Panasonic MCV9620 - CANISTER VACUUM Bedienungsanleitung

Operating

Instructions

VACUUM CLEANER

MC-V9620

Panasonic.

Before operating this unit, please read these instructions completely.

TABLE OF CONTENTS

Safety Instructions 1

Parts Identification and Features Chart 2

Vacuum Cleaner Assembly 3-4

How Your Vacuum Works 4

Use -How To Start 5

Suggested Pile Height Settings 5

Handle Switch 5

Attachments and Use 6

Performance Features -Overload Protector, Suction Control,

Hose Swivel, and Performance Indicator 7

Vacuuming Tips 7

Bag Changing and Motor Safety Filter Cleaning 8

Cleaning Exterior and Attachments 9

POWER NOZZLE Care -Light Bulb Changing, Belt Changing and Agitator Cleaning 9-10

Brush Servicing and Agitator Exploded View 11

Troubleshooting 12

Warranty 17

Service Information Back Cover

CONSUMER INFORMATION

VCMA Vacuum Cleaner Manufacturer's Association

Service to the Industry since 1913 (Panasonic -An Association Member)

This information has been compiled by the Vacuum Cleaner Manufacturer's Association from

Government and Private Sources concerned with product safety. These basic guidelines are for

your protection and convenience.

Proper assembly and safe use of your vacuum cleaner are your responsibilities. Your

cleaner is intended only for household use. The cleaner should be stored in adry, indoor

area. Read the Operating Instructions carefully for important use and safety information.

JWARNING

TO AVOID ELECTRIC SHOCK

Never vacuum damp or wet surfaces or liquids.

Do not store machine outdoors.

Replace worn or frayed power cord immediately.

TO AVOID ACCIDENTS

Except for hand-held cleaners, keep machine on floor -not on chairs, tables, etc.

Store machine promptly after each use to prevent accidents from tripping over power cord or machine.

Use machine and accessories only in manner intended by manufacturers.

The use of an extension cord is not recommended.

IMPORTANT SAFETY INSTRUCTIONS

When using vacuum cleaner, basic precautions should always

be followed, including the following:

READ ALL INSTRUCTIONS BEFORE

USING THIS VACUUM CLEANER

WARNING

To reduce the risk of fire, electric shock, or injury:

1.Do not leave vacuum cleaner when plugged in. Unplug from outlet when not in

use and before servicing.

2. To reduce the risk of electric shock -DO NOT use outdoors or on wet surfaces.

3. Do not allow to be used as atoy. Close attention is necessary when used by

or near children.

4. Use only as described in this manual. Use only manufacturer's recom-

mended attachments.

5. Do not use with damaged cord or plug. If vacuum cleaner is not working as

it should, has been dropped, damaged, left outdoors, or dropped into water,

return it to an authorized Panasonic Service Center.

6. Do not pull or carry by cord, use cord as ahandle, close adoor on cord, or

pull cord around sharp edges or corners. Do not run vacuum cleaner over

cord. Keep cord away from heated surfaces.

7. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

8. Do not handle plug or vacuum cleaner with wet hands.

9. Do not put any object into openings. Do not use with any opening blocked;

keep free of dust, lint, hair and anything that may reduce air flow.

10. Keep hair, loose clothing, fingers, and all parts of body away from openings

and moving parts.

11. Do not pick up anything that is burning or smoking, such as cigarettes,

matches or hot ashes.

12. Do not use without dust bag and/or filters in place.

13. Turn off all controls before unplugging.

14. Use extra care when cleaning on stairs.

15. Do not use to pick up flammable or combustible liquids such as gasoline or

use in areas where they may be present.

16. Always turn cleaner off before connecting or disconnecting the hose or

Power Nozzle.

SAVE THESE INSTRUCTIONS

THIS VACUUM CLEANER IS INTENDED FOR HOUSEHOLD USE ONLY

Notice: Before you plug in your Panasonic Vacuum Cleaner, make sure that the voltage indicated on the

rating plate located on the bottom of the vacuum cleaner is the same as your local supply.

-1-

PARTS IDENTIFICATION

Mete/

Wands

ATTACHMENTS

CrwiceTool —i./

Dusting Brush —

Fabric Brush —

Floor Brush —

(

Cover Qn-Off

Cord Rewind

Button

Power

Cord

(Not

Shown)

y/Motor Safety Filter

(Behind Dust Bag)

POWER

NOZZLE

Model/Serial

Numbers

(On Bottom)

Dust Bag

Type C-5

Micron Bag

Holder

Pile Height Pile Height

Pedal Indicator

FEATURE CHART

(PANASONIC CANISTER TYPE VACUUM CLEANER)

FEATURES

Model

POWER OVERLOAD

PROTECTOR HEADLIGHT CORD

LENGTH

(feet)

TOOLS POWER

NOZZLE

MC-V9620 120V.AC(60Hz)

11.0 Amps Yes Yes 20 Yes Yes

-2-

VACUUMCLEANER ASSEMBLY

AWARNING Electrical Shock Hazard.

Do not plug into electrical supply until assembly is complete. Doing so

could result in electrical shock or injury.

•Do not get the power cord caught under the agitator when using the

cleaning tools. Keep cord out from under POWER NOZZLE when

vacuuming.

Before assembling your vacuum cleaner, be sure you have all parts shown on page 2.

WANDS

POWER NOZZLE

Slide wands

together until

wand button

snaps into

place.

POWER NOZZLE

1. Insert wands into POWER

NOZZLE until the wand button

snaps into the grooved slot. f?

Slot

Connect POWER NOZZLE plug and cord as

shown. Do not force. If hard to install, turn the

plug over and try again.

CANISTER

I.Open the canister

hood by gripping

the lid release. Pull

out and up to open

hood. See page 2

for location of lid

2. Check the dust

bag. See page 8for installation instructions.

3. Check motor safety filter.

See page 8for installation instructions.

-3

ASSEMBLY (continued)

HOOD-TOOL STORAGE

It is normal for the canister hood to come off

when opened further than needed. Line up the

hinges, insert them, and close the hood to

lit.

1. Insert hose into

canister until it snaps

in place.

TO REMOVE: Lift

hose latch tab upward

and pull up on hose.

HOSE

2. Insert handle into

wand until lock

button snaps in

place. Be sure

hose is not

twisted.

TO REMOVE: Press

handle release

button and pull up

on handle.

HOW YOUR VACUUM WORKS

The vacuum cleaner creates suction that picks up

dirt. Rapidly moving air carries the dirt to the dust

bag through the airflow passage. The dust bag

lets the air pass through, while it traps the dirt

For best cleaning results, keep the airflow

passage open. Check the starred

areas occasionally for clogs.

-4-

USE -HOW TO START

WARNING Personal Injury and Product Damage Hazard

•DO NOTplug in if switch is in ON position. Personal injury or damage could result.

•The cord moves rapidly when rewinding. Keep children away and provide aclear

path when rewinding the cord to prevent personal injury.

•DO NOT use outlets above counters. Damage to items in surrounding area could occur.

NOTE: To reduce the risk of electric shock, this vacuum cleaner has apolarized plug, (one blade is wider

than the other). This plug will fit in apolarized outlet only one way. If the plug does not fit fully in the

outlet, reverse the plug. If it still does not fit, contact aqualified electrician to install the proper outlet.

DO NOT CHANGE THE PLUG IN ANY WAY.

TO REWIND: Remove the cord from the cord grip.

Unplug the cleaner. Hold the plug while rewinding

to prevent damage or injury from the moving cord.

Push cord rewind button. The cord will not rewind

until the cord rewind button is pushed.

4. Lower wand

from upright

position by

pressing on the

handle release

pedal.

5. Select apile

height setting by

pressing the small

pedal on the rear.

The pile height

setting is shown in

the window.

1. Pull cord out of canister to desired length.

2. Snap

cord into

grip to

prevent

accidental

rewinding.

3. Plug cord into 120-volt outlet located near the

floor.

SUGGESTED PILE HEIGHT SETTINGS

For best deep down cleaning, use the XLO setting. However, you may need to raise the height to make

some jobs easier, {such as scatter rugs and some deep pile carpets) and to prevent the vacuum cleaner

from shutting off. Suggested settings are: XLO- most carpets and bare floors. LO-low to medium pile.

MED- medium to deep pile. Hl-shag; deep pile; scatter rugs.

1. Press "ON-

OFF" switch

to start

canister and

POWER

NOZZLE.

On-Off Switch

Cord

Rewind Button

HANDLE SWITCH 2. There are two

positions on the handle,

Bare Floor/Off and

Carpet. Bare Floor/Off

position turns the

power brush off on the

Power Nozzle to be

used on uncarpeted floors. The Canister motor

only will run. Carpet position turns on both the

Canister motor and the Power Nozzle motor for

normal carpet cleaning.

-5-

ATTACHMENTS AND USE

ACAUTION

DO NOT attach or remove handle or wands while cleaner is ON. This could cause

sparking and damage the electrical contacts.

ATTACHMENTS ON HANDLE

NOTE: If the POWER

NOZZLE is attached, turn

cleaner off before removing

handle from wands.

1. Press lock button, then

pull to remove handle from

wand.

2. Slide attachments

firmly on handle as

needed (See chart on

this page.)

ATTACHMENTS

ON WANDS

NOTE: If the POWER NOZZLE is attached, turn

cleaner off before removing plug from wands.

fft 1. To remove

.lwands from

POWER

NOZZLE, lock

wands in

straight-up

position.

ATTACHMENT USE

2. Remove POWER

NOZZLE plug and cord

from holders.

3. Steady POWER

NOZZLE with foot

and turn wands

counterclockwise

until lock button

disappears, then

pull wands out of

POWER NOZZLE.

4. Put attachments

on wands as

needed. {See chart

on this page.)

WARNING

Personal Injury Hazard

Use care if canister is placed on

stairs. If it falls, personal injury or

property damage could result.

ATTACHMENT CLEANING AREA

Furniture* Between

Cushions* Drapes" Stairs

Bare

Floors Carpeted

Floors Rugs Walls

DUSTING n

BRUSH ES. XXX

crevice C2rr~-~»

TOOL 7XX

FABRIC A}

BRUSH XX

FLOOR Q

BRUSH Cf^3 XXX

POWER -J>

NOZZLE ^XX

-6-

PERFORMANCE FEATURES

OVERLOAD PROTECTOR

POWER NOZZLE

The overload protector stops the motor when the

brush jams and prevents belt breakage.

TO CORRECT PROBLEM:

1. Unplug electrical cord.

2. Check brush and brush support areas for

excessive lint build-up or jamming.

3. Clean jammed area. (See pages 9-10).

TO RESET: Press reset button on top of the

POWER NOZZLE. Plug in and turn on cleaner.

SUCTION

CONTROL

The suction

control increases

or decreases the

suction for dif-

ferent fabric and

carpet weights.

Opening the

control decreases suction for draperies and

lightweight rugs. Closing the control increases

suction for furniture and carpets.

HOSE SWIVEL

The hose swivel allows

the hose to turn without

moving the canister.

This is helpful for

cleaning in small areas.

Check hose for twisting

before pulling canister.

PERFORMANCE INDICATOR

When the unit is running

the lines in the indicator

windows will be clear if

there are no clogs. When

the lines turn completely

red there is aneed to check the dust bag for

being full or the other areas that may be clogged.

See page 4.

NOTE: Red lines may appear when using

attachments or when cleaning new carpet, due to

reduced air flow by the attachments themselves

or new carpet fuzz filling the bag quickly.

VACUUMING TIPS

Suggested sweeping pattern.

For best cleaning action, the POWER NOZZLE should be pushed straight away from you and pulled

straight back. At the end of each pull stroke, the direction of the POWER NOZZLE should be changed to

point into the next section to be cleaned. This pattern should be continued across the rug with slow,

gliding motions.

NOTE: Fast,

jerky strokes

do not

provide

complete

cleaning.

Small areas can be

cleaned without moving

the canister. The hose

swivel allows the hose to

turn from side to side

while the canister stays

in place. Check hose for

twisting before pulling

canister. Carpeted stairs

need to be

vacuumed

regularly. For

best cleaning

results, fully

close the

suction control.

-7-

BAG CHANGING

For best cleaning results, the dust bag should

be changed often. Use Panasonic micron dust

bag type C-5

1. Unplug cord from

wall outlet.

2. Pull lid release

out and up, then lift

canister hood.

3. Remove cardboard

tab from red bag mount

by pressing away and

lifting up.

4. Pull bag out of the

red bag mount.

5. The red bag

mount will flip

forward after

removing bag. This

will prevent the lid

from closing until a

new bag is installed.

6. Raise red bag mount up.

7. Install bag into slots

pushing down until

the cardboard tab

locks into position and

the holes align.

8. Close and latch

canister hood.

9. Plug cord into wall outlet.

10. Bags are available at Panasonic Dealers and

Distributors.

ACAUTION

NEVER REUSE ADUSTBAG. Very fine materials, such as carpet fresheners, face

powder, fine dust, plaster, soot, new carpet lint, etc. can clog the bag and cause it

to burst before it is full. Change bag more often when vacuuming these materials.

MOTOR SAFETY FILTER CLEANING

Check motor safety filter occasionally and clean when dirty.

WARNING Electrical Shock Hazard

Do not operate the cleaner without the motor safety filter. Be sure the filter is dry

andproperly installed to prevent motor failure and/or electrical shock.

1. Unplug cord from

wall outlet and

remove bag.

2. Pull out safety

filter as shown.

3. Wash filter in

warm soapy water,

rinse, then air dry.

Do not clean in

dishwasher or

install while damp.

4. Snap filter back

into canister.

5. Install bag.

-8-

Andere Handbücher für MCV9620 - CANISTER VACUUM

Andere Panasonic Staubsauger Handbücher

Panasonic

Panasonic MC-UG502 Bedienungsanleitung

Panasonic

Panasonic QuickDraw MC-V6945 Bedienungsanleitung

Panasonic

Panasonic MC-BU100 Bedienungsanleitung

Panasonic

Panasonic MC-UL542 Bedienungsanleitung

Panasonic

Panasonic MCV5502 - UPRIGHT VACUUM Bedienungsanleitung

Panasonic

Panasonic MCV7341 - UPRIGHT VACUUM Bedienungsanleitung

Panasonic

Panasonic MCUG773 - UPRIGHT VACUUM - MULTI LANGUAGE Bedienungsanleitung

Panasonic

Panasonic MCV5203 - COMMERCIAL VACUUM Bedienungsanleitung

Panasonic

Panasonic MCE583 - UPRIGHT VAC.-PLAT Bedienungsanleitung

Panasonic

Panasonic Ultra-Pro MC-V200 Bedienungsanleitung

Panasonic

Panasonic MC-SB30JW147 Bedienungsanleitung

Panasonic

Panasonic MC-CG711 Bedienungsanleitung

Panasonic

Panasonic MCUG581 - PLATINUM UPRIGHT VAC Bedienungsanleitung

Panasonic

Panasonic MC-SBU1F Bedienungsanleitung

Panasonic

Panasonic MC-YL699 Bedienungsanleitung

Panasonic

Panasonic EY37A3 Bedienungsanleitung

Panasonic

Panasonic MC-E983 Bedienungsanleitung

Panasonic

Panasonic MCUG383 - UPRIGHT VACUUM - MULTI LANGUAGE Bedienungsanleitung

Panasonic

Panasonic MCUG581 - PLATINUM UPRIGHT VAC Bedienungsanleitung

Panasonic

Panasonic MC-7650 Bedienungsanleitung

Panasonic

Panasonic MCV7521 - UPRIGHT VACUUM Bedienungsanleitung

Panasonic

Panasonic MC-E851 Bedienungsanleitung

Panasonic

Panasonic MC-4500 Bedienungsanleitung

Panasonic

Panasonic MCUG775 - UPRIGHT VACUUM - MULTI LANGUAGE Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch

Craftsman

Craftsman CMCVS001D1 Bedienungsanleitung