Panasonic Mc-ul592 Bedienungsanleitung

Order Number: PMMA091040CE

MC-UL592/MC-UL594

Vacuum Cleaner

SPECIFICATION

(6100-K). Unauthorized copying and distribution is a

violation of law.

MODEL MC-UL592 MC-UL594

POWER SOURCE

MAX INPUT 1400 W 1500 W

NOMINAL INPUT

DIMENSIONS (W x L x H)

NETT WEIGHT (kg) 8.6 kg 8.8 kg

EXTENSION WANDS

FLOOR NOZZEL - BOTTOM PLASTIC

ATTACHMENTS Hose, Extension Wand, Floor Nozzle

(

UL594

)

, Curved Wand, Crevice, Dustin

Brush

230V - 240V ~ 50 Hz

375mmX360mmX1120mm

PLASTIC

1200 - 1300 W

HOW TO ASSEMBLE YOUR CLEANER

A) HANDLE ASSEMBLY / HOSE ASSEMBLY / MAINS LEAD STORAGE

Set the hose around the hose

hook and insert the curved wand

to the curved wand holder.

4. Turn the upper cord storage

hook in the upright position and

wind the mains lead around the

upper and lower cord storage

hooks.

5. Insert the tools to its location as shown.

Remove tape and

screw from the

body.

1. Insert the base of

the handle into the

top of the vacuum

cleaner body as

shown. Push in

handle and tighten

the screw.

2. Insert the connection

pipe to suction inlet.

Ensure that the 2 hooks

of the connection pipe

are completely fitted into

the suction inlet.

Connection

Pipe

Hook

Tape

Suction Inlet

Dusting

Brush

Crevice

Mini Turbine

Nozzle

Extension

Wand

IMPORTANT:

Do not overtighten the screw.

Hose Hook

Curved Wand

Holder

Upper Cord

Storage Hook

Lower Cord

Storage Hook /

Carrying

Handle

Extension

Wand Holder

Curved Wand

Holder

MAINTAINING THE HEPA FILTER UNIT

TO CLEAN THE PRE-FILTER

Check HEPA filter unit frequently and clean when dirty.

Remove HEPA filter unit from dust bin by pulling both buckle as shown.

Clean HEPA filter unit by gently tapping over a rubbish container.

Tap on several sides to ensure best cleaning.

DO NOT clean the HEPA filter unit by brush or clean it with water.

Reinstall the HEPA filter unit as per reverse procedure.

Remove HEPA filter unit from dust bin. Refer to maintaining the HEPA

filter unit (as above).

Press the latch to open the dust bin plate.

Grasp the pre-filter and turn it clockwise and pull the pre-filter out.

Clean by gently tapping over a rubbish container.

Install the pre-filter to the dust bin, aligning the pre-filter tabs to the dust

bin slots. Each Pre Filter Tabs is different shape and adjust it to match

Dust Bin Slot, then turn counter-clockwise to the lock position until you hear

a “click” sound.

After the dust bin is empty of dust, firmly close the dust bin plate.

Make sure you hear a “click” sound to indicate that the dust bin plate is

fully latched.

Reassemble the HEPA filter unit. Place dust bin unit back into vacuum

cleaner by inserting the bottom first and tilting back.

Refer to dust bin cleaning.

Pull to release Pull to release

Buckle

Lid

Dust Bin

HEPA Filter

Unit

Pre-Filter

Dust Bin Slot

Pre-Filter Tab

REPLACING HEPA EXHAUST FILTER

The HEPA exhaust filter removes dirt from exhaust air.

Check HEPA exhaust filter after emptying dust bin.

Replace when dirty.

Lay down the vacuum cleaner as shown.

To remove filter cover, slide upwards the buckle as shown.

By holding the filter cover as shown, pull it out towards you.

Grasp the HEPA exhaust filter and pull out to remove it.

To install back the HEPA exhaust filter, put it into its original position.

Place the filter cover to the body as shown and press into its original location.

Slide down the buckle as shown.

WARNING

Do not operate vacuum cleaner with a clogged exhaust filter or

without the exhaust filter cover properly installed.

Important:

If HEPA Exhaust Filter become too dirty, it causes that air suction fall down.

HEPA Exhaust Filter cannot be cleaned and should be replaced at least

once a year.

Filter Cover

HEPA

Exhaust Filter

HEPA

Exhaust Filter

Buckle

THERMAL PROTECTOR

REMOVING AND INSTALLING LOWER PLATE

REPLACING BELT

This vacuum cleaner has a thermal protector which automatically trips to protect the vacuum cleaner from overheating.

If a clog prevents the normal flow of air to the motor, the thermal protector trips and turns the motor off automatically.

This allows the motor to cool in order to prevent possible damage to the vacuum cleaner.

TO CORRECT PROBLEMS:

Turn the vacuum cleaner off and unplug the power cord from the outlet to allow the vacuum cleaner to cool and the thermal

protector to reset automatically.

Check for and remove clogs, if necessary. Also check and replace any clogged filters and empty dust bin if necessary.

Wait approximately sixty (60) minutes and plug the vacuum cleaner in and turn back on to see if the motor protector has reset.

WARNING Electical SHock or Personal Injury Hazard

Disconnect the electrical supply before servicing or cleaning the vacuum cleaner.

Failure to do so could result in electrical shock or personal injury from vacuum cleaner suddenly starting.

Before servicing any parts, unplug the mains lead from electrical outlet.

Always place paper under nozzle whenever lower plate is removed to

protect floor.

Place body in upright position and turn vacuum cleaner over to expose

lower plate.

Release lower plate by rotating the lower plate latches to the UNLOCK

position.

Remove lower plate and remove any residue that may exist in belt area.

Reinstall lower plate by hooking front end of lower plate into slots on front

of nozzle.

Press lower plate onto nozzle and secure by rotating the lower plate

latches to the LOCK position.

Replace belt whenever a burning rubber smell caused by excessive

slippage occurs.

Remove lower plate. See “Removing and Installing Lower Plate”.

Remove beater bar by carefully lifting out.

Remove worn or broken belt.

Clean beater bar and the end caps.

Motor Shaft

Motor Shaft Belt

Beater Bar

Belt Groove

End Cap

Latches

Latches Lower Plate

CLEANING BEATER BAR

CLEANING EXTERIOR AND TOOLS

Loop new belt around motor shaft and beater bar belt groove.

Reinstall beater bar by inserting the end cap of the beater bar to the slot

for both side.

After reinstalling the beater bar, turn it by hand to make sure that the belt is

not twisted of pinched and that all rotating parts turn freely.

Reinstall lower plate. See “Removing and Installing Lower Plate”.

Clean beater bar for Nozzle and Mini Turbine Nozzle after every five uses.

Turn vacuum cleaner over, exposing the beater bar for Nozzle.

Cut off any carpet pile and lint entangled around beater bar for Nozzle

and Mini Turbine Nozzle with a pair of scissors.

Clean exterior using a clean, soft cloth that has been dipped in a solution of mild liquird detergent and water and wrung dry.

DO NOT drip water on the vacuum cleaner and wipe dry after cleaning.

DO NOT clean tools in dishwasher or clothes washer.

DO NOT use tools if they are wet.

Wash tools in warm soapy water, rinse and air dry.

REPLACING MOTOR ASSY AND OVERLOAD PROTECTOR

- Following step replacing belt and Beater bar unit.

- Remove the 1 screw from the Pedal shaft to detach

the Pedal.

- Loosen 3 screw from the Lower plate.

- Pull out the pedal shaft slightly.

- Loosen 3 screw at the frame and remove together.

- Push the hook to unlock Floor nozzle upper.

- Trun back the set.

- Open the cover of Floor nozzle upper.

- Pull the Nozzle hose from the Extention wand holder.

- Take out the Floor nozzle upper and remove nicely.

- Can see the Overload protector and Motor cap.

- Loose 4 screw at Motor cap and remove.

- Motor Support plate and take out the Motor assy.

- After open or take out the wire connector please

make sure the colour of wire must correctly and

same to the original.

A) Brown wire

B) Black wire

OVERLOAD PROTECTOR

REPLACING FAN MOTOR UNIT, CAPACITOR AND FUSE ASSY

IMPORTANT : Before replacing any part always DISCONNECT FROM THE ELECTRICITY SUPPLY.

- Pull out the Handle from Body assy and move up the

Dust compartment assy.

- Turn back the set.

- Loosen 2 screw at the Rear body assy.

- Turn back to normal.

- Push up the Buckle to open the Filter cover.

- Take out the Filter cover.

- Loosen 10 screw at the Front body and take out.

- Make sure all the part place before dismantle or

change to new part.

- Location of Safety part.

- Pull out the connector Capacitor from Fan Motor unit.

- Pull out the connector wire from Fan motor unit.

- After that move up the Fan motor unit.

- Make sure the wire colour before pull out the

connector wire from the Switch.

(Red wire and Brown wire).

A) Brown wire

B) Red wire

- Position of Fuse assy.

Andere Handbücher für mc-ul592

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Staubsauger Handbücher

Panasonic

Panasonic MC-CG710 Bedienungsanleitung

Panasonic

Panasonic ?MC-CL743 Bedienungsanleitung

Panasonic

Panasonic MCV9638 - CANISTER VAC.-PLAT Bedienungsanleitung

Panasonic

Panasonic MC-V21003 Bedienungsanleitung

Panasonic

Panasonic MCV7368 - UPRIGHT VACUUM PLATI Bedienungsanleitung

Panasonic

Panasonic MC-CG955 Bedienungsanleitung

Panasonic

Panasonic MC-9040 Bedienungsanleitung

Panasonic

Panasonic MCV7407D - UPRIGHT VACUUM Bedienungsanleitung

Panasonic

Panasonic MCV5237 - UPRIGHT VACUUM-QKDR Bedienungsanleitung

Panasonic

Panasonic MC-UL555 Bedienungsanleitung

Panasonic

Panasonic MC-CL435 Bedienungsanleitung

Panasonic

Panasonic MC-YL635T146-BN Bedienungsanleitung

Panasonic

Panasonic MCV7721 - UPRIGHT VACUUM Bedienungsanleitung

Panasonic

Panasonic MCV225 - COMMERCIAL VACUUM Bedienungsanleitung

Panasonic

Panasonic MC-GG213 Bedienungsanleitung

Panasonic

Panasonic National MC-4500 Bedienungsanleitung

Panasonic

Panasonic MCV5110 - COMMERCIAL VACUUM Bedienungsanleitung

Panasonic

Panasonic MC-V5454 Bedienungsanleitung

Panasonic

Panasonic MCV7347 - UPRIGHT VACUUM-QKDR Bedienungsanleitung

Panasonic

Panasonic MC-UG614 Bedienungsanleitung

Panasonic

Panasonic Ultra-Pro MC-V150 Bedienungsanleitung

Panasonic

Panasonic MC-YL623G147-AE Bedienungsanleitung

Panasonic

Panasonic MC-UG504 Bedienungsanleitung

Panasonic

Panasonic MCV7309 - UPRIGHT VACUUM Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch

Panasonic mc-ul592 Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken