)

3. Remove handle release button and spring.

3.5.2. Installation

1. Insert new button and spring if necessary. Make sure button

is seated properly in grooves on Handle A.

2. Assemble handle by reversing order above.

3.6. Mains Lead Assembly

Replacement

3.6.1. Removal

1. Refer to Handle Assembly Replacement Section.

2. With handle removed from body disassemble handle by

removing fourteen (14) screws. Refer to Handle Assembly

Exploded View.

3. Remove handle release button and spring.

4. Remove damaged lead.

MC-E4061-00

3.6.2. Installation

1. Replace damaged lead. carefully routing mains lead as

illustrated.

2. Reinstall handle as outlined in the handle installation

section.

3. Replace the cord stopper, the two (2) cord stopper screws

and the wire connectors.

NOTE: Never reuse a cord stopper. Always install a new

cord stopper whenever the old one is removed.

NOTE: For general servicing, it is necessary to eliminate

pinching of any wire during reassembly. After servicing

any electrical component or electrical enclosure, the unit

should be reassembled and checked for dielectric

breakdown or current leakage.

3.7. ON/OFF Switch Replacement

3.7.1. Removal

1. Remove the dust cover to expose the electrical connections

of the ON/OFF switch.

2. Remove wires from switch.

3. Remove the ON/OFF switch, (for ON/OFF switch

replacement) by depressing the switch retaining tabs while

pushing up out of the dust compartment at the same time.

3.7.2. Installation

1. Re-connect lead wires to ON/OFF switch.

3.8. Motor Protector Replacement

3.8.1. Removal

1. Remove the dust cover.

2. Remove the motor protector cover, by releasing one of the

tabs that secure it to the dust compartment. Take care not

to break the tabs during removal.

3.8.2. Installation

1. Reinstall the motor protector and protector spring into the

dust compartment. Replace the motor protector cover by

applying pressure until both tabs snap into place.

NOTE: For general servicing, it is necessary to eliminate

pinching of any wire during reassembly. After servicing

any electrical component or electrical enclosure, the unit

should be reassembled and checked for dielectric

breakdown or current leakage.

MC-E4061-00

3.9. Motor Assembly Replacement

3.9.1. Removal

1. Remove the dust cover by removing the eight (8) screws.

2. Remove the lower plate, beater bar assembly, belt, the

plastic shaft and the nozzle housing as instructed in the

respective removal sections.

3. Disconnect the motor leads and remove the motor. Remove

the motor support rubber (rear), motor cap, noise

suppressor and the motor support rubber (front).

3.9.2. Installation

1. Place the motor back into the dust compartment with the

tabs on the motor support (rear) aligned parallel to the front

edge of the dust compartment.

2. Rewire per the Pictorial Wiring Diagram and Wiring

Management Drawing.

3. Replace the dust cover and the eight (8) screws.

4. Replace the nozzle housing assembly, belt, beater bar

assembly, and lower plate according to the respective

installation instructions.

MC-E4061-00

Inhaltsverzeichnis

Andere Panasonic Staubsauger Handbücher

Panasonic

Panasonic MC-UL425 Bedienungsanleitung

Panasonic

Panasonic MCV7370 - UPRIGHT VACUUM Bedienungsanleitung

Panasonic

Panasonic QuickDraw MC-V7325 Bedienungsanleitung

Panasonic

Panasonic MC-3920 TAIWAN Bedienungsanleitung

Panasonic

Panasonic MCV9620 - CANISTER VACUUM Bedienungsanleitung

Panasonic

Panasonic MC-V7600 Bedienungsanleitung

Panasonic

Panasonic MC-E881 Bedienungsanleitung

Panasonic

Panasonic Ultra-Pro MC-V400 Bedienungsanleitung

Panasonic

Panasonic MC-YL699 Bedienungsanleitung

Panasonic

Panasonic MC-UL423 Bedienungsanleitung

Panasonic

Panasonic MC-V6255 Bedienungsanleitung

Panasonic

Panasonic MCUG383 - UPRIGHT VACUUM - MULTI LANGUAGE Bedienungsanleitung

Panasonic

Panasonic MCV5117 - UPRIGHT VACUUM-QKDR Bedienungsanleitung

Panasonic

Panasonic MCUG471 - UPRIGHT VAC - MULTI LANGUAGE Bedienungsanleitung

Panasonic

Panasonic MCV120 - COMMERCIAL VACUUM Bedienungsanleitung

Panasonic

Panasonic MC-CG677K-S647 Bedienungsanleitung

Panasonic

Panasonic MC-CL305 Bedienungsanleitung

Panasonic

Panasonic MC-V5004 Bedienungsanleitung

Panasonic

Panasonic MCV7390 - UPRIGHT VACUUM Bedienungsanleitung

Panasonic

Panasonic MC-V414 Bedienungsanleitung

Panasonic

Panasonic MC-5010 Bedienungsanleitung

Panasonic

Panasonic mc-ul592 Bedienungsanleitung

Panasonic

Panasonic MC-BL480 Bedienungsanleitung

Panasonic

Panasonic MCV9640 - CANISTER VACUUM CLEA Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch